Specifications

ManualsBrandsMiniston ManualsSmart HomeZ-Wave Mini Smart Dimmer Plug

Please DO NOT use this switch to control Medical or Life Support equipment. Z-Wave devices should never be used to

control the On / Off status of Medical and / or Life Support equipment.

• DO NOT EXCEED RATINGS

• DO NOT USE TO CONTROL ANY DEVICE

WHERE UNINTENDED OPERATION COULD

CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)

Please exercise EXTREME CAUTION when using Z-Wave devices to control appliances. Reason being is because the appli-

ance you want to control may be in a separate room and if unintentional behavior occurs (such as adevice turning on or off -

either intentionally via schedules, or unintentionally via network error) this event may lead to a hazardous condition. For the

reasons, please note the following suggestions:

due to unattended, unintentional, or automatic power control.

1) Do not include Z-Wave devices in Groups or Scenes if they control appliances.

2) Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition

2. Your device may need to be within 100 feet of the controller to be included. If so, include the device to the network

within 10 feet of the controller and relocate it to the

desired position in your home. Be sure to refresh the network if the device is included

in this manner.

1. Plug the device you want to control into the Z-Wave Smart plug controlled outlet.

NOTE: Plug directly into the outlet, do not use with power strip.

Notes:

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufa-

cturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of

vendor to increase the reliability of the network. This Device supports Lifeline (association group 1) supporting 1 node for

lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will

be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the

“Device Reset Locally” function.

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.

2. Once the controller is ready to remove your device, press the manual/program button on the smart plug 3 times quickly.

Z-Wave Network Configuration

Adding Device To Z-Wave Network

Again: If you have issues with pairing / including, please move the device as close as possible to the hub and try again--you

can move to your final location when completed.

Note: If the manual button doesn't light up after pressed 3 times, please reset the

Device: click the button twice quickly then hold for at least 10 seconds. This operation could be done when manual control

is functional--single press can turn on / off the lamp.

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.

2. Once the controller is ready to add your device, press the Manual/ Program button on the smart plug 3 times quickly. The

blue LED will blink quickly. Auto-add mode: LED will blink within 30 seconds after first plugged in. Now, you have complet-

ed control to turn your fixture ON/OFF according to groups, schedules and interactive automation programmed by your

controller. If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices.

Group 1 supports 1 node ID,Group 2 Supports maximum of 5 node ID’s

Association Group 1: Z-Wave Plus Lifeline

Association Group 2: Send Basic Set ON / Off

If you'd like to reset the KWH record, just click the button 10 times very quickly. Network exclusion or factory reset will

NOT automatically erase the KWH data.

Manual: Click the button twice quickly then hold for at least 10 seconds. (Light flashes once when reset successfully.)

Host reset: Remove it from hub the device will be restore to factory default.

Parameter Settings

Our Products warrant this product to be free from manufacturing defects for a period of one year from the original date of

consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to cons-

equential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other war-

ranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the excl-

usion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives

you specific rights, and you may also have other rights which vary from state to state.

Warranty

KWH Reset:

To Return The Device To Factory Defaults:

To Remove The Device:

Association Group:

Adding Device To Z-Wave Network for QR CODE

Scan here for SmartStar inclusion

Note: DSK Code can be found on the packaging box.

Do not remove or damage them.

Program button

Press 1x: Manually

Press 3x: Z-Wave Network configuration

Reset: Press the button twice then hold it for 10 seconds

LED indicator

Blue: Light status indicator

Blue: ADD / Inclusion

Purple: Remove / Exclusion

Red: Network Failure / Over-temperature Warning

MP21ZD (ZW39SU)

Z-Wave Dimmer plug

Indoor use in dry location

Specification

Input: 125VAC 60Hz

Frequency: 908.42 MHz

100W Dimmable CFL/LED

Loading: 200W Incandescent

Features:

1. Z-Wave on / off + dimmer control.

2. Grounded 3-wire power connection for safety.

3. Remember and restore on/off status after power failure.

5. S2 security and 700 Z-Wave chip for reliable wireless communication.

6. Work with all certificated Z-Wave controllers.

4. Built-in Z-Wave Plus signal repeater to extend network range.

Please contact us if you have any questions:

ask@minoston.com

www.minoston.com

Z-WAVE INTEROPERABILITY

FCC / IC

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subjected

to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any

interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modiﬁcations to

this equipment. Such modiﬁcations could void the user’s authority to operate the equipment.

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio / TV technician for help.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins-

tallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interfe-

nce will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recepre-

tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

CAUTION - PLEASE READ!

This device is intended for installation in accordance with the National Electric Code and local regulations in the United States,

or the Canadian Electrical Code and local regulations in Canada If you are unsure or uncomfortable about performing this

installation consult a qualiﬁed electrician.

WARNING

RISK OF FIRE / RISK OF ELECTRICAL SHOCK / RISK OF BURNS

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUN-

DING TYPE PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL

ONLY FIT INTO A GROUNDING TYPE POWER OUTLET. IF THE PLUG DOES

NOT FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO

INSTALL THE PROPER

OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY.

