PROGRAM FLASH MAXXUM FLASH 5600HS (D) G BEDIENUNGSANLEITUNG
SICHERHEITSHINWEISE Bevor Sie dieses Produkt in Gebrauch nehmen, lesen und beachten Sie bitte die folgenden Sicherheitshinweise. Hinweis Batterien können bei unsachgemäßem Gebrauch explodieren. • Benutzen Sie nur Batterien des in dieser Bedienungsanleitung angegebenen Typs. • Achten Sie beim Einsetzen der Batterien auf richtige Polarität. • Setzen Sie Batterien niemals Feuer oder hohen Temperaturen aus. • Versuchen Sie nie, Einwegbatterien aufzuladen, kurzzuschließen oder zu zerlegen.
Achtung Berühren Sie die Blitzleuchte nicht während des Blitzbetriebes. Batterien und wiederaufladbare Akkus gehören nicht in den Hausmüll ! Jeder Endverbraucher ist im Interesse des Umweltschutzes und per Batterieverordnung verpflichtet, Batterien und wiederaufladbare Akkus zurückzugeben. Die verbrauchten Batterien können an die öffentlichen Sammelstellen oder an den Verkäufer der entsprechenden Batterien zurückgegeben werden. Die Rücknahme erfolgt unentgeltlich.
INHALTSVERZEICHNIS KAMERAS UND BLITZEINHEITEN ........................................................6 BEZEICHNUNG DER TEILE...................................................................8 GRUNDLAGEN DER BEDIENUNG EINSETZEN DER BATTERIEN.............................................................12 Prüfen der Batterieleistung ..........................................................13 MONTIEREN UND ABNEHMEN DES BLITZGERÄTES ......................14 EIN-/AUSSCHALTEN DES BLITZGERÄTES...................
EINSTELLEN DER LEISTUNGSWAHL (LEVEL)..................................58 STROBOSKOPISCHES BLITZEN (MULTI) ..........................................60 ZURÜCKSETZEN AUF DIE STANDARDEINSTELLUNGEN................64 CUSTOM-FUNKTION............................................................................
KAMERAS UND BLITZEINHEITEN Kameras Diese Bedienungsanleitung behandelt den Gebrauch des Programm-Blitzgerätes 5600HS (D) in Verbindung mit einer der folgenden Kameras.
Diese Blitzeinheit wurde eigens für die Verwendung in Verbindung mit Kameras der Dynax/Dimage-Serie von Konica Minolta hergestellt. An andere Konica Minolta-Kameras kann es nicht montiert werden. Die Leistungsfähigkeit kann nicht garantiert werden, wenn diese Blitzeinheit in Verbindung mit Kameras anderer Hersteller verwendet wird. Konica Minolta übernimmt in diesem Fall keine Haftung für Schäden oder Fehlfunktionen der Blitzeinheit.
BEZEICHNUNG DER TEILE Blitzeinheit Schutzfolie auf der Vorderseite des Blitzes.
Bedienfeld Taste – Select-Taste Mode-Taste Taste + Datenfeldbeleuchtung (32) Handauslösetaste (Testblitz) (26) / Handauslösetaste (Blitz-Einstellicht) (26) Ein-/Aus-Taste (15) Blitzbereitschaftsanzeige (17) Drehschalter zur Auswahl der Testblitzart/HOLD (26) Taste ZOOM (Ausleuchtwinkel) (24) 9
BEZEICHNUNG DER TEILE Datenfeld Steueranzeige für drahtloses Blitzen (48) Warnanzeige für Blitzbereich (18) Anzeige High-SpeedSynchronisation (38) Anzeige für drahtloses Blitzen (46-54) OK-Signal für ausreichende Blitzbelichtung (17) Anzeige für TTLBlitzautomatik (36) Anzeige für manuelle Blitzsteuerung (36) Anzeige für stroboskopisches Blitzen (60) Anzeige für CustomFunktion (65) Anzeige für Verhältnissteuerung (50, 53, 56) Anzeige der Leistungsstufe (58) Anzeige Blitzbereich (18)/ Blitzfrequenz (60)
GRUNDLAGEN DER BEDIENUNG Bitte lesen Sie diesen Abschnitt sorgfältig durch, bevor Sie das Programm-Blitzgerät 5600HS (D) benutzen. In diesem Teil finden Sie die wichtigsten Bedienungshinweise, um das Programm-Blitzgerät möglichst schnell benutzen zu können. • In der Blitzautomatik wird nur bei Bedarf ein Blitz gezündet. In der Funktion „Manuelles Aufhellblitzen“ wird der Blitz, unabhängig vom Umgebungslicht, bei jeder Aufnahme gezündet.
EINSETZEN DER BATTERIEN Das Programm-Blitzgerät 5600HS (D) bezieht seine elektrische Energie wahlweise aus • vier Alkali-Mangan Batterien des Typs AA • vier Lithium Batterien des Typs AA • vier wiederaufladbaren NiMH Batterien des Typs AA Laden Sie wiederaufladbare NiMH Batterien immer in einer speziellen Aufladeeinheit auf. 1. Öffnen Sie den Batteriekammerdeckel wie gezeigt. 2. Batterien polrichtig (siehe Aufkleber im Batteriefach) einsetzen. 3. Schließen Sie den Batteriekammerdeckel.
