Owner`s manual

ManualsBrandsMini ManualsAutomobile AccessoriesR50

Installation Instructions

Page 1 of 9

March 2004

Phones, Navigation Accessory

Development

These Installation Instructions supersede those

dated February 2004.

Changes to this revision are identified by a black bar.

SUBJECT

MINI Hands-Free System Kit - P/N 84 11 0 302 897

MODELS

MINI Cooper (R50) w/o Harmon Kardon: Vehicle Production 03/2002 - On

MINI Cooper (R50) with Harmon Kardon*: Vehicle Production 09/2003 - On

MINI Cooper S (R53) w/o Harmon Kardon: Vehicle Production 03/2002 - On

MINI Cooper S (R53) with Harmon Kardon*: Vehicle Production 09/2003 - On

SUGGESTED INSTALLATION TIME: 1.0 hours

*Note: This MINI Hands-Free Phone System with Bluetooth

Wireless Technology installation kit is not

for vehicles with Harmon Kardon (HK) Audio Systems produced prior to 9/2003, as those vehicles will

require a different wiring harness.

“Never use any electronic device or make any inputs while driving that may distract you from driving

safely. Pay attention to traffic laws and road conditions\situations. Safe vehicle operation is the

driver's responsibility. Always wear your safety belt.”

These instructions were developed specifically for MINI vehicles and are not to be compared to any

existing instructions for vehicles other than MINI. No methods other than those specified in this

document are to be used to install the MINI Hands-Free Phone System with Bluetooth

Wireless

Technology in MINI vehicles.

PARTS INFORMATION

MINI Hands-Free Phone System Installation Kit Contents - P/N 84 11 0 302 897

Part Description Qty MINI Part Number

Control Module 1 84 11 0 302 896

Control Module Mounting Bracket 1 84 11 0 302 903

Multi-Function Controller 1 84 11 0 302 902

Controller Mounting Bracket 1 84 11 0 302 901

Module Mounting Screws (M4 x 16mm) 2 N/A

Multi-Function Controller - Mounting Tape 2 N/A

Microphone 1 84 11 0 302 900

Wiring harness* 1 84 11 0 302 895

Female Bullet Connectors 3 N/A

Cable ties (3mm x 104mm) 6 N/A

Owner’s Manual 1 84 11 0 302 892

  DO IT RIGHT THE FIRST TIME, ON TIME, EVERY TIME  

Install Manual P/N 01 29 0 309 308

MINI, a division of North America, LLC

Summary of content (9 pages)

PAGE 1
Installation Instructions Page 1 of 9 Phones, Navigation Accessory Development March 2004 These Installation Instructions supersede those dated February 2004. Changes to this revision are identified by a black bar.
PAGE 2
ADDITIONAL PARTS Part Description Left A-Pillar Cover Qty 1 MINI Part Number 51 43 7 029 459 REQUIRED TOOLS BMW terminal crimping tool p/n 408 449 from Wiring Harness Repair Kit 3 or Snap-on P/N PWC47 AMP terminal removal tool P/N 611 134 COMPONENT LOCATION: A - Control Module B - Controller C – Microphone INSTALLATION PROCEDURE: 1. Disconnect negative battery terminal. 2.
PAGE 3
3. Remove the blue lock (1) from radio harness by releasing tab and sliding upwards, then remove following terminals (2) using AMP terminal removal tool p/n 611 134: Pin 12- Ground Connector (Brown) Pin 15- Battery +12V (Red/Brown) Pin 16- Ignition +12V (Violet/Blue) Note: wire colors may vary depending on vehicle production changes. 4. Cut original terminals off of 3 wires (1) removed from locations 12, 15 &16. Cut wire as close as possible to existing terminal to maintain wire length. 5.
PAGE 4
10. Insert black 12-pin connector from hands-free kit harness (1) into lower right section of radio connector (2). 11. Connect male & female 3-pin connectors (3). Note: On vehicles equipped with Navigation and/or AUX Input the 12-pin connector (1) is already included in radio harness. It will be necessary to remove pins 6 & 12 from the hands-free kit harness 12-pin connector and insert them into the appropriate slots of the existing 12-pin connector. 12. Remove 2 upper screws to bulkhead (1). 13.
PAGE 5
19. Remove microphone cover from center overhead location. 20. Remove left A-pillar cover, if not already removed. (Refer to TIS RA 51 43 201) IMPORTANT: The A-Pillar cover is a one time use component and MUST BE REPLACED WITH A NEW PART ONCE REMOVED. 21. Route microphone harness with black 3-pin connector (1) from 18-pin connector of hands-free kit harness (2) along underside of dash, up through left-hand A-pillar (along windshield) and to microphone mount location in center overhead (3).
PAGE 6
29. Mount controller assembly (1) to right side of radio, sandwiched between center console (2) and right-hand radio trim pillar (3). Secure right and left trim pillars with original hardware (4). Hint: To better conceal the wiring of the controller, a small notch can be cut into the inside portion of the trim pillar to allow the wire to be routed inside the pillar. 30. Route controller cable (1) to wiring harness and connect to 4-pin connector (2). 31. Secure cable slack (4) with provided cable ties.
PAGE 7
PAIRING PROCEDURE: Pairing is needed for phone recognition and to prevent other mobile phones from establishing an unwanted wireless connection. Mobile phones that are not paired will not operate with the system. Pairing only needs to be done once for a mobile phone unless the device is deleted from the system's memory. The MINI Hands-Free System searches first for the most recently paired phone stored in memory. The first mobile phone found will be connected to the system.
PAGE 8
IMPORTANT: Pairing will only be successful if the Bluetooth feature of the mobile phone is activated and the phone is placed into the correct search mode in order to locate other devices that utilize Bluetooth® wireless technology. 10. As a connection is established between the phone and the Hands-free system, most mobile phones will display a message like: “searching” Followed by "Mini HF" once the MINI Hands-Free System with Bluetooth® Wireless Technology is detected. 11.
PAGE 9
Wiring Schematic MINI Hands-Free System (Without HK as of 3/02 & With HK as of 9/03) Connection to Main Harness (Wires Removed from Radio Connector) N9 Radio IGN. Batt. 1 Gnd. 2 3 15 16 12 0.5 RT 0.5 SW 0.5 SW 11 10 0.5 GN 0.5 VI 13 4 Audio + X2519 X8 0.5 GE Audio - 6 12 X4 0.5 BL/SW 0.5 BL/BR X7 11 10 Batt. IGN. Mic + Mic - 18 1 Gnd. 7 Audio + X1 Audio - Hands-Free Phone Module Controller Inputs 9 14 1 0.5 SW 1 16 Mute Tel-On 0.