Installation Sheet

INSTALLATION INSTRUCTIONS
For Model #1013-PL
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT PO WER OFF AT FUSE OR CI R C U I T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
NOTE
Turn off the main power at the circuit breaker before installing
the fixture, in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with local
and national electrical code (N.E.C) standards. If you are
unfamiliar with proper electrical wiring connections obtain the
services of a qualified electrician.
Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to lose any small parts necessary
for installation.
ASSEMBLY AND INSTALLATION
1. Turn off the power
2. SOCKET INSTALLATION (See FIG.1.).
Insert the SOCKET (1) into the SOCKET PLATE (2) by pushing
up the socket. Be sure that the sockets protrude out from
provided slots of the socket plate.
3. END PLATE INSTALLATION (See FIG. 2.).
Insert the END PLATE (3) into the U CHANNEL (4) by snapping
into the hole of U channel.
4. SECURE THE CLIP (See FIG. 3).
Secure the Clip (5) to the end of the U Channel (4) by using the
screws provided.
5. Secure the Circular Strap (8) to the Outlet Box (6) by tightening
the two Mounting Screws (10). (Size: #8-32*0.75"L)
6. Position the U Channel (4) over the Outlet Box (6), mark the
location of the two key holes located on the U channel (4) onto
the ceiling. Remove the U Channel (4) from the ceiling. Drill the
two holes using an appropriately sized drill bit. Insert the
provided ceiling Anchors (7) into the holes.
7. Make the wiring connections: connect the white supply wire to
the white fixture wire; connect the black supply wire to the black
fixture wire; connect the house ground wire to the fixture ground
wire by using the wire connectors. Carefully tuck all wires back
into the Outlet Box. (See FIG. 6).
8. Locate the U channel (4) over the Circular Strap (8) through the
2 Outward Screws (9) and secure it by tightening two Nuts (11)
9. Feed the two Anchor Screws (12) through the two key holes on U
Channel (4). Tighten the Anchor Screws (12) into the ceiling
anchors (7).
10. Insert the tab on the end of Face Cover (13) to the hole of the
Socket Plate (2) and secure the face cover to the U Channel (4)
by twisting the Fastener (16). (See FIG. 4).
11.Now you are ready to install the Lamps (14). Do not exceed the
recommend wattage. (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE) (Simultaneously insert the pins into
both ends of the fixture and rotate the bulb until you hear and
feel them lock into place)
12. Carefully push the Diffuser (15) to the Clips (5) until the Diffuser
(15) is held by the Clips (5) onto the fixture body.
13. The color correlated Temperature (CCT) for replacing the
recommended lamp is (4100K).
INSTALLATION IS NOW COMPLETED
The ballast in each of these models can be replaced by a qualified
electrician without cutting of wires and without damage to the
housing, trim, decorative elements or carpentry to which the
fixture is attached. See installation steps for more detail.
FIG. 6
FIG.4.
FIG.5.
Use screw driver to loosen
the ballast screw and take it
out of fixture pan.
Insert the Ballast to the triangle
hole and then secure it by the
screw on the other end.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
LIMITED 3 YEAR WARRANTY
This Fixture is covered by a Limited 3 year Warranty from the Manufacturer,
effective from the date of purchase. This fixture is warranted against defects in
the quality of the housing, trims, diffuser, shades, and electrical components.
Fixture finishes and/or lamps (bulbs) are expressly excluded from this
warranty; refer to bulb manufacturer for lamp warranty.