Bei schwacher Batterie erscheint das Symbol im Datenfeld. Wir empfehlen Ihnen, die Batterien zu ersetzen. Batteriespannung ist zu niedrig für einwandfreie Funktion. Batterien müssen sofort ersetzt werden. • Prüfen Sie, ob die Batterien richtig eingesetzt sind, wenn bei gedrückter Ein-/Aus-Taste keine Anzeige im Datenfeld erscheint.
MONTIEREN UND ABNEHMEN DES BLITZGERÄTES Montieren Aufsteckfuß des Blitzgeräts bis zum Einrasten auf die Kamera aufstecken. • Das Blitzgerät wird automatisch verriegelt. • Ist das eingebaute Blitzgerät an der Kamera aufgeklappt, drücken Sie es herunter, bevor Sie die Blitzeinheit montieren. Abnehmen Aufsteckfuß-Entriegelung gedrückt halten und Blitzgerät abnehmen.
EIN-/AUSSCHALTEN DES BLITZGERÄTES VORBEREITUNG Einschalten des Blitzgerätes Die Blitzeinheit wird in folgenden Situationen automatisch eingeschaltet: • Wenn das Programm-Blitzgerät an der Kamera montiert ist, wird mit dem Einschalten der Kamera auch das Blitzgerät eingeschaltet (automatische Einschaltung). • Durch Drücken der Ein-/Aus-Taste kann das Blitzgerät eingeschaltet werden.
BLITZ-PROGRAMMAUTOMATIK (P-FUNKTION): DIE GRUNDLAGEN 1. Stellen Sie an der Kamera die P-Funktion ein. 2. Drücken Sie die Ein-/Aus-Taste, um oder anzuzeigen. 3. Drücken Sie den Auslöser leicht an. • In der Blitzautomatik erscheint und . Bei manuellem Aufhellblitz erscheint nur . • In Verbindung mit der Dynax 7 wird im Vollautomatik-Betrieb die Blitzautomatik und in der Programmautomatik (P-Funktion) manuelles Aufhellblitzen verwendet.
• Detaillierte Hinweise zum Blitzbereich finden Sie auf Seite 18. 5. Warten Sie, bis das Blitzgerät aufgeladen ist, und drücken Sie den Auslöser ganz durch, um die Aufnahme zu machen. • Blitzbereitschaft besteht, wenn das Symbol an der Rückseite des Blitzgeräts und im Sucher der Kamera aufleuchtet. Wenn die abgegebene Blitzlichtmenge für eine korrekte Belichtung ausreichend war, • wird auf dem Datenfeld des Blitzgerätes für etwa 4 Sekunden angezeigt und • blinkt im Sucher der Kamera.
BLITZ-PROGRAMMAUTOMATIK (P-FUNKTION): DIE GRUNDLAGEN Blitzbereich Drücken Sie den Auslöser leicht an, um den Blitzbereich für die ideale Belichtung Ihrer Aufnahme auf dem Datenfeld anzuzeigen. Vergewissern Sie sich, daß sich Ihr Objekt in dieser Reichweite befindet und machen Sie die Aufnahme. Die Blitzbereichsanzeige auf dem Datenfeld gibt den Bereich an, innerhalb dessen eine korrekte Belichtung erzielt werden kann. Die Entfernungswerte betragen 1,5m – 28m (für Nahaufnahmen 0,7m – 28m, siehe S. 31).
Diese Anwendung ist nur mit Kameras möglich, die über A-, S- und M-Funktion verfügen. Blitz-Zeitautomatik (A-Funktion) Stellen Sie die A-Funktion an der Kamera ein. 2. Drücken Sie die Ein-/Aus-Taste um anzuzeigen. • Manuelles Aufhellblitzen ist gewählt. 3. Wählen Sie die Blende und nehmen Sie Ihr Objekt in den Autofokus-Rahmen.
BLITZ-BELICHTUNGSFUNKTIONEN Blitzautomatik in M-Funktion 1. Stellen Sie die M-Funktion an der Kamera ein. 2. Drücken Sie die Ein-/Aus-Taste um anzuzeigen. • Manuelles Aufhellblitzen ist gewählt. 3. Wählen Sie die Blende und Verschlußzeit und nehmen Sie Ihr Objekt in den Autofokus-Rahmen. • Verringern Sie die Blitzreichweite, indem Sie eine kleinere Blende (größeren Blendenwert) wählen, oder vergrößern sie die Blitzreichweite, indem Sie eine größere Blende (kleineren Blendenwert) wählen.
In der Blitzlicht-Fotografie kann die Verschlußzeit im allgemeinen nicht kürzer sein als die kürzeste Blitzsynchronzeit. Diese Einschränkung gilt nicht für Kameras mit High-SpeedSynchronisation (HSS), weil diese in der Blitzlicht-Fotografie jede verfügbafe Verschlußzeit der Kamera zulassen.
ANWENDUNGEN Dieser Abschnitt beschreibt im Detail die verschiedenen Verfahrensweisen zur vollen Ausnutzung der Blitzeinheit.
ZOOMREFLEKTOR (Blitzausleuchtung) Autozoom 85mm Objektivbrennweite • Drücken Sie den Auslöser leicht an, um die Zoomeinstellung des automatischen Blitzreflektors auf dem Datenfeld anzuzeigen.
