Network Card User Manual
Table Of Contents
- Network Interface Card
- Foreword
- Contents
- Ch.1 Introduction
- Ch.2 Installing the Network Interface Card
- Ch.3 Utilizing Windows Programs
- Ch.4 NetWare Configuration
- 4.1 Configuring NetWare 2.15 and 3.x
- 4.1.1 Start PCONSOLE and Select File Server
- 4.1.2 Create Print Queues
- 4.1.3 Enter the Print Server Name
- 4.1.4 Configure the Print Server
- 4.1.5 Assign Print Queues to the Printer
- 4.1.6 Set Up Notify Options for the Printer (Optional)
- 4.1.7 Installing the Print Server on Multiple File Servers
- 4.1.8 Primary File Server
- 4.1.9 Preferred File Servers
- 4.2 Configuring NetWare 4.x - Bindery Emulation
- 4.3 Configuring the NIC in Novell Directory Services
- 4.4 NIC Configuration
- 4.5 Using the Novell PCONSOLE Utility
- 4.1 Configuring NetWare 2.15 and 3.x
- Ch.5 AppleTalk Configuration
- Ch.6 TCP/IP Configuration
- 6.1 Installation in a Windows Environment
- 6.2 UNIX Printing
- 6.2.1 Configuring the IP Address on the NIC
- 6.2.2 lpd Printing
- 6.2.2.1 Setting Up a BSD Remote Printer to Use lpd
- 6.2.2.2 Setting Up an AIX 2.5 Remote Printer to Use lpd
- 6.2.2.3 Setting Up an AIX 4.0 System
- 6.2.2.4 Setting Up an HP/UX Remote Printer to Use lpd
- 6.2.2.5 Setting Up an AS/400 Systems to Use lpd
- 6.2.2.6 Setting Up a DEC ULTRIX 4.3 RISC or OSF1/ ALPHA Remote Printer
- 6.2.2.7 Setting Up a SCO UNIX Remote Printers to Use lpd
- 6.2.2.8 Setting Up System V Rel.4 and Solaris 2.X to Use lpd
- 6.2.3 Installing TCP/IP for NIC If Not Running lpd
- 6.2.3.1 Loading the Software
- 6.2.3.2 Script Selection of Filters
- 6.2.3.3 Manual Selection of Filters
- 6.2.3.4 Installing and Printing on Solaris 1.X and OSF1/ALPHA Systems
- 6.2.3.5 Installing & Printing on an DEC ULTRIX 4.3 RISC System
- 6.2.3.6 Installing and Printing on the HP/UX System
- 6.2.3.7 Installing and Printing on a System V (Solaris 2.X)/System V Rel.4 386-based Machine
- 6.2.3.8 Installing & Printing on a SCO UNIX System
- 6.2.3.9 Installing and Printing on an AIX RISC System/6000
- 6.3 Running Telnet
- 6.4 FTP Printing
- 6.5 Dynamic Host Configuration Protocol
- Ch.7 Operation and Troubleshooting
- 7.1 LED Status Indicator
- 7.2 Status/Configuration Report
- 7.3 Resetting the NIC to Factory Default
- 7.4 How to Diagnose Problems
- 7.5 Troubleshooting Checklists
- 7.5.1 Troubleshooting Network Hardware Connections
- 7.5.2 Troubleshooting NetWare Protocol
- 7.5.2.1 NetWare Checklist
- 7.5.2.2 File Server Checklist
- 7.5.2.3 Workstation Checklist
- 7.5.2.4 NIC Configuration Checklist
- 7.5.2.5 Printer Server/File Server/Printer Checklist
- 7.5.2.6 Workstation to NIC Connection Checklist
- 7.5.2.7 NIC Loses Its File Server Connection
- 7.5.2.8 Unable to Print from a Different Context
- 7.5.3 Troubleshooting AppleTalk Protocol
- App.A Jumper Settings
- App.B Specifications
- App.C Using a Web Browser
- App.D Index
![](/manual/minolta/18n/network-card-user-manual/images/img-140.png)
7.3 Resetting the NIC to Factory Default
7-5
Operation and Troubleshooting
Chapter 7
7.3 Resetting the NIC to Factory Default
You can cause the NIC to restore all parameters to factory default
values, so the NIC appears just as it came from the factory. You may
choose to do this when the NIC is moved to a new location where the
environment (NetWare file servers, IP subnets, and so on) is different.
This process is called “Reset to Factory”. It can be done with the
standard Telnet or Web pages (accessed via MAP or a Web Browser)
utility. However, if network access is not possible, the following
method may be used.
Note
To reset the NIC:
1. Power off the printer and remove the NIC from the printer. The
removal process is the reverse of the installation process in Quick
Guide for Installation and Reference.
2. Locate the Reset Jumper. It is labeled OP2. See diagram in Appendix A.
3. Move this jumper to the ON position, so that the jumper covers the
center pin and the pin nearest the jumper designator.
4. Install the NIC as shown in Quick Guide for Installation and Ref-
erence. Do not connect the printer to the network.
5. Power on the printer. The NIC performs its diagnostic self tests —
the green LED blinks 3 times then goes into an alternating green/
amber light sequence. When you see this pattern, power off the
printer.
6. Remove the NIC from the printer.
7. Move the OP2 jumper to its OFF position, so that the jumper cov-
ers the center pin and the pin nearest the OFF designation.
8. Reinstall the NIC according to Quick Guide for Installation and
Reference.
• Resetting to factory default means that the print server loses all data
such as names and IP addresses. It does not lose its serial number and
MAC Address.
Chap7.fm Page 5 Monday, August 17, 1998 10:06 AM