User's Manual Part 2

ManualsBrandsMipro Electronics ManualsMixersWireless Mixer

c) d)

SCAN

SENSITIVITY

NOISE

RFCHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

SCAN

SENSITIVITY

NOISE

CHANNEL

ACT

VOLUME

c) d)

-5-

1.Whentochangechannels:

(a)Inordertoavoidexitingchannelinterference",donotchangechannelswhile

multiplechannelsareinuse.

(b)A"_"symbolonthedisplayindicatesthatitisablankfrequency.Thismeansthe

channelisunavailablebecauseofinterference.Proceeduntilanothernumeric

valueappears.

2.Whennottochangechannels:

(a)Thecurrentchannelisbeinginterferedwithorthereisachannelmalfunction.

(B)Toavoidinterferencewhenusingmultiplechannels.

(a)ThissystemincorporatesanadvancedPLL-synthesizedoscillatordesignwhichis

preprogrammedwith16switchablefrequencies.Theusermayfreelyselectany

ofthepreprogrammedfrequencies.

1.Functions:

B. SWITCHABLECHANNELFUNCTIONS

2.HowToSelectaFrequency:

(a)AutoScanningFrequencySetup:HolddowntheSCANbutton(A5)and

releasewhenthechannelindicator(A6)startstoflash.Itwillflashforatotal

of6times.ToactivatetheAutoScanfunction,presstheSCANbuttononce

whilethechannelindicatorisflashing.Anopenfrequencywillautomaticallybe

scannedandsaved/locked.*Note:TheAutoScanfunctionworksonlywhile

thechannelindicatorisflashing(6times).

Whendoneitwillautosaved/locked.

LEDdisplayflashes.

Pressandhold"SCAN"button

for1second.

Press"SCAN"buttonagainandrelease

willautoscanforanopenfrequency.

(b)ManualFrequencySetup:HolddowntheSCANbutton(A5)andrelease

whenthechannelindicator(A6)startstoflash.Itwillflashforatotalof6

times.Whilethechannelindicatorisflashing,pressandholdtheSCAN

buttonuntilthedesiredfrequencyisdisplayed(theywillincrementin

ascendingorder).Releasethebuttontoautomaticallysave/lockthefrequency.

Press"SCAN"buttonandhold,

frequencywillchangeeverytwoflashes.

Whendoneitwillautosaved/locked.

LEDdisplayflashes.

Pressandhold"SCAN"button

for1second.

OperatingManual

WIRELESSMIXER

Notes:

Summary of content (4 pages)

PAGE 1
WIRELESS MIXER Operating Manual B. SWITCHABLE CHANNEL FUNCTIONS 1. Functions: (a) This system incorporates an advanced PLL-synthesized oscillator design which is preprogrammed with 16 switchable frequencies. The user may freely select any of the preprogrammed frequencies. 2. How To Select a Frequency: (a) Auto Scanning Frequency Setup: Hold down the SCAN button (A5) and release when the channel indicator (A6) starts to flash. It will flash for a total of 6 times.
PAGE 2
WIRELESS MIXER Operating Manual C. ACT Button 1. Hold the transmitter to be programmed about 20 cm from the ACT button with the "ACT" marking of the transmitter facing the ACT button. 2. Press the ACT button. The transmitter is programmed when the RF meter shows a full signal. ACT D. Receiver Module Installation 1. Up to 2 receiver modules can be installed. 2. Each receiver module is equipped with "PILOTONE" and "NOISE LOCK" dual-squelch circuitry that eliminates noise interference. 3.
PAGE 3
WIRELESS MIXER Operating Manual E、 Control Panel Functions: E1 E2 E3 E7 E4 E5 E6 E8 E9 (E1) Headphone Jack: Stereo headphone jack to monitor the mixer output. (E2) Headphone Volume Control: Separately controls the headphone volume. (E3) Master Volume Control: Controls the overall output volume of mixer. (E4) LINE IN Volume Control: Separately controls the LINE IN (E7) volume. (E5) MIC Volume Control: Separately controls the wired microphone (E9) volume.
PAGE 4
WIRELESS MIXER Operating Manual 2. CD Player installation： A. Remove screws holding the blank panel and remove the panel (see Fig. 3-1) B. Insert the CD player into the mixer (see Fig. 3-2) C. Reinstall screws to secure the player (see Fig. 3-3) Fig. 3-1 Fig. 3-2 Fig.