ZOOMREFLEKTOR (Blitzausleuchtung) Manuelle Zoomeinstellung Der Ausleuchtwinkel kann unabhängig von der aktuell verwendeten Objektivbrennweite manuell eingestellt werden. Drücken Sie die Taste ZOOM, um die gewünschte Zoomeinstellung anzuzeigen. • Durch wiederholtes Drücken dieser Taste wird die ZoomreflektorEinstellung verändert. Autozoom, 24mm, 28mm, 35mm, 50mm, 70mm, 85mm • [M.ZOOM] wird über der ZoomreflektorEinstellung angezeigt, wenn die Zoomeinstellung manuell erfolgt.
Eingebauter Weitwinkeladapter (für 17mm Brennweite) Ziehen Sie den eingebauten Weitwinkeladapter mit einem maximalen Ausleuchtwinkel für 17 mm Brennweite heraus. • Im Datenfeld wird der Ausleuchtwinkel [17mm] und der Blitzbereich angezeigt. • Beim Fotografieren von flächigen Motiven kommt es insbesondere bei der Verwendung von Super-Weitwinkelobjektiven, wie z.B. AF 3,5/1735mm G, zu einem Randlichtabfall. Dieser ist physikalisch bedingt und stellt keinen technischen Mangel dar.
TESTBLITZ/BLITZ-EINSTELLICHT Zum Überprüfen des Blitzbetriebs können mehrere Testblitze gezündet werden. Dies ist vor allem dann sinnvoll, wenn in der drahtlosen Blitzfernsteuerung das Blitzgerät von der Kamera getrennt ist, um die Lichtführung zu beurteilen. * Im Standart-Blitzbetrieb und in der drahtlosen Blitzfernsteuerung kann das Blitz-Einstellicht zum Beurteilen der Lichtführung eingesetzt werden, bevor die Auslösung erfolgt. 1.
• Drücken Sie nicht auf den Auslöser, während das Blitzgerät arbeitet. • Die Stärke der Schattenbildung weicht von der in der eigentlichen Aufnahme ab. • Die Schattenbildung ist geringer bei indirektem Blitzen oder wenn in hellen Bereichen oder bei Tageslicht geblitzt wird. Die Überprüfung ist in diesen Fällen schwieriger. 27 TESTBLITZ BLITZ-EINSTELLICHT 2. Drücken Sie die Handauslösetaste (Testblitz und Blitz-Einstellicht), wenn das Blitzgerät voll aufgeladen ist.
INDIREKTES BLITZEN Wenn das Blitzlicht über eine nahe Reflexionsfläche zum Objekt reflektiert wird, ergibt sich eine weichere Ausleuchtung als beim direkten Blitzen. Der Reflektorkopf des 5600HS (D) läßt sich bis 90° nach oben schwenken, 90° nach rechts und 180° nach links drehen. Indirektes Blitzen Normales Blitzen Schwenken Sie bei gedrückter Entriegelungstaste den Reflektorkopf in die gewünschte Stellung.
Der Blitzkopf besitzt folgende Rasteinstellungen: • • • • Vertikal nach oben: 45°, 60°, 75°, 90° Vertikal nach unten: 10° (siehe „Nah- und Makrofotografie“ auf Seite 31) Drehen im Uhrzeigersinn: 30°, 45°, 60°, 75°, 90° Drehen entgegen den Uhrzeigersinn: 30°, 45°, 60°, 75°, 90°, 120°, 150°, 180° • Die Sperre kuppelt in Nullposition ein. Die Entriegelungstaste muß nicht gedrückt werden, wenn der Reflektorkopf in seine Ausgangsstellung zurückgeschwenkt wird.
INDIREKTES BLITZEN Einstellwinkel des Reflektorkopfes Der Reflektorkopf sollte so ausgerichtet werden, daß kein direktes Licht zum Objekt gelangt, was eine ungleichmäßige Ausleuchtung ergäbe. Der ideale Reflektorwinkel ist abhängig von der Entfernung des Blitzgerätes zur Reflexionsfläche, dem Abstand zwischen Kamera und Objekt und der Objektivbrennweite. Richtig Falsch Die Tabelle zeigt einige empfehlenswerte Reflektorwinkel mit senkrecht geschwenktem Reflektor zum indirekten Blitzen.
NAH- UND MAKROFOTOGRAFIE Für Nah- und Makroaufnahmen mit einer Nahgrenze von 0,7m bis 1,5m läßt sich der Blitzreflektor nach unten schwenken. NAH- UND MAKROFOTOGRAFIE Schwenken Sie den Blitzkopf bei gedrückter Entriegelungstaste vertikal nach unten. • Die Anzeige für indirektes Blitzen erscheint im Datenfeld. • Der Reflektorwinkel beträgt 10°. • Bei Entfernungen unter 0,7m ist eine Ausleuchtung des gesamten Objekts nicht möglich, so daß der untere Bildrand abgeschattet ist.
