Computer Accessories User Manual

www.minicom.com
International HQ
Jerusalem, Israel
Tel: + 972 2 535 9666
[e-mail]
North American HQ
Linden, NJ, USA
Tel: + 1 908 486 2100
[e-mail]
Technical support - [e-mail]
5UM30167 V1.1 7/10
KVM Extender USB
Quick Start Guide
KVM EXTENDER USB
1
1. Introduction
The KVM Extender USB system from Minicom is an advanced KVM extender that
performs the following functions:
· Extends KVM control over a computer up to a distance of 150m / 500ft
· Gives 2 users at 2 workstations control of 1 computer
· A 2-port KVM switch at the remote workstation
· Full USB keyboard and mouse control
2. System components
The KVM Extender USB system consists of:
· Transmitter
· Receiver
· 2 x VGA+USB cable
· 1 Power adapter for the Receiver
· 1 Screwdriver
· 8 non-stick rubber stops
3. The KVM Extender USB units
The figures below illustrate the Transmitter unit.
LOCK
MINICOM
KVM EXTENDER USB
LOCK CONTROL
Keyboard
USB connector
Mouse USB
connector
Lock button
Local + Lock
LEDs
Figure 1 Transmitter front panel
3.1 Transmitter Button / LEDs
Button / LED Function
Lock button Press to keep control of the connected
computer at the Transmitter position
Control LED Blinks when Transmitter position has control
of the Transmitter position computer
Lock LED Blinks after either Transmitter or Receiver
position presses the Lock button for control
QUICK START GUIDE
2
CONTROL POWER SYSTEM COMPUTER
Power connector Local monitor Computer cable
(Optional)
Control box
System cable
Figure 2 Transmitter back panel
The figures below illustrate the Receiver unit. The Receiver can be up to 150m / 500ft
away from the Transmitter.
Keyboard
USB connector
Mouse USB
connector
LOCK
MINICOM
KVM EXTENDER USB
LOCK LOCAL
LOCAL
Lock button
Local button
Local + Lock
LEDs
Figure 3 Receiver front panel
3.2 Receiver Buttons / LEDs
Button / LED Function
Lock button Press to lock control of the Transmitter
computer at the Receiver position
Local button Press to toggle control between the local
Receiver computer and the remote
Transmitter computer (see also section 8.1 on
page 6)
Lock LED Blinks after either Transmitter or Receiver
position presses the Lock button
Local LED Blinks when Receiver position has control of
the Receiver position computer
Power connector
CONTROL POWER SYSTEM COMPUTEREq
Luminance +
Equalization
selector
Lu
(Optional)
Control box
System cable
Local monitor Computer cable
Figure 4 Receiver back panel
KVM EXTENDER USB
3
4. Pre-installation instructions
Place cables away from fluorescent lights, air conditioners, and machines that are
likely to generate electrical noise.
5. Connecting the System
When using the system as an extender, extending KVM control from the computer up
to a distance of 150m/500ft, connect the system as in Figure 5. The connections are
explained below.
Receiver Transmitter
Extended User
position
CAT5 cable - 150m/500ft
VGA + USB cable
Figure 5 KVM Extender USB as an extender
5.1 Connecting the Transmitter
Connect a VGA + USB cable - illustrated below - to the Transmitter and a computer.
Connect the HD15 connector to the Transmitter Computer port and connect the VGA
and USB connectors to the local computer Monitor and USB ports.
Figure 6 VGA + USB cable
5.2 Connecting a KVM workstation to the Receiver
Connect a KVM workstation to the Receiver. Connect a keyboard and mouse to the
Receiver Keyboard and Mouse USB ports. Connect a monitor to the Receiver Monitor
port.