ACT-80H Wideband Digital Handheld Transmitter User Guide MIPRO Electronics Co., Ltd. Headquarters: 814 Pei-Kang Road, Chiayi, 60096, Taiwan. Web: www.mipro.com.tw E-mail: mipro@mipro.com.
IC: Wideband Digital Handheld Transmitter This device complies with Industry Canada RSS-123 ISSUE 2 standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter Key Features ! Innovatively designed housing in MIPRO's aesthetics and ergonomic style. ! Perfect combination of digital audio and wireless transmission technology creates perfect sound quality. ! Metal housing shows professional elegance look and features solid grip and balanced weight. ! Patented design of the grille and battery housing being integrated.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter 1 Capsule Module: Protects detachable microphone capsule module and internal foam prevents breathing, wind and POP noises. Bodypack Controls and Indicators 1 2 Battery Compartment: Holds 2 'AA' batteries. 3 Housing: Protects transmitter PCB, battery compartment and batteries. 4 LCD Panel: Displays transmitter parameters.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter Patented Protection Cover Operating Instructions for Insertion & Removing Battery ! Turn the microphone housing and pull it toward capsule grille to expose battery compartment. ! Insert two new AA alkaline batteries in the battery compartment with correct polarity orientation. ! Turn power switch to ON position after battery installation. If LCD does not lit, please check battery polarity or change to fresh batteries.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter LCD Display Screen ! Channel identification clip can be attached to the bottom of protection cover.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter How to Setup Transmitter Parameters ! Remove protection cover to expose MODE button and SET button. ! MODE Button: Press “MODE” button to access one of the six functions below. ! B C GRP CH FREQUENCY AF GAIN 01 02 486.500MHz 0 dB A SET Button: Press “SET” button and LCD wills start flashing. During flashing, press SET button to change parameters. SET FREQUENCY 486.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter GRP CH: Displays Group and Channel Information a. Press MODE and stop on the GRP CH function; the display showing the current group and channel will be flashing. After 5 seconds, the display will stop flashing and the current group and channel selection will be set. CH 01 02 a. Press MODE and stop on the FREQUENCY function; the display showing the current frequency will be flashing.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter AF GAIN: Setup and Change of Input Sensitivity a. Press MODE and stop on the AF GAIN function; the display showing the current status will be flashing and is ready to be modified. b. Every push of the SET button increases the dB value by 3dB to a maximum of 6dB. AF LOW-CUT: Setup and Change of Low Frequency Cut Off a.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter AF LIMIT: Setup and Change of Input Limit ENCRYPTION: Displays Information of Encryption a. Press MODE and stop on the AF LIMIT function; the display showing the current status will be flashing and is ready to be modified. a. Press MODE and stop on the ENCRYPTION function; the display showing the current status will be flashing. b. Press SET while the display is flashing to change the setting to ON or OFF. **NOTE: 1.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter RF POWER: RF Power Selection MUTE MODE: Mute model selection a. Press MODE button for selection of RF POWER. Selection of RF-HI or RF-LOW can be selected once the RF POWER LCD starts blinking. a. Press MODE button for selection of MUTE MODE. Selection of MANUAL or AUTO or DISABLE can be selected once the MUTE MODE LCD starts blinking. b. Press SET button to select and set RF-HI or RF-LOW. b.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter Battery Status MUTE MODE MUTE MODE MUTE MODE MANUAL AUTO DISABLE MUTE MODE MANUAL Indicates the power remaining in the transmitter battery. When the battery has less than 10% power remaining it must be replaced. If an under voltage condition continues, the LCD will show “OFF...” and the system will shut down to prevent being overly discharged.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter Power Button ERR: Error Code ! Turn the power switch to ON position where transmitter will be activated and LCD will lit up. ! Turn the power switch to OFF position to shut down the transmitter. ! When the power switch is turned off, the LCD will show “OFF...” (for Power Off) first and then the system will shut down and no further messages will be displayed.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter Setting MUTE ! ! B C GRP CH FREQUENCY AF GAIN 01 02 486.500MHz A Press MUTE button to enter mute status. At mute status, AF indicators will become “AF MUTE” and blink continuously. All the functions can be operated and ACT can be activated at the mute status. All the operations of functions are the same with the ones at regular status.
Wideband Digital Handheld Transmitter Wideband Digital Handheld Transmitter General Tips for Improving System Performance 1. Performer should avoid holding the microphone over or near the antenna section as this will deteriorate transmission efficiency. Severe deterioration if performer directly covers up the antenna section with both hands. 2. Many performers tend to hold the microphone by the top grille.