DATENFELDBELEUCHTUNG Zur besseren Übersicht bei schwachem Licht kann das Datenfeld beleuchtet werden. Drücken Sie die Taste für die Datenfeldbeleuchtung. • Das Datenfeld wird ca. 8 Sekunden beleuchtet. Wird das Blitzgerät während dieser Zeit betätigt, verlängert sich die Beleuchtungszeit. • Drücken Sie die Taste erneut, um die Datenfeldbeleuchtung auszuschalten.
AF-BELEUCHTUNGSGERÄT • Das AF-Beleuchtungsgerät arbeitet unter Verwendung der Einzelsensoren mit allen Kameras, die über ein großes AF-Meßfeld verfügen. • Das AF-Beleuchtungsgerät arbeitet auch bei abgeschaltetem Blitzgerät. • Wird das Programm-Blitzgerät direkt auf die Kamera montiert wird statt des Beleuchtungsgeräts der Kamera dessen AFBeleuchtungsgerät aktiv. • Im Nachführ-Autofokus arbeitet das AF-Beleuchtungsgerät nicht.
FUNKTIONSTASTEN Die Tasten Mode, Select, + und – werden dazu benutzt, um die auf der nächsten Seite beschriebenen Funktionen zu wählen. Die Funktionen werden mit dem folgenden Grundverfahren gewählt. Darüber hinausgehende Angaben finden Sie auf den entsprechenden Seiten. 1. Wählen Sie den Hauptpunkt mit der Mode-Taste. 2. Wählen Sie den Unterpunkt mit der Select-Taste. 3. Nehmen Sie die Einstellungen mit den Tasten + und – vor. 4. Drücken Sie wiederholt die Select-Taste*, bis das Blinken aufhört.
Wahl mit der Wahl mit den Tasten + und – (die Posten in Select-Taste Kursivschrift sind Ausgangseinstellungen) HSS (38) ON, OFF WL (40) TTL (36) RATIO M (36) OFF, , LEVEL (58) 1/1, 1/2, 1/4, 1/8, 1/16, 1/32 HSS (38) ON, OFF WL (40) OFF, ON LEVEL (58) 1/1, 1/2, 1/4, 1/8, 1/16, 1/32 100, 50, 40, 30, 20, 10, 9, 8, 7 ,6, 5, 4, 3, 2 - - (unbegrenzt), 40, 35, 30, 25, 20, 15, 10, 9, 8, 7, 6, 5, 4, 3, 2 1/8, 1/16, 1/32 Hz MULTI (60) OFF, ON, CONTROL TIME LEVEL Nähere Angaben finden Sie auf den in K
MANUELLER BLITZBETRIEB (M) In der TTL-Blitzautomatik wird die abgegebene Lichtmenge durch das Objektiv vom Belichtungsmeßsystem der Kamera bewertet und entsprechend gesteuert. Im manuellen Blitzbetrieb wird die Blitzleistung nicht vom Belichtungssystem gesteuert, sondern mit voller Leistung geblitzt. Die richtige Belichtung hängt in diesem Fall von der manuell eingestellten Blende, dem Objektabstand und der Leistungsstufe des Blitzgerätes ab.
3. Drücken Sie die Taste + oder –, um die Leistungsstufe zu wählen. • Der für die ideale Blitzbelichtung geeignete Objektabstand wird bei leicht angedrücktem Auslöser im Datenfeld angezeigt. Korrekte Belichtung ist gewährleistet unter 1,5m. Korrekte Belichtung ist gewährleistet bei 28m oder darüber. • Das Signal für ausreichende Blitzbelichtung wird im manuellen Blitzbetrieb nicht angezeigt. • Die ADI- und Vorblitzmessung ist in Verbindung mit einigen Kamera/Blitz/Objektiv-Kombinationen möglich.
HIGH-SPEED-SYNCHRONISATION (HSS) Mit HSS Ohne HSS Die High-Speed-Synchronisation erlaubt es, zum Blitzen jede beliebige Verschlußzeit der Kamera zu verwenden. Der zur Verfügung stehende Blendenbereich hat sich erweitert, so daß bei geblitzten Porträtaufnahmen größere Blendenöffnungen benutzt werden können, um eine schöne Trennung zwischen Porträt und unscharfem Hintergrund zu erreichen. • Die Kurzzeit-Blitzsynchronisation kann mit einigen Kameramodellen (siehe Seite 21) genutzt werden. 1.
mit der Taste + 4. Drücken Sie wiederholt die Select-Taste, bis das Blinken stoppt. • Im Datenfeld bleibt [HSS] stehen. • Durch Wählen von mit der Taste + oder – wird die HSS-Funktion gelöscht und eine kürzere Verschlußzeit als die Blitzsynchronzeit kann nicht mehr eingestellt werden. • Bei dunklem Umgebungslicht kann die HSS-Funktion nicht eingesetzt werden. In diesem Fall kann die Verschlußzeit nicht kürzer als die Blitzsynchronzeit sein.
DRAHTLOSE TTL-BLITZFERNS- Normales Blitzen Drahtlose Blitzfernsteuerung Blitzverhältnissteuerung 40 Blitzaufnahmen mit dem an der Kamera montierten Blitzgerät wirken oft flach, wie in Bild gezeigt. Nehmen Sie in diesem Fall das Blitzgerät von der Kamera ab und positionieren Sie es so, daß ein plastisches Bild, wie in Foto gezeigt, entsteht.
