105mm+-2 105mm+-2 Getting Ready Under Still Image Shooting Mode Basic Photography For Still Image Set The Shooting Mode (Default: AUTO) 1. Press the Power Button to turn on the camera. 2. Make sure the camera is set at Still Image Shooting Mode. 3. Use Tele/Wide Button to zoom in and zoom out. 4. Press the Macro Button ( ) if required (closer than 60cm). 5. Press the Shutter Button halfway for focusing and then press the Shutter Button fully down to capture the image.
105mm+-2 Under Still Image Shooting Mode PROGRAM MODE 105mm+-2 Under Still Image Shooting Mode SUNSET MODE Operation St eps Operation St eps 1. OK / MENU 2. or 3. OK / MENU MODESET AUTO PROGRAM NIGHT PORTRAIT SUNSET EXIT : MENU In program mode, the metering, sharpness, effect, WB, frame, shooting flash & ISO can be adjusted. MOVE: 1. OK / MENU 2. or 3. OK / MENU MODESET AUTO PROGRAM NIGHT PORTRAIT SUNSET EXIT : MENU Under this mode the settings below will be locked.
105mm+-2 Under Still Image Shooting Mode 105mm+-2 Under Still Image Shooting Mode Other Settings Zoom In & Zoom Out Manual Focus The Zoom Indication Bar, appearing on the top side of the TFT LCD Monitor shows the current zoom status. This camera allows maximum 3.0x optical zoom and 5.0x digital zoom. MENU OK 999 7M 2m ( 2m ) The focus is set at 2M. ( ) The focus is set at infinity. ( 0.8m ) The focus is set at 0.8m.
105mm+-2 105mm+-2 Under Still Image Shooting Mode Self-timer Under Still Image Shooting Mode Voice Memo With the 10 sec. Self-timer ( ): The image wi ll be taken after an inter val of 10 seconds once the Sh utter Button is released. MENU OK MENU OK There are 2 ways to add the voice memo to an image: MENU OK MENU OK With the 2 sec. Self-timer ( ): The image wi ll be taken after an interval of 2 seconds once the Sh utter Button is released. 2S 999 7M X1.
5mm+-2 Under Still Image Shooting Mode Image Quality ( Default:FINE) The Image quality options are provided as follows: QUALITY S. FINE FINE NORMAL EXIT : MENU 105mm+-2 Under Still Image Shooting Mode Continuous Shooting ( Default:SINGLE) 1 ( ( ( ) Super Fine ) Fine ) Normal MOVE: 1.SINGLE: No continuous shooting. 2.CONTINUOUS: You can have the continuous shooting function starting by pressing the Shutter Button and on hold and ending by letting go of the Shutter Button.
105mm+-2 Under Still Image Shooting Mode Norma l EFFECT NORMAL B&w SEPIA NEGATIVE EXIT : MENU B& W SEPIA MOVE: NEGATIVE Under Still Image Shooting Mode OSD Information(Default:DETAIL) Effect( Default:NORMAL) NOR 105mm+-2 NOR No special effect is added to the picture. Turn the image into black and wh ite. Turn the image into yellowish brown. Turn the image into negative film effect . OSD INFORMATION OFF BASIC DETAIL GRID 3X3 GRID 6X4 EXIT : MENU Operation St eps Operation St eps 1.
105mm+-2 105mm+-2 Under Still Image Shooting Mode ISO Value ( Default:AUTO) Under Still Image Shooting Mode RGB 999 7M 999 7M MENU OK MENU OK MENU OK Operation St eps 1. 2. 3. Operation St eps 1. 2. 3. AUTO 100 200 400 800 1000 or or To adjust the ISO value, you will need to set the working mode at Program Mode ( ) and press the Delete Button ( ) first. Press Up or Down Button to the ISO setting and choose the ISO value you prefer and press the OK/Menu Button to confirm.
105mm+-2 Under Playback Mode ( 105mm+-2 ) Under Playback Mode ( ) Playback Of Still Image, Movie Clip And Audio Clip Please press Playback Button ( ) and the camera will show the stored still images, movie clips and audio clips (voice recording). Use the Right and Left Button to choose the file you would like to play. 1. Still Image Still images are the images with no special signs such like ( ) and ( ). ( ) represents that the images are with voice memos. MENU OK Operation St eps 1. 2. 3.
105mm+-2 Under Playback Mode ( 105mm+-2 ) Trim A Still Image Under Playback Mode ( ) Set An Image With Protection 100-0021 PROCCESSING! 8:08 AM 2007/01/05 X1.9 The camera will save the trimmed image as a new image after you confirm the request. Display Image Information Set All Images With Protection 1. Press the OK/Menu Button and choose "PROTECT". 2. Choose "ALL" and press OK/Menu Button to confirm the request. ( ) will show on the TFT LCD Monitor when the protection is set. 3.
105mm+-2 Under Playback Mode ( 105mm+-2 ) Delete Image Under Playback Mode ( Copy To Card Operation St eps 1. OK / MENU 2. or 3. or DELETE SELECT ALL EXIT : MENU ) MOVE: Operation St eps 1. OK / MENU 2. or 3. or COPY TO CARD NO YES EXIT : MENU You can delete the selected image(s) or all images with this function. Please press OK/Menu Button and choose "DELETE" and following the steps below.
