WIRELESS MIXER Operating Manual 2. CD Player installation: A. Remove screws holding the blank panel and remove the panel (see Fig. 3-1) B. Insert the CD player into the mixer (see Fig. 3-2) C. Reinstall screws to secure the player (see Fig. 3-3) Fig. 3-1 Fig. 3-2 Fig.
WIRELESS MIXER Operating Manual 3. Operation Notes and Precautions: 1. Microphones have priority over music inputs. When music is playing and a microphone receives an audio signal, the music will be muted. As soon as there is no longer an audio signal to the microphone, the music will fade in. 2. Although the same frequency band may be used, it is important that the frequency of the MT-90 transmitter and the MRM-70 receiver module are not the same. Otherwise, the MA-909 will not operate properly. 3.
HANDHELD WIRELESS MICROPHONE Operating Manual 1. PART NAMES AND FUNCTIONS 1 2 3 4 5 6 7 8 (Fig.1) 1. Grill: Protects cartridge, prevents "POP" noise and prevents microphone from rolling with polygonal shape. 2. Battery Status Indicator: Indicates power on / off and the battery status. When the power switch is turned ON, the red LED indicator flashes briefly, indicating normal battery status.
HANDHELD WIRELESS MICROPHONE Operating Manual 2. BATTERY INSTALLATION (Fig.2) 1. Unscrew the battery cap (6) in a counter-clockwise direction. 2. Insert a 9-volt battery into the battery compartment (5), observing the correct polarity as shown in Fig. 2. The moment the battery touches the terminals, the indicator (2) will flash briefly, indicating correct polarity. However, if no flash occurs, either the polarity is incorrect or the battery is dead.
BODYPACK TRANSMITTER Operating Manual 1. PART NAMES AND FUNCTIONS 1 2 3 4 5 6 7 10 8 9 ACT (Fig. 1) 1. MIC Input Jack: Connects to either a lavaliere or headset microphone. (See Section 3 for connection details) 2. Power Switch: Switch to ON position for operation. Switch to OFF position when not in use. 3. Battery Status Indicator (red): Indicates power on / off and battery status. (a) When power switch is turned on: The LED indicator flashes briefly, indicating normal battery status.
BODYPACK TRANSMITTER Operating Manual 9. Battery Compartment and Cover: Accommodates one 9-Volt battery. 10.Detachable Belt Clip: Allows 360 degree rotation to suit transmitting angles. To detach simply use a screwdriver at a 45 degree angle (see diagram). 2. OPERATING INSTRUCTIONS 1. To adjust GT/MT Switch (8), and Gain Control (7), simply push down both snap locks on the sides of battery cover and flip it backwards to expose the adjustment panel. 2.
BODYPACK TRANSMITTER Operating Manual 3. AF 4-PIN INPUT CONNECTION METHOD (1) 2-Wire Electret Condenser Microphone Capsule PIN 1 SHIELD AUDIO 2 4 1 3 2 3 4 (2) 3-Wire Electret Condenser Microphone Capsule SHIELD PIN 1 2 AUDIO 4 1 3 BIAS 3 2 4 (3) Dynamic Microphone 2 1 SHIELD 3 PIN 1 2 AUDIO 4 1 3 2 3 4 (4) Electric Guitar SHIELD PIN 1 2 AUDIO 4 1 3 2 3 4 (5) Line-in (Impedance 8K ATT.
BODYPACK TRANSMITTER Operating Manual 4. BATTERY INSTALLATION 1. Push down both snap-locks on the sides of battery cover to open (Fig. 3). 2. Insert a 9-volt battery into the battery compartment observing the correct polarity as shown in (Fig. 4). Then close the battery compartment as shown in Fig. 4). (Fig.3) (Fig.4) Note: When the microphone is not in use: Make sure the power to the microphone is switched off.
BODYPACK TRANSMITTER Operating Manual Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANTNOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device.
Electronics Co., Ltd. Head office: 814, Pei-Kang Road, Chiayi, 600, Taiwan. Taipei office: 5, Lane 118, Sung-teh Road, Taipei, 110, Taiwan. Web-http: //www.mipro.com.tw E-mail: mipro@mipro.com.