User guide
Personal Wireless Public Address System Personal Wireless Public Address System
18
19
Corresponding Channel Display: MA-100 Receiver and Transmitter
MA-100
1
2
3
4
5
6
7
8
Transmitter LCD
01 01 01 02
01 03
01 04 01 05 01 06 01 07 01 08
9 0
A B C D E F
MA-100
01 09 01 10 01 11 01 12
01 13
01 14 01 15 01 16
Transmitter LCD
ACT Synchronization (Sync) between Receiver and Transmitter
Channels:
! Power on handheld or bodypack transmitter. Ensure fresh batteries are properly
installed with correct polarity.
! Locate and bring the transmitter sync port (red indicator) within 30cm (12-inch) of
CH 1 or CH 2 receiver sync port or .
! Press and release SCAN/ACT button to synchronize receiver and transmitter
channels (See diagram 1)
! During syncing, the channel indicator in CH 1 or CH 2 will blink and LCD on
the transmitter will display corresponding four digital numbers
(see Corresponding Channel Display: MA-100 Receiver and Transmitter on page 18)
! When the channels are synchronized the channel indicator in channel screen stops
blinking and RF indicator or glows green to indicate a successful RF link.
! The transmitter is now set to the new channel and ready for operation.
! Repeat steps if channel indicator remains flashing and no glowing green RF indicator.
(Figure 1)
22
29
25 26
23
28
PLAY /
PAUSE
STOP
REC
POWER
PRV / TEN NEXT / TEN
RF
CH2
USB
SCAN / ACT
CH1
RF
RECEIVER
SCAN / ACT
LINE VOLPOWER/ MIC VOL
DC IN
USB VOL LINE OUT
OFFOFFOFF OFF
MIC IN
LINE IN
CH2 VOLCH1 VOL
ALARM
MIs ong_m . mp3
ROCK
02:55
03:54
012
068
MP3
256
A
or
<
3
0c
m
(
1
2
in
.)
<
30
cm (1
2 in.)
or
RF
CH2
SCAN / ACT
CH1
RF
RECEIVER
SCAN / ACT
OPERATING INSTRUCTIONS
Wired Microphone
! Plug optional MIPRO MM-107 wired dynamic microphone with a 6.3mm (1/4”)
connector to MIC IN.
! Turn on master POWER/MIC VOL and adjust to desired volume.
Line-Input
! Available to connect an external CD, MP3, iPod or cassette player.
! Connect a 3.5mm-to-3.5mm audio cable (not included) to the LINE-IN jack.
! Turn on master POWER/MIC VOL.
! Adjust LINE VOL to desired volume.
Play USB Drive
Insert USB drive into USB 2.0 port.
Turn master POWER/MIC VOL power on.
Turn USB VOL power on. Display screen will light when USB player is turned on.
Press & release NEXT/TEN button for next track. Press & hold NEXT/TEN button
skips forward next 10 tracks.
Press & release PRV/TEN button for previous track. Press & hold PRV/TEN button
skips backward previous 10 tracks.
Two optoins for the order of playing music
Copy the desired songs into USB storage unit one by one until copying all the
desired songs. By this way, the play sequency will be based upon the order of music
being programed into USB storage unit.
If the desired songs will be divided into different folders, please number the songs
when copying them into folders then copying the said folders into USB storage unit.
Pleae note the songs must be numbered by the same digit like 00, 01, 02 or 000,
001, 002 or 0000, 0001, 0002... and so on.
Format USB and SD card before playback. Format standard is FAT.
!
!
!
!
!
!
!
!