Installation Guide

ManualsBrandsMinka Lavery ManualsLightingTannehill 6-Light Aged Brass Billiard Light

INSTALLATION INSTRUCTIONS

For item#4596-575 (New. 11/14/2017)

READ AND SAVE THESE INSTRUCTIONS

WAR NI N G! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off the power at the fuse box or circuit breaker box

and remove the old fixture from the ceiling, including the

mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts

in a clear area. Take care not to lose any small parts

necessary for installation.

3. Position the mounting plate (C) on the ceiling, and mark

location of the two mounting holes. Drill the holes on the

wall, and then insert the plastic anchors (A).

4. Attach the mounting plate (C) to the junction box using

mounting screws (B) (Size: #8-32N*L0.5”). The side of the

mounting plate marked “GND” must face out.

5. Secure the mounting plate (C) by inserting the wood

screws (D) through the holes on the mounting plate into

the plastic anchors (A).

6. Secure metal tube (J) into nipple (I) of the fixture body (L)

7. Determine the desired hanging height and thread rods

(F1, F2 and F3) to the nipple of the metal tube (J). Then

attach loop (H1) by screwing in to rod (F1). Note: remove

the nipple if installing with one 6” rod only.

8. Attach the quick link (G) to loop (H1) and loop (H2) on the

canopy (E), carefully feed the wire over loop (H1), quick

link (G) and loop (H2).

CONNECTING THE WIRES (Fig. 2)

9. At this point, connect the electrical wires as shown in

figure 2, making sure that all wire connectors are secured.

If your outlet has a ground wire (green or bare copper),

connect the fixture’s ground wire to it. Otherwise, connect

the fixture’s ground wire directly to the circular strap using

the green screw provided.

10. Tuck the wire connectors neatly into the ceiling Junction

Box and then raise the canopy all the way to the ceiling.

COMPLETING THE INSTALLATION (Fig. 1)

11. Place canopy (E) over the mounting plate (C) and secure

it with screws (F).).

12. Place the candle cover (M) over the socket.

13. Install light bulb(s) (N) in accordance with the fixture’s

specification. (DO NOT EXCEED THE MAXIMUM

WATTAGE RATING!) (NE PAS DEPASSER LA

PUISSANCE NOMINALE MAXIMALE!).

14. Place the glass shade (O) twist to holder (K). (In clockwise

direction)

Your installation is now complete. Return power to the outlet

box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation

purposes only. It may or may not be identical to the fixture

purchased.

LA-2857E

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Set# A-021-300118

- Mounting Plate

- Ground screw

- Mounting Screw*2

Rod# W30-1-575*2(F1)

W30-1-575*4(F2)

W30-H-575*2(F3)

Candle Cover# CCV24060P-575