Product Specifications

ILM-R Industrial
Laser Module
CLASS 1
LASER PRODUCT
LASER RADIATION
DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
ILM-R DIMENSIONS
ILM-35-R ILM-150-R ILM-500-R ILM-1200-R
Key dimensions
A
B
C
D
E
F
G
H
I
J
46
40
M4 x 0.7
46
40
M4 x 0.7
71
43
M6 x 1.0
Mounting dimensions
Please
contact
Carlson for
dimensions.
Dimensions given in mm
43 (Fig 1)
16 (Fig 1)
ø 18 (Fig 1)
116
106
54
ø 14
43 (Fig 1)
16 (Fig 1)
ø 18 (Fig 1)
116
106
54
ø 14
53 (Fig 2)
25 (Fig 2)
ø 30 (Fig 2)
139
129
83
ø 14
69 (Fig 3)
32 (Fig 3)
ø 46 (Fig 3)
147
137
124
ø 14
Electrical connections
• Fischer DBEE-102A054-130 is located on the rear of the ILM unit.
•
A standard 2 m adaptor cable is available with each unit,
which converts the Fischer connector to a 9-way D-type and
two flying leads for power.
The pin outs for these connectors are described
in the table below.
Function
Fischer
pin number
9-way D-type
pin number
GND (0 V)
+9 V to 24 V dc
Data out
Data in
Trigger out
1
2
3
4
5
5
Not connected
2
3
Not connected
MATERIAL
THIRD
ANGLE
PROJ.
DIMENSIONS IN MILLIMERERS
TOLERANCES UNLESS
OTHERWISE STATED
NON-ACCUMULATIVE
+/- 0.1
REVISION
1. ALL HOLES AND EDGES TO BE DE-BURRED
2. SURFACE TO BE MACHINED OR LINISHED
FINISH
PROTECTIVE FINISH
OF
SHEET
1 2
Ca
2x 3.30 -  6.00
M4x0.7 - 6H
A
B
C
Figure 1
A
B
C
Figure 2
Designer MGJG
Date 22/06/2015
Drawn By T Wallace
Date 22/06/2015
Sheet 4 of 4
Stock Number LM30037
Part No.
THIRD
ANGLE
PROJ.
Revision 01
1. ALL HOLES AND EDGES
TO BE DE-BURRED
2. SURFACES TO BE
MACHINED OR LINISHED
FINISH
PROTECTIVE FINISH
Title ILM1200 UNHOUSED OPTICS BENCH
Material
MDL
Project MDA128
All Dimensions are in mm.
Tolerances unless otherwise stated.
General +/- 0.1mm
Angular +/- 1
°
Hole Centres +/- 0.05mm
Reamed Hole Centres +/- 0.02mm
2x 6.20 - 10.00
M6x1 Helicoil - 6H
 8.00
 6.76 - 10.00
1/4-20 UNC HeliCoil - 3B
 8.00
SEE SHEET 2
NA
A
B
C
Figure 3
E
D
G
F
H
I
J
* * Max measuring ranges are recorded against Kodak white card
(90% reflectivity) and grey card (18% reflectivity).
** Completed to Kodak white card, statistical error of 1σ. Both
specifications are tested under standard Carlson test conditions.
*** Viewing the laser output with certain optical instruments
designed for use at distance (for example, telescopes and binocu-
lars) may pose an eye hazard.
**** Environmental compability requirements of EN
60529:1992+A1:2002.
Please note : Observed performance is application specific and
dependent on a number of enviromental and target parameters. As a
result it may vary from the performance figures stated above. It is the
customer’s responbility to confirm that laser performance is
acceptable for their application. Please discuss with your local
Carlson oce or distributor for further information. The following
clause applies for instruments delivered into the United States:
Complies with 24 OFR 1040. 10 and 1040. 11 except for deviations
pursuant to Laser Notice 50, dated 24 June 2007.