Installation Guide

INSTALLATION INSTRUCTIONS
Item#3568-098 (New. 01/08/2018)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
LA-2912E
PREPARATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If necessary,
remove the old fixture, including the mounting hardware.
2. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 1&Fig.
2)
3. Place the candle cover (R) over the socket (Q) of the fixture body.
4. Install light bulb(s) (K) (not included) in accordance with the
fixture’s specification.
(DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
5. Thread screw (L) into the square tube (J), then plastic gasket (S),
glass panel (O), plastic gasket (S), iron plate (M) to secure with
ball nut.
6. Secure metal tube (U) into nipple (I).
7. Determine the desired hanging height and thread rods (F1, F2
and F3) to the nipple of the metal tube (U). Then attach loop (H1)
by screwing in to rod (F1). Note: remove the nipple if installing
with one 6” rod only.
8. Attach the quick link (G) connect to loop (H1) and loop (H2) on the
canopy (D), carefully feed the wire over loop (H1), quick link (G)
and loop (H2).
9. Thread screws (A) into the pre-drilled holes in the circular strap
(B) spaced the same distance apart as the holes in the canopy
(D).
10. Attach the circular strap (B) to the Junction box using mounting
screws (C) (Size: #8-32N*L0.5”). The side of the circular strap
marked “GND” must face out.
11. The support cable is provided to support the weight of the fixture
while wiring. Align the fixture to circular strap (B) and attach hook
(T) on the end of support cable (N) into a slot located on circular
strap (B). Carefully allow the support cable (N) to support the
weight of the fixture while wiring (Fig.1).
CONNECTING THE WIRES (Fig. 3)
12. At this point, connect the electrical wires as shown in figure 3,
making sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw provided.
13. Tuck the wire connectors neatly into the ceiling Junction Box and
then raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
14. Thread canopy (D) into screws (A), and secure with knurled knobs
(E).
Your installation is now complete. Return power to the junction
box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Set# A-020-A
-Circular Strap
-Ground Screw
-Mounting Screw*2
Rod# W30-1-84*1(F1)
W30-1-84*2(F2)
W30-H-84*1(F3)
Candle Cover#CCV24060P-84
FIXTURE
WIRES
Black or
Smooth
H
O
U
S
E
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
O
U
S
E
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
O
U
S
E
WIRES
Green
(Ground)
K
R
I
L
M
S
J
S
O
Q
F1
G
H1
H2
E
D
A
C
B
N
T
F2
F3
U