User Manual Cyclo 400/600 Series ™
Welcome Contents Thank you for purchasing this Mio. Please read this manual carefully before using your Mio for the first time. Keep this manual in a safe place and use as your first point of reference. Welcome..............................................................................................2 Knowing your device............................................................................4 Accessories.....................................................................................
Regulatory information..................................................................35 End user license agreement.........................................................35 A to B (Address, POI, Favourite, or Point on map).......................18 Workout mode....................................................................................20 Workout by Distance.....................................................................20 Workout by Time......................................................
Knowing your device ❶ ❷ ❸ ❹ ❺ ❻ ❼ ❽ **May be sold separately and used for Cyclo 405/605 HC only. For Cyclo 605 HC, the sensors will enter Sleep mode after 15 minutes of inactivity, and wake up automatically and transfer data to your device after 20 seconds of activities. Note: Depending on the specific model purchased, the colour and look of your device and accessories may not exactly match the graphics shown in this document. Note: This device is ANT+ certified. Visit www.thisisant.
Getting started CAUTION: For optimal performance of the lithium battery, note the following: • Do not charge the battery where the temperature is high (e.g. in direct sunlight). • Failure to follow the battery usage instructions could cause damage to your device, battery and even bodily injury or property damage and will void the warranty. • When storing the product for a long period of time, charge the battery to 50% – 80% capacity to prevent excess discharge.
Installing the device Enter the Startup Key (which is printed on the bottom of the box) and then tap OK to unlock your device. You will only have to do this the first time you use the device. 5. Once your device is turned on, it will search for satellite signals automatically. This may take several seconds depending on the location. Mounting the device on your bike The bike mount kit includes two types of rubber pads, allowing you to attach the bike mount to your bike securely.
3. To remove the device from the bike mount, rotate it counterclockwise. 3. When done, you can manually pair the sensor with your device by tapping Main menu > Settings > Sensors > Cadence/Speed. Installing the sensors on your bike (Cyclo 405 HC) The cadence sensor contains a replaceable CR2032 battery. Follow the instructions below to replace the battery: 1. Follow the instruction below to install the cadence/speed sensor kit on your bike. 1.
• Cadence sensor 1. Before using the heart rate monitor, wet the contacts on the back of the chest strap. Note: If possible, you can also use an electrolyte gel (usually available in local sports stores) to ensure good contact. 1 2 3 4 2. Adjust the elastic strap so it’s snug while you are putting it on. Ensure that you can take a good deep breath after putting on the strap. 3. Follow the instructions below to wrap the strap around your back, and then secure it on the other side with the buckle.
Operating basics 1. Locate the battery cover on the back of the monitor, and then twist the cover anticlockwise (e.g. by using a coin) to remove the cover and battery. 2. Insert the new battery into the battery chamber and replace the cover. Using the POWER button 3. Twist the cover clockwise (e.g. by using a coin) to close the cover. • Turning on the device Press and hold the POWER button for 3 seconds to turn on your device.
3 SEC Unlocking the screen Your device will automatically lock the screen after 30 seconds (by default) of inactivity. When the screen is locked, press the POWER button briefly to unlock the screen. Note: You can change the screen lock setting by tapping Main menu > Settings > System > Screen > Screen Lock Timer. Your device will automatically turn off after 10 minutes (by default) of inactivity. The Power Off/Cancel screen will pop up and the device will be turned off if you do not make a selection.
No. Description No. Icon Description ❸ You can set workouts by entering your goals, such as by distance, by time, or by calories. ❸ Heart rate sensor Depending on your model, the icon will display when the sensor is paired with the device. ❹ Start to plan your route by selecting the locations, such as home, address, tracks, POI, etc. ❹ Cadence sensor* ❺ Speed sensor* ❺ Based on distance or time, the device will plan 3 routes for you to choose from.
ABC keyboard Managing data on the device Numeric keypad CycloAgent CycloAgent™ is a tool for synchronising data between your CycloTM device and the MioShareTM website, and for managing and updating your Cyclo device via your computer. Note: Make sure that you have an active Internet connection for this feature. Please make sure of the stable Internet connection and bandwidth for the possible large file of the map update. Visit the MioShare website (http://www.mioshare.com/help) to download CycloAgent.
