User Guide

ManualsBrandsMinoura ManualsOtherMAG-500

- 1 -

Resolution Diagram

MAG-500 series instructions manualMAG-500 series instructions manual

MAG-500 series instructions manual

F-1 : Coupling (Right) LM-1 : Flywheel Cover (white)

F-4 : Coupling Cover (move side) LM-2 : Flywheel Side Inner Case

F-7 : Hub Handle (3/8” thread) LM-3 : Mag Side Inner Case

F-9 : Skewer Nut Protector (Grommet) LM-4 : Dial Outer Cover

HF-4 : Rubber Frame Cap (35mm) LM-5 : Remote Outer Cover

M5-1: MAG-500 Main Frame LM-6 : Flywheel (500g)

M5-2: Rubber Foot Cap (28.6mm) LM-7 : Alloy Rotor

M5-3: Pressure Plate LM-8 : Axle w/ Bearings

MF-3 : Mirco Adjust Knob Set LM-9 : Connection Plate

LM-10 : Base Plate

F-1

F-4

F-7

M5-2

HF-4

M5-1

MF-3

LM-1

LM-6

LM-2

LM-9

LM-8

LM-10

LM-3

LM-7

LM-4 / LM-5

F-9

M5-3

Summary of content (4 pages)

PAGE 1
MAG-500 series instructions manual Resolution Diagram F-4 F-1 F-9 M5-1 F-7 LM-1 LM-6 MF-3 M5-2 M5-3 LM-8 LM-3 HF-4 LM-2 LM-9 LM-7 LM-10 LM-4 / LM-5 F-1 : F-4 : F-7 : F-9 : HF-4 : M5-1 : M5-2 : M5-3 : MF-3 : Coupling (Right) Coupling Cover (move side) Hub Handle (3/8” thread) Skewer Nut Protector (Grommet) Rubber Frame Cap (35mm) MAG-500 Main Frame Rubber Foot Cap (28.
PAGE 2
IMPORTANT NOTES • Read all instructions including the back page of the POP card board carefully before use. • Some assembly required. • Keep the manual handy at all times. • Do NOT use trainer for any other purpose than instructed. • The trainer is manufactured to precise standards. You may not disassemble or rebuild it. • "Magturbo" is the trademarks of Minoura Co.,Ltd. and may not be copied. WARNINGS ! Use two-wheeled bicycles only. Tandems may be used if balanced correctly.
PAGE 3
How To Setup Your MAG-500 Trainer 1 Open the frame support legs and fit the rubber feet at the correct angle so the base is in full contact with the floor. Do NOT remove the round metal plates from inside the rubber feet when fitting. NOTE: If the both legs don’t touch the floor at same time and if one side of the leg is still being lifted up slightly, pull up the leg upward strongly then place the trainer on the floor again. 2 Open both couplings by turning the right side hub handle (see Fig.
PAGE 4
! You must not be riding the trainer when you are adjusting the white lever on the Mag unit for load force. Make sure all parts have stopped spinning. Do not try to adjust the lever with your feet while riding. HOW TO INSTALL THE REMOTE LEVER (Fig. G) You can install the remote lever on anywhere the diameter is between 22.2mm (7/8”) and 31.8mm (1-1/4”) like as on the handlebar. 1 Fully loosen the knob bolt on the plastic holder until it stops then push down the bolt to open the holder. (see Fig.