Installation Guide

INSTALLATION INSTRUCTIONS
For item#4089-107 (New. 02/26/2019)
READ AND SAVE THESE INSTRUCTIONS
WAR NI N G! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
PREPARING FOR INSTALLATION (Fig. 1&Fg. 3)
1. Shut off power at the fuse box or circuit breaker and
remove the old fixture included the mounting hardware.
2. Carefully unpack your new fixture and lay out all the
parts on a clean area. Take care not to lose any small
parts necessary for installation.
3. Thread the center tube (D) to nipple (F) of fixture body.
Install rods (E) into coupling (G) of arms.
4. Secure center tube (D) and rods (E) to the metal plate
(C) by using loop (A) and knurled knobs (B) as showed
Fig.3 (Not over tighten when securing the rods).
5. Thread the nipple into the ceiling loop until snug.
6. Thread the other end of the nipple into the crossbar
until snug. Note: The length of the nipple into the
crossbar may be adjusted if necessary.
7. Use the lock washer and hex nut to secure the nipple
into the crossbar.
8. Take this crossbar assembly and mount it to ceiling
outlet box with mounting screws (Size: #8-32N*L0.5”).
The side of crossbar marked with “GND” must face out.
9. Determine the desired hanging height and use a pair of
proper chain pliers to remove and discard the excess
chain.
10. Open one end of chain and attach it to fixture loop and
close the chain. Slip the lock collar and canopy over the
chain and allow them to rest on the fixture body. Open
the other end of the chain and attach it to ceiling loop
and close the chain.
11. Carefully lace the fixture’s wires through the chain.
Feed the fixture wires through the loop and nipple
assembly.
CONNECTING THE WIRES (Fig. 2)
12. At this point, connect the electrical wire as shown in
figure 2, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or bare
copper), connect the fixtures Ground Wire to it.
Otherwise, connect the fixture Ground Wire directly to
the crossbar using the Green Screw provided. After
wires are connected, tuck them carefully inside the
outlet box.
COMPLETING THE INSTALLATION（Fig. 1&Fig. 3)
13. Raise the canopy to the ceiling and secure it with lock
collar to the fixture ceiling fixture.
14. Place the candle cover (I) over socket (H).
15. Install the light bulbs (J) (not included) in accordance
with the fixture’s specifications. (DO NOT EXCEED
THE MAXIMUM WATTAGE RATING!!) (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
16. Place the glass shape (K) on the cup (L).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration (Fig. 3) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-3051E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
Set# A-010
- Crossbar
- Ground screw
- Mounting Screw*2
Ceiling Loop
Canopy
Outlet Box
Mounting Screw
Nipple
Lock Collar
Crossbar
Hex Nut
Lock Washer
Wire
Chain
Loop
Chain#HCH2072-172
Candle Cover#CCV21082P-AGL
E
F
G
L
H
I
J
K
A
B
C
D