Viewing Dashboard screens During recording, you can stop/pause it by pressing the button and then selecting the Stop/Pause option when prompted; otherwise, select Cancel to continue recording. Note: The screenshots and other presentations shown in the following sections may differ from the actual screens and presentations generated by the actual product. • The Dashboard provides the extended screens that can be used to assist you in your travels and trainings.
Starting navigation Using the Navigate wizard Your device is equipped with maps that provide street-level detail for navigation, including POIs (Point of Interest) such as bike stores, restaurants, points of emergency, and more. The Navigate wizard allows you to search the location easily. Tap GO to start navigating. • Tap and then tap Yes when prompted. The location has been added to Favourite. • Tap • / to zoom in/out the elevation plot.
Finding the location by Address select: a. country b. city/postal code c. street d. house number Tracks Tracks are the recorded routes that give the best experience for cycling provided by other users and official institutes. If there is no track downloaded, you can download tracks from MioShareTM at: http:// mioshare.com 1. Tap Tracks on the Navigate screen and then you can navigate and choose from individual tracks downloaded to your device. 2.
Searching for a location from the map screen 6. Disconnect your Mio from the computer and restart your Mio. 7. On your Mio, select Settings > Manage > Strava Live Segments. You can set the destination simply by pointing to it on the map screen. The segments are activated/enabled by default. • To activate a greyed out segment, tap the desired segment and tap Segment Enabled.
Searching for a location using GPS coordinates Stopping navigation To stop navigation for your ride, tap You can manually enter the coordinates of your target destination. Tap Coordinate on the Navigate screen. Tap the Latitude and Longitude fields to enter the coordinates of the location. Note: Tap the Coordinate Format option to change the input method for the latitude/ longitude coordinate. Note: Tap to change between North and South; tap to change between East and West.
Surprise Me Loop The device will generate the routes from your current location and the start/end point will be the same as your current location. The device features the Surprise Me™ function that will offer you up to three exciting routes around your location. If you’ve already taken a route from the same location, the device will try to propose you different routes, based on the possible and available roads around your current location. This way you will always be offered different routes to choose.
Favourite POI Point on map 19
Workout mode Cycling is a good aerobic fitness exercise that helps you to burn your calories, lose weight and increase your overall fitness. Workout mode of the device allows you to set workouts by entering your goals (Distance, Time, Calories) or conditions (HR Zone, Power Zone). • In the Distance field, set the desired distance to go. • In the Speed field, set the estimated average speed of your trip to calculate the estimated time of it. • Enable or disable Surprise Me.
• In the Speed field, set the estimated average speed of your trip to calculate the estimated distance of it. • Enable or disable Surprise Me. Note: For more information about Surprise Me, see the “Surprise Me" section. 3. Tap GO to start your workout. To stop, tap Stop from the Workout screen. Workout by Calories Workout by Calories allows you to set the amount of calories you want to burn during the workout. from the Main menu screen and then select the Calories 1. Tap option. 2.
• • In the Zone field, select the proper power range for the workout. The default setting is Zone 2 (166 - 225 W). Select Time mode ( ) or Distance mode ( will be generated according to your selection. 2. When done, tap ). The route • Enable or disable Surprise Me. Note: For more information about Surprise Me, see the “Surprise Me" section. 3. Tap GO to start your workout. To stop, tap Stop from the Workout screen. Indoor training mode Indoor training mode is available for selected models only.
Using the lap feature Viewing the History Note: The lap feature does not function when you are using the Indoor profile. Your device will automatically save the history as the timer starts. Information in History includes date, time, distance, average speed, altitude, and more. The lap feature functions when recording is in progress. This feature helps you review the performances of your activities.
Using WIFI Note: This feature is not available on all models. You can synchronise data (e.g. upload recordings and download saved tracks) with MioShare by accessing the Internet through WIFI (wireless local area network). WIFI allows your device to connect to the Internet through a wireless connection. To use WIFI on your device, you need access to a wireless access point. 1. Enable the WIFI function from Main menu > Settings > WIFI Sync. Note: The WIFI function of the device is disabled by default.
Pairing with your smartphone 6. The next time when you enable WIFI function, it will connect to a previously accessed network automatically. You will not be prompted to enter the password (if needed) again unless you (i) tap on the network and then tap Forget this Network; or (ii) reset the device to its factory default settings. Note: This feature is not available on all models. Depending on your model, your Mio can be connected with iPhone or Android phones.