105mm+-2 Under Playback Mode ( 105mm+-2 ) Resize A Still Image Under Playback Mode ( Rotate An Image Operation St eps 1. OK / MENU 2. or 3. or RESIZE 2560 X 1920 2048 X 1536 1600 X 1200 1024 X 768 640 X 480 EXIT : MENU ) MOVE: Operation St eps O RIGHT90 LEFT90O O 180 HORIZONTAL VERTICAL EXIT : MENU Set A Still Image As An Option Of The Start-up Images This function allows the option of using your own image as the start-up screen. 1.Choose the image you would like to use. 2.
105mm+-2 105mm+-2 PC Connection TV Connection General Introduction How to Connect with a Computer Computer / Notebook Connection Computer When the USB/Video Cable is in connection with the computer while the camera is on, the camera will automatically go to the PC Mode from any working mode and turn off TFT LCD monitor. Turn on the TV and switch the TV/Video switch to A/V mode. In this Mode, you can download images to your computer . Power on the camera and then switch to the Playback Mode.
105mm+-2 105mm+-2 PC Connection PC Connection Installing The Camera's Driver Under Microsoft Windows 98SE 1 2 If the auto run program fails under certain situation, please go to the Start Menu, click "Run" and key in "CD-ROM Drive:\ AutoRun.exe" and then click "OK" Button. 3 Under Microsoft Windows 2000 5 1 2 3 52 53 150mm+-2 If the computer h as been installed with \ Direct X 8.
105mm+-2 105mm+-2 PC Connection PC Connection I nstalling Ulead Photo Explorer 4 Under Windows Operating System (Windows 98SE/2000/ME/XP) 1 2 3 4 Having DirectX 8.0 or later already, the computer will skip the installation procedure from step 2 above and go to the following window directly. Please complete the driver installation with a "OK" Click. 150mm+-2 Under Microsoft Windows ME / XP The camera's driver is not required under Windows ME and Windows XP.
105mm+-2 PC Connection PC Connection 7 105mm+-2 8 8.5 8.5 13 8.5 14 8.5 8.5 8.5 8.5 9 10 8.5 8.5 Under Macintosh Operating System (Mac 9.X or later) Step 1 : Turn on the computer. 150mm+-2 8.5 Step 2 : Insert the CD into the CD-ROM Drive. The computer will create an icon named "Driver CD" on the desktop. 11 12 8.5 8.5 8.5 Step 3 : Double click on the icon and choose the language you prefer by double clicking on one of the folders below. PEX 2.0: English 8.5 PEX 2.
105mm+-2 105mm+-2 PC Connection PC Connection Step 4 : Select PEX2.0 Installer to install. Step 5 : Press Continue for the next step. Step 7 : Step 6 : A welcome screen will jump out. Please press Continue for the next step. Please read through the contract. If you agree with the contract, please press Agree. If not, please press Disagree, and installation will be cancelled simultaneously. Step 9 : Select the folder you just installed, and press Choose for the next step. PEX2.
105mm+-2 105mm+-2 PC Connection PC Connection Downloading the Image(s) Under Windows Operating System (Windows 98SE/2000/ ME/XP) Downloading Image(s) From Removable Disk Under Macintosh Operating System (Mac 9.X or later) Downloading Image(s) From Removable Disk 1. Turn on the PC. 1. Turn on the PC. 2. Switch on the camera. 2. Switch on the camera. 3. Connect the camera to the PC by USB cable under any working mode. Please make sure the USB Cable is well connected to both the PC and camera. 3.
105mm+-2 105mm+-2 Appendix Appendix Specifications Error Message Table Messages Solutions CARD FULL Delete the stored image(s) in the memory card or insert a new memory card. MEMORY FULL There is insufficient internal memory capacity for storing an image. Delete the stored image(s) in the flash memory. CARD LOCKED (ICON BLINKING) The memory card is under protection. Set the card protection switch at non-protection position. LOCK The Image can not be deleted under protection.
105mm+-2 Appendix 105mm+-2 Appendix About ArcSoft ,Inc Customer Service For the best experience with your ArcSoft software, register each of your titles right after you've completed the installation process. Contact our customer service department if you have any questions or concerns. Product FAQ (without battery and card) http://arcsoft.custhelp.com/cgi-bin/arcsoft.cfg/php/enduser/std_alp.php? Search the ArcSoft Knowledge Base to get information on how-to's, troubleshooting tips, features, and more.
105mm+-2 Appendix 105mm+-2 Appendix Things You Can Do With "ArcSoft VideoImpression" About Ulead Photo Explorer Software license You could choose : 1. Open an Existing Project . 2. Create a New Video. 3. Create a New Slide Show. The software mentioned in this manual is furnished under a License Agreement which is included with the product. This Agreement specifies the permitted and prohibited uses of the product.
105mm+-2 105mm+-2 Appendix Appendix Things You Can Do In Ulead Photo Explorer 8.5 SE Basic Browse thumbnails Ulead Photo Explorer displays files as thumbnails, allowing you to visually browse through images and media files. (picture 4) Here's an overview of what you can do in Ulead Photo Explorer. Refer to the chapters in this user guide for more details. Acquire images Acquire images from digital cameras, scanners, or memory card readers.
105mm+-2 105mm+-2 Appendix Print images in various layouts Output single-image prints, greeting cards, or print images in different photo sizes. You can also print an index sheet of thumbnails for your image collection. (picture 7) Create slideshows Assemble images, video and audio files into a multimedia slideshow. Apply cool transition effects to your slideshow.
105mm+-2 105mm+-2 150mm+-2