Verschiedene Möglichkeiten der drahtlosen Blitzfernsteuerung Die folgenden drei Arten der drahtlosen Blitzfernsteuerung sind möglich. Die folgenden zwei Funktionen stehen zur Verfügung: • Verwenden Sie nur eine externe Blitzeinheit (Foto , S. 40). • Verwenden Sie das eingebaute Blitzgerät zur Steuerung einer externen Blitzeinheit mit einem Beleuchtungsverhältnis von beispielsweise 1:2 (Foto , S. 40). Geeignete Kameras und Blitzeinheiten: • Jede Kamera auf Seite 6, außer DiMAGE Z2, Z1, 7, 5, und Dynax 40.
DRAHTLOSE TTL-BLITZFERNSTEUERUNG [3] Verwendung des drahtlosen Fernsteuerungsgerätes (S. 52) Die folgenden zwei Funktionen stehen zur Verfügung: • Verwenden Sie ein externes Blitzgerät (Foto , S. 40). • Verwenden Sie zwei externe Blitzgeräte mit einem Beleuchtungsverhältnis von 1:2 oder 2:1. Geeignete Kameras und Blitzeinheiten: • Dynax 9, 7, 800si, 700si oder 600si. • Ein drahtloses Fernsteuerungsgerät in Verbindung mit einem oder mehreren 5600HS (D), 3600HS (D), 5400HS, 5400xi oder 3500xi.
Entfernung zwischen Kamera und Motiv (siehe Tabelle 1) Entfernung zwischen 5600HS (D) und Motiv (siehe Tabelle 2) Ist das externe Blitzgerät hinter dem Objekt paziert, kann es u.U. die Steuersignale nicht empfangen. KameraObjektabstand (Tabelle 1) 5600HS (D)-Objektabstand (Tabelle 2) Ohne HSS Mit HSS Verschluß Alle 1/60Max. 1/200 -zeit Verschluß- 1/60Sek. zeiten Sek. Blende 1/250 Sek. 1/500 1/1000 1/2000 1/4000 Sek. Sek. Sek. Sek.
DRAHTLOSE TTL-BLITZFERNSTEUERUNG Hinweise zur drahtlosen Blitzfernsteuerung • Befestigen Sie den beigefügten Blitzgeräteständer MS-2 an Ihrem Blitzgerät wie in der Zeichnung gezeigt. Der Blitzgeräteständer MS-2 verfügt auf der Unterseite über ein Stativgewinde, um das Blitzgerät auch an einem Stativ befestigen zu können. Befestigen Entfernen • Weil in der drahtlosen Blitzfernsteuerung ein Vorblitz gezündet wird, kann ein Flash Meter und Color Meter nicht verwendet werden.
DRAHTLOSE BLITZFERNSTEUERUNG • Stroboskopisches Blitzen ist nicht anwendbar. • Damit mehrere Fotografen am gleichen Ort drahtlos Blitzen können, ohne sich gegenseitig zu stören, stehen verschiedene Kanäle zur Verfügung, die durch Einstellung in den Custom-Funktionen gewechselt werden können (S. 65).
DRAHTLOSE TTL-BLITZFERNSTEUERUNG [1]-1 Verwendung des eingebauten Blitzgerätes 1. Programm-Blitzgerät 5600HS (D) auf der Kamera montieren und beide Geräte einschalten. 2. Stellen Sie die Kamera auf drahtloses Blitzen ein (siehe Bedienungsanleitung zur Kamera). • Das 5600HS (D) ist gleichzeitig mit der Kamera automatisch auf drahtloses Blitzen eingestellt und im Datenfeld wird WL angezeigt. 3. Nehmen Sie das ProgrammBlitzgerät ab und klappen Sie das eingebaute Blitzgerät der Kamera auf. 4.
6. Zünden Sie einen Testblitz, um sicherzustellen, daß das 5600HS (D) richtig funktioniert. • Die Methode, einen Testblitz zu zünden variiert je nach Kameratyp (Drücken der AEL-Taste oder der Spot-Taste). Lesen Sie die Bedienungsanleitung zur Kamera. 7. Warten Sie, bis beide Blitzgeräte wieder voll aufgeladen sind und drücken Sie den Auslöser für die Aufnahme. Das Beleuchtungsverhältnis 1:2 kann auch in Verbindung mit der drahtlosen Blitzfernsteuerung gesteuert werden.
DRAHTLOSE TTL-BLITZFERNSTEUERUNG [2]-1 Verwendung von zwei Blitzeinheiten • Es können entweder zwei 5600HS (D), 5400HS, 5400xi oder ein 5600HS (D), 5400HS, 5400xi mit einem 3600HS (D) oder 3500xi benutzt werden. • Als Kamera kann die Dynax 9, 7, 800si, 700si oder 600si verwendet werden. Bei Verwendung von zwei Blitzgeräten kann das an der Kamera montierte Blitzgerät als Steuergerät für das externe Blitzgerät zum drahtlosen Blitzen eingesetzt werden.
