User Guide ACT-30T Bodypack Transmitters All rights reserved. Do not copy or forward without prior approvals MIPRO. Specifications and design subject to change without notice.
WARNING ! IMPORTANT SAFETY INSTRUCTIONS ! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Bodypack Transmitter Bodypack Transmitter Contents 1 Bodypack Controls and Indicators 3 Operating Instructions 4 LCD Display Screen 5 Transmitter Parameters 12 Battery Status 13 MUTE Control Set-Up 15 AF Input Connections 16 Battery Removal and Installation Bodypack Controls and Indicators 1 2 3 4 5 6 7 8 GRP CH 07 03 12 13 9 10 11 0 1 Audio Input Connector: TA4F mini 4-pin connector accepts any MIPRO lavalier, instrument and headset microphones and cables.
Bodypack Transmitter 3 Antenna: Flexible 1/4 wave transmitting antenna. 4 Transmitter Housing: Holds PCB board and wires. 5 LCD Panel: Display transmitter parameters. 6 SET Button: Parameter selection button. 7 MODE Button: Allows access to 7 available functions displaying in LCD panel. Bodypack Transmitter Operating Instructions ! The audio gain level is factory preset at Microphone-Low level. Guitar setting is recommended at LINE level.
Bodypack Transmitter Bodypack Transmitter LCD Display Screen Transmitter Parameters MODE button ! GRP 07 03 A1 A2 Press “MODE” button to access one of the 7 parameters below. CH AF MUTE A1 LCD Screen A2 AF (audio) MUTE A3 Transmitter Battery Meter SET button ! A3 Press “SET” button then the changeable functions will twinkle. Change to the desired parameters during the above twinkle by pressing “SET” button.
Bodypack Transmitter ! Bodypack Transmitter Frequency Band, Group & Channel and Frequency are factory pre-set, thus, its parameter values are displayed after it is ACT synced. Values cannot be changed. Setting Input Sensitivity Level BAND 8A GRP ! 4 Selectable Sensitivity Levels: LINE、 MIC-L (MICROPHONE-LOW)、 MIC-M (MICROPHONE-MID)、 MIC-H (MICROPHONE-HIGH). ! Press MODE button until AF GAIN mode appears. (Frequency Band) ! Press SET button once to activate function.
Bodypack Transmitter Bodypack Transmitter Setting RF Output Power MUTE MODE ! 2 RF Output Power Levels: RF-LOW and RF-HI. ! ! Press MODE button until RF POWER LOW or RF POWER HIGH mode appears. MUTE MODE: Select from MANUAL and DISABLE. ! Press MODE button until MUTE MODE appears. Press SET button once, the LCD screen starts flashing to denote it is ready to accept mode changes. Press SET button to change between MANUAL and DISABLE in cycle.
Bodypack Transmitter Bodypack Transmitter ERR Message Setting LOCK ! Setting LOCK can be switched to LOCK or UNLOCK mode. ! Press MODE button until SET LOCK mode appears. ! Press SET button to select the desired parameter. ! Press MODE button to confirm and save the change. ! Press SET button twice to remove the LOCK function. ! The LOCK function will be removed automatically when losing power. ! Mute function can still work properly when LOCK.
Bodypack Transmitter Bodypack Transmitter Battery Status MUTE Control Set-Up Indicates the power remaining in the transmitter battery. When the battery has less than 10% power remaining it must be replaced or recharged. If an under voltage condition continues, the LCD will show “OFF...” and the system will shut down to prevent being overly discharged. MUTE control enables audio to be muted or unmuted temporarily. 100% 80% 60% 40% 20% ! Press MUTE button to mute audio temporarily.
Bodypack Transmitter Bodypack Transmitter AF Input Connections External Mute Connector ! External mute connector is a 3.5mm jack. When an external mute switch cable, MJ-70 (optional) is connected, user can manually mute and unmute the audio temporary.
Bodypack Transmitter Bodypack Transmitter & IC - ID Battery Removal and Installation Pushing down both snap locks on the sides to open battery compartment cover. Take out the two batteries. (Figure 3) Insert two fresh AA batteries (alkaline type is recommended) into the battery compartment according to the correct polarity (- and +) as shown in (Figure 4). Then close the battery compartment cover tightly. THIS DEVICE COMPLIES WITH PART74 OF THE FCC RULES AND RSS-123 ISSUE2 OF CANADA.