Repair Manual
Table Of Contents
- REPAIR GUIDE
- ■Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the TEBURE ASSY, SHUTTER ASSY
- 3. Disassembly of the MIRROR BOX ASSY, BATTERY HOLDER
- 4. Disassembly of the IMAGE BOARD ASSY, MAIN BOARD ASSY
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the TOP COVER ASSY
- 9. Disassembly of the BACK COVER ASSY
- 10. Disassembly of the CCD ASSY, DC JACK HOLDER
- 11. Disassembly of the CARD COVER HOLDER, SIDE COVER, FRONT COVER ASSY
- ■How to replace "SHUTTER ASSY"
- ■Required adjustment, setting and confirmation items after repairing (exchanging parts)
- ■Related adjustment and required setting items
- ■Using HIT System
- ■Adjustment/Check items available with 2181 ROM Pack
- ■Viewfinder Back Adjustment
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Manual Set SS Adjustment
- ■SPC Position Adjustment
- ■Aperture Preset Check
- ■PI-PR Adjustment
- ■Preparation before AF adjustment
- ①AF Area Adjustment
- ②Pitch Yaw Adjustment
- ③EZ Check
- ④EZ Adjustment
- ■Assist MODE
- ■LCD Displays Check
- ■Preparing the 2181 adjustment program
- ■Starting up the 2181 adjustment program (in the adjustment mode).
- ■Back up Flash ROM data of Master Body
- ■Adjustment of CCD Vsub voltage
- ■Setting of Master body and chart for the adjustment of CCD position
- ■Adjustment of CCD position and perspective
- ■Adjustment of the frequency for camera shaking (ACT DRV FREQ)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of the AE (AE)
- ■Sensitivity adjustment (GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■Setting of Destination (DESTINATION)
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
(2181) 9
REPAIR GUIDE
+
−−
−−
−
■■
■■
■
Fig. 4Fig. 4
Fig. 4Fig. 4
Fig. 4
SHUTTER CHARGE GEARSHUTTER CHARGE GEAR
SHUTTER CHARGE GEARSHUTTER CHARGE GEAR
SHUTTER CHARGE GEAR
SHUTTER SPACERSHUTTER SPACER
SHUTTER SPACERSHUTTER SPACER
SHUTTER SPACER
■■
■■
■
Fig. 5 SHUTTER ASSY InstallationFig. 5 SHUTTER ASSY Installation
Fig. 5 SHUTTER ASSY InstallationFig. 5 SHUTTER ASSY Installation
Fig. 5 SHUTTER ASSY Installation
1. Supply power to the charg motor at 2V/1A to drive it normally until the mirror raises1. Supply power to the charg motor at 2V/1A to drive it normally until the mirror raises
1. Supply power to the charg motor at 2V/1A to drive it normally until the mirror raises1. Supply power to the charg motor at 2V/1A to drive it normally until the mirror raises
1. Supply power to the charg motor at 2V/1A to drive it normally until the mirror raises
completely.completely.
completely.completely.
completely.
DC Power SupplyDC Power Supply
DC Power SupplyDC Power Supply
DC Power Supply
(2V/1A)(2V/1A)
(2V/1A)(2V/1A)
(2V/1A)
DriverDriver
DriverDriver
Driver
2. Insert screw driver into the hole of "SHUTTER CHARGE GEAR", and put "SHUTTER2. Insert screw driver into the hole of "SHUTTER CHARGE GEAR", and put "SHUTTER
2. Insert screw driver into the hole of "SHUTTER CHARGE GEAR", and put "SHUTTER2. Insert screw driver into the hole of "SHUTTER CHARGE GEAR", and put "SHUTTER
2. Insert screw driver into the hole of "SHUTTER CHARGE GEAR", and put "SHUTTER
ASSY" by holding the screw driver at the 90 degrees position shown on the picture.ASSY" by holding the screw driver at the 90 degrees position shown on the picture.
ASSY" by holding the screw driver at the 90 degrees position shown on the picture.ASSY" by holding the screw driver at the 90 degrees position shown on the picture.
ASSY" by holding the screw driver at the 90 degrees position shown on the picture.