5. Drücken Sie die Select-Taste so oft, bis das Blinken stoppt. 6. Montieren Sie das 5600HS (D) auf der Kamera. • Als Steuer-Blitzgerät kann auch das Programm-Blitzgerät 5400HS oder 5400xi eingesetzt werden. Lesen Sie die Bedienungsanleitung zur 5400HS. Bei Verwendung des 5400xi steht im Display [W.L-C.1]. Einrichten des externen Blitzgeräts 1. Schalten Sie das 5600HS (D) ein. 2. Drücken Sie die Mode-Taste, um oder im Datenfeld anzuzeigen. 3. Drücken Sie die Select-Taste so oft, bis [WL] blinkt. 4.
DRAHTLOSE TTL-BLITZFERNSTEUERUNG Fotografieren 1. Richten Sie die Kamera mit einem Steuer-Blitzgerät und einer externen Blitzeinheit ein. • Beachten Sie die Angaben auf Seite 43. • Wird das Programm-Blitzgerät 5600HS (D) als Steuergerät und eine andere Blitzeinheit als die aus der D-Serie (siehe S. 6) als externes Blitzgerät benutzt, beachten Sie, daß keine kürzere Verschlußzeit als die kürzeste Blitzsynchronzeit der Kamera eingestellt werden kann, da das externe Blitzgerät sonst nicht arbeiten würde. 2.
Einrichten des Steuer-Blitzgeräts (Folgende Verfahrensweise gilt, wenn das 5600HS (D) als Steuergerät eingesetzt wird.) 1. Richten Sie das Programm-Blitzgerät 5600HS (D) wie auf Seite 48 beschrieben ein. DRAHTLOSE BLITZFERNSTEUERUNG 2. Drücken Sie die Select-Taste, bis im Datenfeld [RATIO] blinkt. 3. Wählen Sie mit der Taste + oder – . 4. Drücken Sie die Select-Taste. 5. Montieren Sie das 5600HS (D) auf der Kamera.
DRAHTLOSE TTL-BLITZFERNSTEUERUNG [3]-1 Verwendung des drahtlosen Fernsteuerungsgeräts • Erforderlich ist das drahtlose Fernsteuerungsgerät und wenigstens ein externes Blitzgerät. Als externe Blitzgeräte können wahlweise das 5600HS (D), 3600HS (D), 5400HS, 5400xi oder 3500xi verwendet werden. • Benutzen Sie als Kamera die Dynax 9, 7, 800si, 700si oder 600si. Die Dynax 7 und das Programm-Blitzgerät 5600HS (D) sind in der Bedienungsanleitung zum drahtlosen Fernsteuerungsgerät u.U. noch nicht erwähnt.
3. Drücken Sie die Select-Taste so lange, bis [WL] blinkt. 4. Drücken Sie die Taste + oder –, bis [WL On] blinkt. 5. Drücken Sie die Select-Taste, bis das Blinken stoppt. Lesen Sie die Bedienungsanleitung zum drahtlosen Fernsteuerungsgerät. • Verwenden Sie eine Verschlußzeit von 1/60s oder länger (lange Verschlußzeit). Die High-Speed-Synchronisation (HSS) kann nicht benutzt werden.
DRAHTLOSE TTL-BLITZFERNSTEUERUNG 2. Drücken Sie die Select-Taste so lange, bis [RATIO] blinkt. 3. Entscheiden Sie, welches externe Blitzgerät die Hauptbeleuchtung übernehmen soll, und wählen Sie mit der Taste + oder – die entsprechende Einstellung. • Das Blitzgerät mit der Einstellung übernimmt 1/3 der Gesamtbeleuchtung, während das Blitzgerät mit der Einstellung die Hauptbeleuchtung (2/3 der Gesamtbeleuchtung) übernimmt. • Richten Sie nicht beide Blitzgeräte mit der gleichen Einstellung aus.
VERBINDEN VON KAMERA UND BLITZGERÄT ÜBER KABEL • Blitzeinheiten, die über eine Zubehöranschlußbuchse verfügen, können direkt angeschlossen werden. Zum Verbinden des 5600HS (D) entfernen Sie die Anschlußbuchsenabdeckung und stecken Sie das Verbindungskabel in die Zubehöranschlußbuchse. Blitzeinheiten Folgende Blitzeinheiten können von der Kamera getrennt und über Kabel verbunden verwendet werden.
VERBINDEN VON KAMERA UND BLITZGERÄT ÜBER KABEL Angleichen der Leistungswahl aller Blitzeinheiten Alle Blitzeinheiten der Gruppe A und B können verwendet werden. 1. Stellen Sie die notwendigen Kabelverbindungen zwischen den Blitzeinheiten her. 2. Schalten Sie alle Blitzeinheiten ein. 3. Machen Sie die Aufnahme.
1. Stellen Sie die notwendigen Kabelverbindungen zwischen den Blitzeinheiten her. 2. Schalten Sie alle Blitzeinheiten ein. 4. Drücken Sie die Select-Taste so lange, bis [RATIO] blinkt. 5. Wählen Sie mit der Taste + oder – das Beleuchtungsverhältnis oder . • Bei der Verhältnissteuerung wird 1/3 der Gesamtbeleuchtung vom 5600HS (D) übernommen, bei Einstellung beträgt der Blitzlichtanteil 2/3 der Gesamtbeleuchtung. • Der restliche Blitzlichtanteil wird von den anderen Blitzgeräten übernommen. 6.
