User guide

ManualsBrandsMira ManualsHome building and DecorSHOWER FITTINGS

Installation & User Guide

SHOWER FITTINGS

These instructions are to be left with the user

MIRA ADVANCE

Summary of content (20 pages)

PAGE 1
MIRA ADVANCE SHOWER FITTINGS Installation & User Guide These instructions are to be left with the user 1
PAGE 2
ConTENTS Introduction............................................................................................ 3 Specification.......................................................................................... 4 Pack Contents ...................................................................................... 5 Dimensions............................................................................................ 6 Installation......................................................................
PAGE 3
Introduction The Mira Advance Shower Fittings Mira Advance shower fittings are precision engineered to give a great shower over a range of pressures. The Advance shower fittings can be fitted onto a flat wall or fitted into a corner position, to satisfy and compliment various shower areas. Wall Mounted Corner Mounted Product covered by this Guide: Advance Complete Fittings - An adjustable spray handset, flexible hose, adjustable clamp bracket assembly, slide rail, hose retaining ring and soap dish.
PAGE 4
SPECIFICATION Specifications Minimum maintained pressure: 6 kPa (0.06 Bar). Maximum maintained pressure: 500 kPa (5.0 bar). Warning! Exceeding the stated maximum maintained pressure could result in excessive spray forces and possible damage to the product. Pressure loss = Pressure difference between the inlet and outlet of the fitting 26 24 Flow Rate (Litres/Minute) 22 Force 20 Start 18 16 Soothe 14 12 Eco 10 8 6 4 2 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.
PAGE 5
Pack CONtents  Tick the appropriate boxes to familiarize yourself with the part names and to confirm that the parts are included.
PAGE 6
DIMENSIONS 322 86 Flex Version 1000 658 600 23 56 176 All dimensions in mm 6
PAGE 7
INSTALLATION General Make sure that the shower fittings are installed by a competent installer. Installations must comply with Water Regulations (Bye-Laws, Scotland), and any Local Regulations and Building Regulations in force at the time of installation. Before installation carefully inspect the new fixture for any signs of damage. The slide rail should be positioned to one side of the shower control at a convenient height for all the family. The slide rail can be fixed to a flat wall or into a corner.
PAGE 8
2. Carefully remove the protective film from the slide rail. 3. Holding the clamp bracket, squeeze the sides together and push the clamp bracket onto the slide rail. Slide Rail Support Long Edge Clamp Bracket Note! It is important that you slide the shorter edge of the clamp bracket onto the slide rail. 4. Slide the hose retaining ring onto the slide rail. 5. Push the slide rail supports onto each end of the slide rail assembly.
PAGE 9
6. Hold the slide rail assembly against the wall in the desired position. Note! If fixing the slide rail into a corner see "Corner Mounting" page 13. 7. Use the slide rail supports as a template and mark the positions of the top and bottom fixing holes. Note! When marking the position of the holes, if using the vertical oval hole on the top of the slide rail, then use the horizontal oval hole on the bottom fixing. This will allow you to make slight vertical and horizontal adjustments to the slide rail.
PAGE 10
. Fit the wall plugs. Wall Plug Wall Screw 11. Hold the slide rail against the wall and gently screw the slide rail into position. Check that the slide rail is vertical and make any adjustments before fully tightening the wall screws. Clamp Bracket Hose Retaining Ring Slide Rail Support Cover 12. Push on the slide rail support covers.
PAGE 11
13. Align the notch on the soap dish with the recess on the hose retaining ring. 14. Push the soap dish onto the hose retaining ring. Notch Recess 15. To lock the soap dish into position twist the soap dish to the right or if preferred twist to the left. Note! If space is limited, you do not have to fit the soap dish to the hose retaining ring, but the hose retaining ring must be fitted.
PAGE 12
16. Attach the hose onto the handset. Make sure that the hose washer is fitted and do not overtighten. 17. Pass the hose through the hose retaining ring and soap dish (if fitted). 18. Attach the hose to the outlet of the shower control. Make sure that the hose washer is fitted. 19. Place the handset into the clamp bracket. Wall Mounted Handset Holder (Advance Flex Only) 1. The shroud must be removed to fix the handset holder to the wall.
PAGE 13
Corner Mounting 1. For corner mounting first follow instructions on pages 7 and 8, steps 1 to 6. 2. Hold the slide rail assembly against the wall in the desired position. 3. Use the slide rail supports as a template and mark the position of the two top fixing holes and the two bottom fixing holes. Note! Check that the slide rail supports are sitting on both walls before drilling fixing holes. 4. Drill two 8mm fixing holes at the top of the slide rail and two at the bottom of the slide rail.
PAGE 14
OPERATION Adjustable Handset Operation The handset has four different spray modes, Eco,Start, Soothe and Force. The handset has a combined checkvalve and flow regulator fitted in the handset. The handset operation is described below: 1. Eco: Water flows from the outer set of holes at a reduced flow rate to save water. To select the Eco setting, turn the spray plate fully clockwise. 2. S t a r t : Tu r n t h e s p r a y p l a t e anticlockwise until it 'clicks'.
PAGE 15
MAINTENANCE Cleaning Many household cleaners contain abrasives and chemical substances, and should not be used for cleaning plated or plastic fittings. These finishes should be cleaned with a mild washing up detergent or soap solution, and then wiped dry using a soft cloth. 1. To remove limescale, use your thumb or a soft cloth to wipe any limescale from the soft rubber nozzles and the front face of the showerhead. Spray Plate Assembly - Internal 1. 2. 3. Remove the spray plate assembly.
PAGE 16
Spray Plate Assembly-Removal 1. Tu r n t h e a d j u s t e r r i n g f u l l y anticlockwise. 2. Unclip and remove the adjuster ring. 3. Unscrew the spray plate assembly in an anticlockwise direction. The 'O' seals will provide some resistance. 4. Remove the inner and outer nozzle retaining rings. Handset Body Assembly Outer Nozzle Retaining Ring Inner Nozzle Retaining Ring Spray Plate Assembly Nozzle Ring Removal Adjuster Ring 1. Carry out instructions 1 to 4 of "Spray Plate Removal".
PAGE 17
FAULT DIAGNOSIS The trouble shooting information tabled below gives details on what you can do as a user, should you encounter difficulties with the shower fittings whilst operating the shower. Before replacing any parts make sure that the underlying cause of the malfunction has been resolved. Malfunction Cause Remedy The spray plate assembly is blocked. Refer to the ‘Cleaning’ section. The hose is blocked or twisted. Clear blockage or replace the hose. Problem with the shower control.
PAGE 18
SPARES 450.08 Service Pack 'O' Seals - components identified 'A' 632.73 Hose Washer 1603.098 Handset (White) 1603.102 Slide Rail Supports ( x 2 ) 1603.103 Soap Dish and Hose Retaining Ring 1603.104 Chrome Hose - 1.25m 1603.106 Chrome Hose - 2m (Flex Product) 1603.112 Mounting Pack 1603.113 Slide Rail 06 Satin 1603.114 Slide Rail 10 Satin 1603.115 Adjuster Ring - White 1603.116 Spray Plate Assembly 1603.120 Wall Mounted Handset Holder 1603.131 Adjuster Ring (Grey) 1603.
PAGE 19
Mira Advance Shower Fittings Spare Parts Diagram 1603.102 8 .12 03 98 16 03.0 16 6 .11 03 16 1603.112 A 632.73 1603.115 1603.131 1644.124 1603.132 1603.113 1603.114 1603.120 1603.103 1603.104 1603.