Instructions / Assembly

ManualsBrandsMinoura ManualsBike Parts & AccessoriesKagura SmartTurbo Conversion Unit for Minoura Trainers

indoor bicycle trainer resistance unit – instruction manual

(ver.1.1 2017/8)

This is an upgrading unit to change your Minoura trainer to the latest SMART trainer that allows you to enjoy the

virtual courses and competitions on the internet.

Please be sure this is just a resistance unit. Refer your own trainer's instruction manual how to mount and use the

bike correctly.

• The supplied resistance unit needs to be attached to the frame before use.

The unit is very heavy and special care must be taken not to drop the unit. Be especially careful of the

ywheels (one at each end. One chrome, one black) dropping or otherwise hindering the unit will affect the

balance of the unit and void any warranty. Each unit is carefully and fully checked and in full working order

prior to being packaged.

• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.

Tire and roller contact will eventually wear both your tire and the trainer roller.

Wipe the tire surface to remove any solid dust away before setting the bike on the trainer in order to maximize

both the tire and the drive roller life. Minoura recommends adding 10% more air to your tire when training.

• Avoid using your brakes to stop your workout. Let the ywheel come to a stop naturally. Using your brakes

will cause damage to the unit and your tire, possibly causing it to burst.

• Be careful not to pinch your nger when raising up or folding down the resistance unit, or folding the frame.

• Touching the spinning wheel and/or any other moving parts while training may cause serious injury.

Keep children, pets, towel and clothings away from the trainer when in use.

• This product requires electric power souce AC 100 – 240V. Do NOT apply any moisture or mud to the electric

magnet unit. Keep clean and avoid any dust even when using indoors.

If your electric plug shape is different from the supplied one, please use appropriate plug adapter.

• LST9200 has two different resistance systems; the electric magnet and the physical neodymium magnet.

When using the electric magnet as a smart trainer, adjusting the resistance level can be done only by the

Contact

- 1 -

If you need support, please first contact the shop you purchased this product from or contact

the distributor in your country for assistance. A list of our distributors can be found here:

http://www.minoura.jp/english/support/shop/distributor.html.

If you need further support, contact us at one of the places listed below.

MINOURA North American Tech Center MINOURA Japan Headquraters

(for U.S. residents ONLY)

(for ALL customers)

Hayward, California, U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan

Phone: 1-510-538-8599 (8 am - 5 pm, Mon - Fri, PST) Fax: +81-584-27-7505

Fax: 1-510-538-5899 Email: minoura@minoura.jp

Email: support@minourausa.com Web: www.minoura.jp

Made in Japan

Important Notes

Please read carefully before use

Summary of content (5 pages)

PAGE 1
indoor bicycle trainer resistance unit – instruction manual (ver.1.1 2017/8) This is an upgrading unit to change your Minoura trainer to the latest SMART trainer that allows you to enjoy the virtual courses and competitions on the internet. Please be sure this is just a resistance unit. Refer your own trainer's instruction manual how to mount and use the bike correctly.
PAGE 2
wireless control via smart phone or PC. No manual control allowed. Smart phone, tablet, WindowsPC or Macintosh must be set up separately. Control applications are not included and are available from third party companies specializing in software applications for SMART trainers. Neodymium magnet system (non electric) allows LST9200 to be used without electricity and provides basic resistance for warming up or cooling down. • LST9200 regularly outputs radio signals.
PAGE 3
How To Replace Your Mag Unit Case-1 : There is a rubber pad between the Mag unit and the base plate ① Remove the existing Mag unit. ② Replace the mounting bolts to the supplied longer one, and install LST9200 unit. Rubber Pad (Fig. C) (Fig. B) 23.5mm 19.5mm Case-2 : Mag unit is installed on the base plate directly ① Remove the existing Mag unit. ② Continue using the same bolts to mount LST9200 unit. (Fig. E) (Fig.
PAGE 4
Connecting Power Cable & Check 1 ! Insert the round side plug into the connecting port behind the Electric Magnet Unit. (Fig. G) Do NOT force to push the plug too much. The port could be damaged seriously. 2 Insert the power cable (not shown in the picture) to the AC Adapter firmly, then connect to the outlet. 3 Power turns on automatically. The Red LED will turn on, and the Blue LED will be blinking. (Fig. H) 4 To turn off the power, simply remove the power cable from the outlet.
PAGE 5
How To Use Neodymium Magnet The red lever is for sliding the neodymium magnet to generate resistance between the magnet and the steel flywheel. It does not require any electric power so it allows to use outdoors as same as the stationary trainer. 4 levels are available. Good for light training sessions, warming up or cooling down, or daily excercise. To use it, slide the magnet unit while pushing down the red lever. Set the lever in the fixed position.