Manualshelf

Instructions / Assembly

ManualsBrandsMinka Lavery ManualsLightingAudreys Point 1-Light Polished Nickel Mini Pendant
12
INSTALLATION INSTRUCTIONS
Item#3290-613 (New. 11/18/2015)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
LA-2520E
PREPARATION (Fig. 1)
1.
Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully remove the fixture from the carton and check
that all parts are included as shown in the illustration.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP
(Fig.
2)
3. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the nipple (I) of the fixture body (J).
Then attach loop (H1) by screwing in to rod (F1). Note:
remove the nipple if installing with one 6” rod only.
4. Attach the quick link (G) connect to loop (H1
) and loop
(H2) on the canopy (E
), carefully feed the wire over loop
(H1), quick link (G) and loop (H2).
5. Thread Screw (A) into the pre-drilled holes in the circular
strap (B
) spaced the same distance apart as the holes in
the back-plate and secure with Hex Nut (C).
6. Attach the circular strap (B) to the Junction box using
mounting screws (D) (Size: #8-32N*L0.5”). The side of
the circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
7.
At this point, connect the electrical wires as shown in
figure 3, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or bare
copper), connect the fixture’s ground wire to it
.
Otherwise, connect the fixture’s ground wire
directly to
the circular strap using the green screw provided.
8. Tuck the wire connectors neatly into the ceiling Junction
Box and then raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
9. Thread screws (A) into canopy (E),
knurled knobs (T).
10. Place the glass shade (L) over the socket (K) and
secure it with socket ring (M).
11. Install the light bulb(s) (N) (not included) in accordance
with the fixture’s specifications. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!) (
NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the
junction box and test the fixture.
Note: Illustration (Fig. 1) on this manu
al is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOU
SE
WIRES
Green
(Ground)
Set
#
A
-
0
22
-Circular Strap
-Ground screw
-Mounting Screw*2
Rod#
W30
-
1
-
613
*1
(F1)
W30-1-613*2(F2)
W30-H-613*1(F3)
Socket ring # SKT-RING-26
L
M
A
B
C
E
T
I
J
K
D
N
F3
G
H1
F2
F1
H2

Summary of content (2 pages)