Model NO.
©2021 Minka Lighting Inc. Manual design and all elements of manual design are protected by United States Federal and/or State Law including Patents, Trademark, and/or Copyright Laws.
The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer. This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs excluded) for one (1) full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling fan (excluding wall controls and electrical components), to the original purchaser or user.
6 INSTALLING THE CANOPY AND CANOPY COVER INSTALLING THE BLADE ARM TO THE FLYWHEEL INSTALLING THE FLYWHEEL TO THE FAN MOTOR ASSEMBLY ATTACHING THE BLADES TO THE BLADE ARM INSTALLING THE 16W LED ASSEMBLY 14 15 16
READ AND SAVE THESE INSTRUCTIONS. 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 701999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs.
D E 5 7. Fan motor assembly 8. Blade arm(5) 9. Flywheel 10. 16W LED assembly 11. Receiver(1) + wire nut (6) 12. Transmitter + holder + 2 mounting screws + A23 12 volt battery B. Blade attachment hardware: 3/16” x 8mm blade screws ( 15 + 1 spare) Fiber washers ( 15 + 1 spare) C. Blade arm attachment hardware: 1/4” x 10.5mm blade arm screws (10 + 1 spare) D. Flywheel attachment hardware: 1/4” x 10.5mm flywheel screws (5 + 1 spare) E.
Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. MOUNTING OPTIONS If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs.).
WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the proper installation of your new ceiling fan. The use of other parts, hardware or components not supplied by Minka Aire®with the fan will void the Minka Aire® Warranty. REMEMBER to turn off the power. Follow the steps below to hang your fan properly: OUTLET BOX Step 1.
Step 5. Slip coupling cover, canopy cover and canopy onto downrod. (Fig. 9) Carefully reinstall hanger ball onto rod being sure that cross pin is in the correct position, set screws are tighten and wires are not twisted. CANOPY DOWNROD CANOPY COVER SET SCREWS LOCK PIN Fig. 9 Step 6. Now lift motor assembly into position and place hanger ball into hanger bracket. Rotate until the check groove has dropped into the registration slot and seats firmly. (Fig.
11 12 13 13 13 Fig. 11 Fig. 13 Fig.
INSTALLING THE CANOPY AND CANOPY COVER 14 14 OUTLET BOX HANGER BRACKET HANGER BALL CANOPY CANOPY COVER Fig.
INSTALLING THE BLADE ARM TO THE FLYWHEEL Insert the blade arm through the slot on the flywheel. Attached the blade arm to the flywheel using the two blade arm screws and tighten them securely. Repeat the step for the other four blade arms. (Fig.15) BLADE ARM SCREW BLADE ARM FLYWHEEL Fig.
INSTALLING THE FLYWHEEL ASSEMBLY TO THE FAN MOTOR ASSEMBLY Tighten the flywheel onto the bottom of fan motor assembly by using the five flywheel screws. (Fig.16) FAN MOTOR ASSEMBLY FLYWHEEL SCREW FIG.
ATTACHING THE BLADES TO THE BLADE ARM Attach the fan blade to the blade arm by using the three blade screws and the three fiber washers. Tighten all blade screws and washers securely. Repeat same process for the other four blades. (Fig.17) BLADE SCREW FIBER WASHER BLADE BLADE ARM FIG.
INSTALLING THE 16W LED ASSEMBLY CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan Before Installing The Light Kit. Step 1. While holding the 16W LED assembly under your fan, firmly snap the wire connection plugs together. Step 2. Attach the 16W LED assembly to the switch box by twisting tightly. NOTE: This is an integrated LED light kit assembly and can not be disassembled to prevent electronic shock. SWITCH BOX WIRE CONNECTION PLUGS 16W LED ASSEMBLY FIG.
Restore Power to Ceiling Fan. A. Buttons: These buttons are used to set the fan speeds as follows; = Low Speed = Medium Speed = High Speed B. Button: This button turns the fan off. C. FIG. 19 Button: These buttons turn the light ON or OFF and also control the brightness settings of the light.
The reverse switch is located on the fan motor assembly (Fig.20). Slide the switch to the Left for warm weather operation. Slide the switch to the Right for cool weather operation. 21 22 FIG. 20 FIG. 21 FIG.
WARNING! MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY REPAIRS. REFER TO THE SECTION, “ELECTRICAL CONNECTIONS”.
15
120 0.27 15.05 67 54 120 0.55 65.47 7.13 9.21 153 3,286 12 76 43 1,793 15.05 119 4,602 65.47 70 16 1.
