Instructions / Assembly

INSTALLATION INSTRUCTIONS
Model # 73114
READ AND SAVE THESE INSTRUCTIONS
WARNI NG! S HUT POWER O FF AT F US E OR CI RCUI T BRE AK ER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Notice:It is important to use proper chain pliers(not included)
To OPEN and CLOSE the chain included with this fixture.Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
BARE COPPER(GROUND)
Fig.2
FIXTURE
WIRES
RIBBED
BLACK
(HOT)
WIRES
HOUSE
GREEN OR
WHITE
(NEUTRAL)
WIRES
HOUSE
(GROUND)
COPPER
BARE
FIXTURE
WIRES
SMOOTH
WIRES
FIXTURE
GREEN OR
HOUSE
WIRES
Fig. 1
PREPARING FOR INSTALLATION (Fig.1)
1. Shut off the power at the fuse box or circuit breaker box
and remove the old fixture, including the mounting
hardware.
2. Carefully unpack your new fixture and lay out all the
parts in a clear area. Take care not to misplace any
small parts necessary for installation.
3. Screw threaded nipple (F) into loop (I) until snug.
4. Screw the other end of threaded nipple (F) into the
crossbar (B) and secure with hex nut (C). Note the
length of threaded nipple (F) into crossbar (B) may
need to be adjusted. Attach the crossbar assembly to
the ceiling outlet box (A) (not included) with screws (D).
Note: The side of the crossbar (B) marked “GND” must
face out.
HANGING THE FIXTURE (Fig.1)
5. Determine the desired hanging height and remove the
excess chain with proper chain pliers to avoid
damaging the finish.
6. Open one end of the chain (J) and connect it to the
fixture loop (K) and close the link.
7. Slide lock ring (H) followed by canopy (G) over the
chain and allow them to carefully rest on the fixture
body.
8. Thread the wire carefully through the chain links.
9. Open the other end of the chain (J) and attach it to
chain loop (I) and close the link.
10. Feed the wires through loop (I), and nipple (F).
CONNECTING THE WIRES (Fig.2)
11. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the crossbar (B) using
the green screw (E) provided. Tuck the wire
connections neatly into the outlet box (A).
FINISHING THE INSTALLATION (Fig. 1)
12. Raise the canopy (G) to the ceiling and secure with
lock ring (H).
13. Slide the frame (M) onto cap (L) and secure with socket
ring (N). (Fig 1)
14. Install (1) one medium base bulb (O) up to 60 watts or
CFL or LED equivalent (not included) in accordance
with the fixture specification. —DO NOT EXCEED
THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Your installation is now complete. Return power to the junction
box and test the fixture.
“CAUTION-RISK OF FIRE CONSULT A
QUALIFIED ELECTRICIAN TO ENSURE
CORRECT BRANCH CIRCUIT CONDUCTOR”
ATTENTION – RISQUE D’INCENDIE, CONSULTER
UN ÉLECTRICIEN QUALIFIÉ POUR VOUS
ASSURER QUE LES CONDUCTEURS DE LA
DÉRIVATION SONT ADÉQUATS.
Notice:It is important to use proper chain pliers(not included)
To OPEN and CLOSE the chain included with this fixture.Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
Chain# HCH2072-226
Part# A-010
Crossbar (1)
Ground Screw (1)
Mounting Screws (2)