EINSTELLEN DER LEISTUNGSWAHL (LEVEL) Die Blitzleistung des Blitzgerätes kann in insgesamt 6 Stufen gewählt werden. 1. Drücken Sie die Select-Taste, um [LEVEL] im Datenfeld anzuzeigen. • Die aktuell eingestellte Leistungsstufe wird angezeigt. • Dieser Punkt kann ignoriert werden, wenn sich das Blitzgerät im manuellen Blitzbetrieb befindet. 2. Wählen Sie mit der Taste + oder – die gewünschte Leistungsstufe.
LEISTUNGSWAHL • Der im Display angezeigte Objektabstand ändert sich entsprechend der eingestellten Leistungsstufe. • Die Leistungswahl kann unabhängig von den Funktionen , , erfolgen. Das Blitzgerät merkt sich die Einstellung für jede Funktion, so daß sie beim Umschalten erhalten bleibt. • Im TTL-Blitzbetrieb wird automatisch die höchste Leistungsstufe eingestellt.
STROBOSKOPISCHES BLITZEN (MULTI) Bei dieser Funktion werden mehrere aufeinanderfolgende Blitze abgegeben. Die Blitzfrequenz und die Anzahl der Blitze kann manuell eingestellt werden. Mit dieser Funktion kann man mehrere Blitzbelichtungen auf ein einziges Bildfeld machen. Dies ist besonders interessant bei Bewegungsstudien. • Stellen Sie Ihre Kamera auf manuelle Belichtungsfunktion (M). In anderen Belichtungsfunktionen ist das Stroboskopische Blitzen nicht möglich. 1.
4. Wählen sie mit der Taste + oder – die gewünschte Blitzfrequenz. 5. Drücken Sie die Select-Taste, bis [TIMES] blinkt. • Die aktuelle Anzahl der Blitze wird im Datenfeld angezeigt. 6. Wählen Sie mit der Taste + oder –, wie oft geblitzt werden soll. • Folgende Blitzanzahl kann gewählt werden: --, 40, 35, 30, 25, 20, 15, 10, 9, 8, 7, 6, 5, 4, 3, 2 • Um die Werte schnell zu durchlaufen, halten Sie die Taste + oder – gedrückt.
STROBOSKOPISCHES BLITZEN (MULTI) 7. Drücken sie die Select-Taste, bis [LEVEL] im Datenfeld blinkt. • Die aktuelle Leistungsstufe wird angezeigt. 8. Wählen Sie mit der Taste + oder – die gewünschte Leistungsstufe. • Es können die Leistungsstufen 1/8, 1/16 und 1/32 gewählt werden. 9. Drücken Sie die Select-Taste. 10. Stellen Sie die Verschlußzeit und Blende ein. • Die Verschlußzeit muß immer so gewählt werden, daß die Blitzsequenz innerhalb dieser Zeit abgegeben werden kann.
• Um Verwacklungsunschärfen wegen der längeren Verschlußzeiten zu vermeiden, wird empfohlen, die Kamera auf ein Stativ zu montieren. • Auf Stellung oder HOLD wird mit gedrückter Handauslösetaste ein Testblitz mit den Einstellungen für Blitzfrequenz/Blitzanzahl/ Leistungswahl gezündet. • Die Custom-Funktionen erlauben den manuellen Blitzbetrieb, ohne daß die Kamera auf manuelle Belichtungsfunktion (M) gestellt werden muß (S. 66).
ZURÜCKSETZEN AUF DIE STANDARDEINSTELLUNGEN Wenn die Tasten + und – gleichzeitig 3 Sekunden lang gedrückt gehalten werden, werden die meisten Blitzfunktionen auf ihre Grundeinstellungen zurückgesetzt. Funktion Grundeinstellung Seite Ein-/Ausschaltung des Blitzgeräts Ein (autom.
Die Custom-Funktionen erlauben es, das Blitzgerät den speziellen fotografischen Wünschen anzupassen.
CUSTOM-FUNKTIONEN Auswahl mit der Taste + oder – 1. Kanalwahl für die drahtlose TTL-Blitzfernsteuerung Kanal 1 Kanal 2 Kanal 3 Kanal 4 Auswahl mit der Select-Taste 2. Bereichsanzeige im Datenmonitor (Meter/Feet) m ft 3. Dauer des Standby-Betriebs bis zur automatischen Abschaltung 4 Minuten 15 Minuten 60 Minuten dauerhaft eingeschaltet 4. Dauer des Standby-Betriebs bis zur automatischen Abschaltung im drahtlosen TTL-Blitzbetrieb 60 Minuten dauerhaft eingeschaltet 5.
3. Drücken Sie die Mode-Taste. • Nach dem Einstellen des Kanals (siehe 1. Kanalwahl für die drahtlose TTL-Blitzfernsteuerung) muß das Blitzgerät erst wieder auf der Kamera montiert werden. Drücken Sie danach den Auslöser leicht an, um die Information an die Kamera zu übermitteln. • Wenn "Alle Funktionen" gewählt wurde (siehe 5.
