Service manual

CONTENTS
3 DIS./ASSEMBLY1 DIS./ASSEMBLY3 DIS./ASSEMBLY2 ADJUSTMEN3 DIS./ASSEMBLY3 SERVICE3 DIS./ASSEMBLY
4 ELECTRIC PARTS LIST
3 DIS./ASSEMBLY
5
ISW
[12] Removing and Reinstalling the Fixing
Temperature Sensors 1 and 2............... 1-O-9
[13] Removing and Reinstalling the
Thermostat (TS1)................................. 1-O-11
[14] Removing and Reinstalling the
Thermostat (TS2)................................. 1-O-12
< RADF >
EXTERNAL SECTION ...........................................1-P-1
[1] Removing the RADF...............................1-P-1
[2] Reinstalling the RADF ............................1-P-2
ORIGINAL FEED/CONVEYANCE/EXIT
SECTION ...............................................................1-P-4
[1] Replacing the Pickup Roller and
Conveyance Roller Rubber.....................1-P-4
[2] Cleaning the Cleaning Pad.....................1-P-5
[3] Replacing the Double Feed Prevention
Roller / Double Feed Prevention Roller
Rubber....................................................1-P-5
< LCT >
PAPER FEED SECTION ...................................... 1-Q-1
[1] Cleaning the Paper Dust Removing
Brush ..................................................... 1-Q-1
[2] Cleaning the LT feed PS (PS106)/
LT first paper feed PS(PS107)............... 1-Q-1
[3] Removing and Reinstalling the
Paper Feed Roller Unit .......................... 1-Q-2
[4] Replacing the Paper Feed Roller Rubber/
Feed Roller Rubber ............................... 1-Q-2
[5] Replacing the Double Feed
Prevention Roller Rubber ...................... 1-Q-3
[6] Replacing the LT feed MC (MC101)/
LT first paper feed MC (MC102)............ 1-Q-5
[7] Replacing the C-403 Up/Down Wires.... 1-Q-6
[8] Replacing the C-404 Up/Down Wires .. 1-Q-10
< FN >
EXTERNAL SECTION .......................................... 1-R-1
[1] Removing and Reinstalling the Booklet
Tray (FN-6 only)..................................... 1-R-1
[2] Removing and Reinstalling the Top
Cover/1 .................................................. 1-R-1
[3] Removing and Reinstalling the Top
Cover/2 .................................................. 1-R-2
[4] Removing and Reinstalling the Side
Cover ..................................................... 1-R-2
[5] Removing and Reinstalling the Front
Door....................................................... 1-R-3
[6] Removing and Reinstalling the Rear
Cover ..................................................... 1-R-3
[7] Removing and Reinstalling the Main
Tray ....................................................... 1-R-4
[8] Removing and Reinstalling the Main
Paper Exit Opening Cover..................... 1-R-5
[9] Removing and Reinstalling the Booklet
Paper Exit Opening Cover......................1-R-5
CONVEYANCE SECTION.....................................1-R-6
[1] Replacing the Paper Exit Roller
(Sponge Roller) ......................................1-R-6
[2] Replacing the Intermediate Conveyance
Roller (Sponge Roller)...........................1-R-7
[3] Removing and Reinstalling the Paper
Exit Opening Unit ...................................1-R-8
MAIN TRAY SECTION ..........................................1-R-9
[1] Replacing the Tray Up/down Motor
(M703) ....................................................1-R-9
[2] Replacing the Up/Down Wire .................1-R-9
STACKER SECTION...........................................1-R-13
[1] Removing and Reinstalling the Stacker
Unit Cover ............................................1-R-13
[2] Removing and Reinstalling the Stacker
Unit .......................................................1-R-13
STAPLER SECTION ...........................................1-R-15
[1] Removing and Reinstalling the Stapler
Unit Cover ...........................................1-R-15
[2] Removing and Reinstalling the
Clincher ................................................1-R-16
[3] Removing and Reinstalling the
Stapler..................................................1-R-17
< PI >
EXTERNAL SECTION........................................... 1-S-1
[1] Detaching / Re-installing
the External covers.................................1-S-1
PAPER FEED UNIT...............................................1-S-2
[1] Replacing the Paper feed roller and
Feed roller ..............................................1-S-2
[2] Replacing the Double feed prevention
roller and Torque limiter .........................1-S-3
< PK >
PUNCH SECTION................................................. 1-T-1
[1] Replacing the Punch unit ....................... 1-T-1
[2] Cleaning the Punch Edges and Punch
Scraps Full PS (PS802) ......................... 1-T-2