Customising your device XYZ Note: Depending on your Mio model, certain setting options may not be available. There are various customisation options available to enhance your navigation and cycling experience. With the Settings menu, you will be able to customise your device such as the system settings, sensor settings, user profiles, map settings, and more.
Profiles Options The Profile entry screen displays the existing profile(s). Cobblestone You can set up to 6 profiles on the device. • Tap Create new profile and enter the personal data (including Name, Birth date, Weight, Gender, and profile Type) to create a new profile entry. Note: You can select the profile Type as City bike, Mountain bike, Race bike, Run & Walk or Indoor. The system will create different routes depending on the profile type.
Phone Tap the Phone option to turn on and off the Bluetooth function of the device. For more information, see the "Pairing with your smartphone" section. Note: For selected models only. Sensors Where Am I By default, the Cyclo device will automatically detect the sensors and enable the available sensor options. The Where AM I screen displays your current GPS position with the cooridnates info in map view.
Manage Lap This setting allows you to manage the recorded data on the device, including: History, Tracks, Strava Live Segments, Favourites, Addresses, and POI. • Manually only: Mark a lap when pressing the LAP ( ) button on the device. To manage the data: • And by distance: The system marks a lap automatically at the specified distance. • And by position(s): The system marks a lap automatically at one of the following starting points: 1. Tap the corresponding button in the Manage screen. 2.
Define Zones 2. Define the heart rate range in Zone 1 – 6 fields according to your personal training purpose. Otherwise, you can just keep the default settings: This setting option is for selected models only. • Heart Rate Zones: Use Heart Rate Zones to target a specific heart rate and help you reach your training goals. 1. In the Define Zones field, select By Age (BPM or %) or Custom (BPM or %).
Alerts Units • On tap screen: Enable or disable the feedback sound while tapping on the screen. The Units screen lets you select Metric or Imperial according with your preferences. • Instructions: Enable or disable the sound while getting instructions. • Di2 Alerts: Enable or disable the alert sound by the Di2 sensor during your workout. • HR Zone Alerts: Enable or disable the alert sound by HR Zone during your workout.
For more information Product Info The Product Info screen provides the general information of the device, including software and ROM versions, the End User License Agreement, and copyright information. • • Online support For 24/7 help and support with Mio products, visit our Technical Support website at: www.mio.com You can reset the device to the factory default settings by tapping Back to factory. When you select the function, all of the recorded data on the device will be cleared.
• Do not expose your Mio to extreme heat or direct sunlight for prolonged periods. Overheating may damage your Mio. Resetting the device Occasionally, you may need to perform a hardware reset when your Mio stops responding; or appears to be “frozen” or “locked-up.” Press and hold the POWER button and START/STOP button at the same time. Problem Solution Cannot establish a connection with a computer. Make sure that your Mio and your computer are both turned on before trying to establish a connection.
• • Mio products are designed to be used as an aid to safer driving. Mio does not condone speeding or any other failure to comply with your local traffic laws. It is your responsibility to drive within the posted speed limit at all times and to drive in a careful manner. Mio accepts NO liability whatsoever for you receiving any speeding fines or points on your license through using this device. Mio does not guarantee the accuracy of the data contained within this database either expressed or implied.
Regulatory information WEEE For regulatory identification purposes, Mio Cyclo 400/600 is assigned a model number of N563. Marking labels located on the exterior of your device indicate the regulations that your model complies with. Please check the marking labels on your device and refer to the corresponding statements in this section. Some notices apply to specific models only.
including but not limited to special, indirect, or consequential damages or loss of use, revenue, or profits in connection with or arising out of this Agreement or any breach of this Agreement by Mio, its suppliers or licensors or the existence, furnishing, functioning, or any use of the Software.
copies and merged portions in any form. This Agreement may be terminated immediately by Mio for any reason, including but not limited to any failure to comply with any term or condition of this Agreement. In such event, you must destroy the Product, the Software and the Documentation together with all copies and merged portions in any form. In addition, this Agreement shall terminate immediately upon the termination of the agreement between Mio and any third-party from whom Mio licenses Software.