ANHANG 68
VERWENDUNG IN VERBINDUNG MIT ANDEREN PRODUKTEN Bitte lesen Sie bei der Verwendung von anderem Systemzubehör die jeweilige Bedienungsanleitung parallel zur Anleitung des 5600HS (D). Verwendung von SLR-Kameras der xi-Serie: • In der Progammautomatik erfolgt die Blitzzuschaltung automatisch (9xi, 7xi, 5xi und 3xi). Manuelles Aufhellblitzen ist jederzeit möglich. Für Details schauen Sie bitte in die Bedienungsanleitung zur Kamera. • In der Progammautomatik erfolgt die Blitzzuschaltung automatisch (2xi, SPxi).
VERWENDUNG IN VERBINDUNG MIT ANDEREN PRODUKTEN Verwendung von SLR-Kameras der i-Serie: (Dynax 8000i, 7000i, 5000i, 3000i) • In der Progammautomatik erfolgt die Blitzzuschaltung automatisch. Manuelles Aufhellblitzen ist nur mit der Dynax 8000i möglich. Für Details schauen Sie bitte in die Bedienungsanleitung zur Kamera. • In der S-Funktion (Blendenautomatik) erfolgt die Blitzzuschaltung automatisch. Die Verschlußzeit wird ebenfalls automatisch gesteuert.
Verwendung von SLR-Digital-Kameras (Dimâge RD-3000 und RD-175) VERBINDUNG MIT ANDEREN PRODUKTEN • In der Progammautomatik erfolgt die Blitzzuschaltung automatisch. Manuelles Aufhellblitzen ist jederzeit möglich. • Die Verschlußzeit wird auch in der S-Funktion (Blendenautomatik) automatisch eingestellt. • Die HSS-Funktion kann mit diesen Kameras nicht genutzt werden.
ZUBEHÖR Blitzkabel und dazu passendes Zubehör • Verbindungskabel OC-1100 • Anschlußschuh OS-1100 • Verlängerungskabel EX • Verbindungskabel CD • Dreifachanschluß TC-1000 Die Blitzkabel und das passende Zubehör werden immer dann benötigt, wenn die drahtlose TTL-Blitzfernsteuerung nicht möglich ist. Alle aufgeführten Kabel sind Spiralkabel und im ausgezogenen Zustand maximal 1 m lang. Mit einem Verlängerungskabel EX kann jede Kabelverbindung um jeweils 1 m verlängert werden.
Reflexschirm V (Set) Dieses kompakte Zubehör wird auf den Reflektorkopf des Blitzgerätes aufgesteckt. Durch indirektes Blitzen ergibt sich eine harmonische und weiche Ausleuchtung. Der Reflexschirm läßt sich einfach zusammenfalten und findet daher auf kleinstem Raum Platz. ZUBEHÖR • Beim indirekten Blitzen wird der Blitzbereich nicht mehr angezeigt und die HSS-Funktion deaktiviert.
HINWEISE ZUR BENUTZUNG Während des Fotografierens • Das Blitzgerät erzeugt sehr helles, gleißendes Licht. Achten Sie bitte darauf, es nicht in unmittelbarer Nähe Ihrer Augen zu zünden. Batteriehinweise • Entnehmen Sie bitte die Batterien, falls das Blitzgerät längere Zeit nicht genutzt wird. Damit vermeiden Sie eine Beschädigung des Batteriefachs durch auslaufende Batterien. • Die Eigenschaften von Alkali-Mangan Batterien sind abhängig von der Außentemperatur, der Lagerung usw.
• Bei Temperaturen außerhalb des angegebenen Bereichs verändern sich Kontrast und Ansprechzeit der LCD-Anzeigen, so daß die Anzeigen schwer lesbar werden können. Bei sehr hohen Temperaturen können Datenmonitore vorübergehend dunkel werden. Nach kurzer Verweildauer unter mittleren Temperaturen verhält sich die Anzeige wieder normal. • Wird das Blitzgerät plötzlichen Temperaturänderungen ausgesetzt (z.B.
BLITZLEISTUNG Leitzahlen (für Meter und ISO 100): Einzelblitz (normaler Blitzbetrieb) LeistungsObjektivbrennweite wahl 17 24 28 35 50 1/1 18 30 32 38 44 1/2 12 21 22 26 31 1/4 9 15 16 19 22 1/8 6,4 10 11 13 15 1/16 4,5 7,5 8 9 11 1/32 3,2 5,3 5,7 6,7 7,8 (mm) 70 50 35 25 17 12 8,8 85 56 38 27 19 13 9,7 Drahtlose TTL-Blitzfernsteuerung (Leitzahlen für Meter und ISO 100) LeistungsObjektivbrennweite (mm) wahl 17 24 28 35 50 70 85 1/1 14 25 26 30 35 41 42 High-Speed-Synchronisation Objektivbrennweite Versch
Ausleuchtwinkel Objektivbrennweite (mm) Ausleuchtwinkel 17 24 28 35 50 70 85 Vertikal 115° 60° 53° 45° 34° 26° 23° Horizontal 125° 78° 70° 60° 46° 36° 31° Abmessungen (BxHxT) 77,5 x 132 x 95,5 mm Gewicht 370g (ohne Batterien) Die technischen Daten entsprechen dem aktuellen Stand zum Zeitpunkt der Drucklegung. Änderungen vorbehalten. 77 BLITZLEISTUNG Wird automatisch abgegeben bei schwachem AFBeleuchtungsgerät Kontrast und geringem Umgebungslicht.
MEMO 78
© 2003 Konica Minolta Camera, Inc.