TWIST
F678L
INSTALLING THE LIGHT KIT ENJOY YOUR SMART CEILING FAN 3
8 9 0
MK1000-BOND RC1000 FAN
13. Receiver(9 wire nuts included) Lock washers (2 pcs.) 4mm Star washers (2 pcs.) Washers (2 pcs.) 20W PC 10. Blade fixing ring 11. Light kit plate 12. Remote control with holder and 2 mounting screws (1.5V*2AAA battery included) B Balance kit C. Blade attachment hardware: C1. 1/4*16mm+S screw(7 pcs) 1/4(Φ6.6*13*0.8mm) flat washer (7 pcs) C2. 5/32*10mm+S screw (7 pcs) D Wire nut(3pcs) A 1 #10x38mm Wood screws(2 pcs.) #8-32x38mm Machine screws(2pcs.
Screw Assemble the blade onto the motor. Align the two holes of the blades with the motor and tighten them with the screw pack C1.(Fig.5)Then, Convert the fan body, assemble the blade fixing ring with the provided screws C2 in parts bag. Blade fixing ring Fan body Fig.5 Fig.
Step 1: Remove the clevis pin and B clip from downrod assembly.(Fig. 7 ) Step 2: Remove the cross pin and set screw from downrod assembly.(Fig. 8 ) Step 3: Route wires through coupling cover,canopy cover,canopy and hanger ball.(Fig. 9 ) Step 4: Thread the rod into the motor shaft, tighten the set screw,clevis pin, and slip the coupler cover on to the fan body.(Fig.10 & Fig.
Hanger ball Downrod Set screw Downrod Canopy Cross pin Canopy cover Set screw Downrod B clip Coupling cover Clevis pin Coupling cover Downrod Cross pin Coupler Fan body Outlet box Hanger ball Set screw Hanger bracket Washer Star washer Spring washer Canopy B clip Screw Clevis pin Fig.7 Hanger bracket Downrod Fig.8 Fig.9 Fig.10 Fig.11 Fig.12 Fig.13 Fig.
1024 5 (Fig.16) Fig.
Step 2: Motor to Receiver electrical connections: connect the WHITE WIRE from the fan to the WHITE wire from receiver. Connect the RED wire from the fan to the RED wire from the Receiver. Connector the BLUE wire from the fan to the BLUE wire from the recelver. connect the PURPLE wire from the fan to the PURPLE wire from the receiver. Connect the GREY wire from the fan to the GREY wire from the receiver.(Fig.
8 Canopy Canopy Screw Screw 9 Canopy Cover 9 cover 20 Fig.18 Fig.19 Fig.
INSTALLING THE LIGHT KIT / Step 5: Tighten the LED assembly to light kit plate with 3 screws.(Fig. 26) Step 6: Align the slot of the light shade with the aised dimple on the light kit plate Step 1: Remove 1 of 3 screws on light kit adapter and loosen the other 2 screws.(Fig. 21) Step 2: Slide the light kit plate up towards the light kit adapter and place the key holes over the screws on the light kit adapter. Turn light kit plate until it locks in place at the narrow section of key holes.(Fig.
Light kit adapter Light kit plate Screw Screw Plug Fig.21 Fig.22 Light kit plate Light kit plate Block Slot Screw Screw Fig.23 Fig.24 Fig.25 Fig.26 Light shade Fig.
9 2pcs AAA battery
28 (CLOCKWISE DIRECTION) (COUNTERCLOCKWISE DIRECTION) 29 Fig.28 Fig.
30 Fig.
60
120 0.09 2.78 53 5.1 52 120 0.53 33.55 148 7.00 2.
6 3,677 1804 2.78 649 5330 33.