CONTROLLING APPLIANCES:

CAUTION: TO REDUCE THE RISK OF

OVERHEATING AND POSSIBLE DAMAGE TO

OTHER EQUIPMENT

COMMANDCLASS:

0x5E - ZWAVEPLUS_INFO

0x25 - SWITCH_BINARY

0x70 - CONFIGURANTION

0x85 - COMMAND_CLASS_ASSOCIATION

0x8E - COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION

0x59 - COMMAND_CLASS_ASSOCIATION_GRP_INFO

0x55 - COMMAND_CLASS_TRANSPORT_SERVICE

0x86 - COMMAND_CLASS_VERSION

0x72 - COMMAND_CLASS_MANUFACTURER_SPECIFIC

0x5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY

0x87 - COMMAND_CLASS_INDICATOR

0x73 - COMMAND_CLASS_POWERLEVEL

0x9F - COMMAND_CLASS_SECURITY_2

0x6C - COMMAND_CLASS_SUPERVISION

0x7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD

Command Class Information

GRNERIC DEVICE CLASS: 0x10 - SWITCH BINARY

SPECIFIC DEVICE CLASS: 0x00 – NOT_USED

100 feet

MEDICAL EQUIPMENT

CONTROLLING APPLIANCES

Over-temperature protection is protection against overheating of the protected equipment.

When the device's temperature is high, the LED will light up in red and cut down the power.

Please power off the device and use it after the temperature of the device drops.

Overloading

Warning

This parameter can access you to set a timer to make the switch turn off automatically after the switch turns on.

(LED flashes 3 times when the configuration parameter changed.)

--- Parameter =4, Size=4，Value: 0– 65535(minutes);

Value=0(default) disable

Auto Turn-Off Timer

The numberentered as value corresponds to number of minutes. Operation: Set up on the hub.

LED Indicator

This parameter can access you to choose the LED indicator to be on when the plug(light) is on/off, or LED indicator remains

on/off all times. (LED flashes 3 times when the configuration parameter changed.)

Value=1 --- LED is On when switch (light) is Off.

--- Parameter =2, size =1byte, Default =0

Value=0 (default) LED is On when switch (light) is On.

Value=2 --- LED is always Off.

Value=3 --- LED is always On.

This parameter can access you to set a timer to make the switch turn on automatically after the switch turned on.

The numberentered as value corresponds to number of minutes.

(LED flashes 3 times when the configuration parameter changed.)

--- Parameter =6, Size=4，Value: 0– 65535(minutes);

Value=0(default) disable turn on the outlet

Auto Turn-On Timer

Operation: Set up on the hub.

This parameter can access you to set a specific brightness for the light when you want to make it as a night light.

--- Parameter =7, Size=1, Default = 2

Value=1 --- 10% brightness

Value=2 --- 20% brightness

Value=10 --- 100% brightness

Night Light Set

(LED flashes 3 times when the configuration parameter changed.)

This parameter can access you to set the switch to be on/off after power failure.

Operation: quickly press 8 times to change this parameter.

Parameter=8，Size=1，Value=2(default)

Value=0 --- The switch is off regardless of the state prior to power failure.

Value=1 --- The switch is on regardless of the state prior to power failure.

Value=2(default) memory state before power failure

This switch will be return to state prior to the power failure after power is restored.

(LED flashes 3 times when the configuration parameter changed.)

This parameter can access you to set the time from maximum brightness to minimum brightness or minimum brightness to

maximum brightness (Only when turn ON / OFF the light )

Operation: Set up on the hub.

(LED flashes 3 times when the configuration parameter changed.)

Value=0 --- instant on/off

Parameter=9，Size=1, Default = 2

Value=1--- from 0x63 to 0x00 or from 0x00 to 0x63 need 1s

Value=2 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 2s

Value=10 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 10s

This parameter can access you to set the time from maximum brightness to minimum brightness or minimum brightness to

maximum brightness.

Operation: Set up on the hub.

(LED flashes 3 times when the configuration parameter changed.)

Parameter=10，Size=1, Default = 4

Value=1 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 1s

Value=2 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 2s

Value=10 --- from 0x63 to 0x00 or from 0x00 to 0x63 need 10s

(Only when hold it to change the brightness or control from HUB).

Operation: quickly press 5 times to change this parameter.

(LED flashes 3 times when the configuration parameter changed.)

Value=0 --- disable

Value=1

Value=99

---Parameter=11，Size=1，Default = 10

Value=1

Value=99

(LED flashes 3 times when the configuration parameter changed.)

---Parameter=12，Size=1，Default = 99

Value=0 --- disable

Operation: quickly press 10 times to change this parameter.

Multilevel minimum value can be set

Multilevel maximum value can be set

Restores state after power failure

Dimmer speed (ON/OFF Control)

Dimmer speed (Dimmer Control)

正面

背面

SIZE: 190 x 190 mm

材质：80G 书写纸

单色黑白印刷

拆法：风琴页 47 x 47 mm 成品

MP21ZD