Parts and Instruction Manual M2400 Electric Burnisher W/ Dust Control Option
This manual is furnished with each new MINUTEMAN M2400. This provides the necessary operating and preventive maintenance instructions. Operators must read and understand this manual before operating or servicing this machine. This machine was designed to give you excellent performance and efficiency. For best results and minimal cost, please follow the general guidelines below: · Operate the machine with reasonable care.
Parts and Instruction Manual
Table of Contents IMPORTANT SAFETY INSTRUCTIONS .............................................................................................. 1 INSPECTION ........................................................................................................................................ 2 GROUNDING INSTRUCTIONS ........................................................................................................... 2 ELECTRICAL .........................................................................
FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING WARNING - To reduce the risk of fire, electric shock, or injury: • Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. WARNING To reduce the risk of electric shock - Do not expose to rain. Store indoors.
INSPECTION Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly inspected before shipment, and any damage is the responsibility of the delivery carrier who should be notified immediately. WARNING • Read Instruction Manual before operating this piece of equipment. • To reduce the risk of fire use only commercially available floor cleaners and waxes intended for machine application. • To reduce the risk of electrical shock, do not expose to rain. Store indoors.
POUR USAGE COMMERCIAL SEULEMENT MODE D’EMPLOI SECURITAIRE Lorsque l’on utilise un appareil électrique, des précautions de base doivent toujours être suivies telles que: BIEN LIRE LE MODES D’EMPLOI AVANT USAGE AVERTISSEMENT - Pour réduire les risques de feu, choc électrique ou blessure: • Ne pas quitter l’appareil lorsque la prise de courant est branchée. Débrancher de la sortie électrique lorsque la machine n’est pas en usage ou pour en faire le service.
INSPECTION Déballer soigneusement en constatant s’il y, a lieu tout dommage apparent. Chacune des pièces d’équipement est entièrement inspectée à l’usine et tout dommage de transit est la responsabilité de la compagnie de transport qui devrait être prévenue immediatement. AVERTISSEMENT • S.V.P. lire le manuel d’instruction avant d’opérer cette pièce d’équipement.
Model 2400 Burnisher Operating Instructions Install 20 Inch Pad inside pad driver. Hand Tighten center clip or push straight in. Hand Tighten or push in. DO NOT FORCE. 1. Install the polishing pad on to the pad driver. Make sure your installing a true 20” polishing type pad. Then install the locking centering device cup by lining up the threads on the pad driver and the cup and push straight down, or just screw the cup devise onto the pad driver. Hand tighten the cup to the pad driver.
Model 2400 Burnisher Operating Instructions 4. After the machine has started the pad pressure gauge, located at the backside near the rear of the base, should be reading at the top of the white zone, or telling the operator the pad is off the floor. Now, to increase the pad pressure keep the burnisher running with one hand and pushing the machine in a back and forth motion.
Model 2400 Burnisher Operating Instructions Preventive Maintenance 1. Inspect motor carbon brushes approximately every 250 hours. A set of carbon brushes should last as long as 2500 hours. Premature wear may indicate other problems with the motor. These can be inspected by removing the motor cover. Indications for changing carbon brushes would be if the indicator light comes on or if the carbon brushes are flush with or slightly recessed in the brass brush holder. 2.
Exploded Views Base Assembly Parts and Instruction Manual Page 8
Base Assembly BOM Item 1 1A* 2 3 4 5 6 6A 7 7A 8 9 10 11 12 12A* 12B 12C* 13 13A 14 14A 15 16 17 18 19* 20 21 22 23 24 25* 26 27 28 28A 29 30 31 32* 33 34 35 36 37 38 39 40 41 42 43 44 44A V.S.) 45 46 47 48 49 50 51 51A 52 Part No. Qty.
Handle Assembly Parts and Instruction Manual Page 10
Handle Assembly BOM Item Part No. 1 1A 2 2A 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 40A 150002 740600 150003 150004 170040PLT 190006 190008 190009B 190010 190015 190016 190022 190023 190024 190029 190033B 230025 230027 710186 710380 711128 711160 711162 711214 711316 711373 711387 711400 711504 711554 711619 711620 715175 715237 715501 715950 740029 740361 740362 741129 742259 742313 832859 Parts and Instruction Manual Qty.
Dust Control Option Parts and Instruction Manual Page 12
Dust Control Option BOM Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 230034 230101 380035 390061 710197 710556 711202 711350 711505 711524 711594 711903 715100 762131PTD 762132 762396B 762403 762404 762409PLT 462410 762411 762415 762416PLT 805042 833214 Parts and Instruction Manual Qty. 1 1 1 1 2 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3.166 Ft 1 Description Dust Tube Hose 2” C/L 14” Gasket 4.31 x 5.81 x .19 O-Ring - Valve Stem SCR-SC 5/16-18 x .75 SCR-MC 10-32 x .
Wiring Diagrams Parts and Instruction Manual Page 14
Parts and Instruction Manual Page 15
Minuteman International Made Simple Commercial Limited Warranty Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in workmanship and materials under normal use. Minuteman will, at its option, repair or replace without charge, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals.