SDS

P R O DU C T D AT A S H E ET
www.miraclesealants.com
Grout Sealer
02-2009
Water & Stain Protection For
All Sanded & Non-sanded Grout and Mortar Joints.
U
ses
■
Kitchen Counters
■
Kitchen Floors
■
Bathroom Showers
■
Bathroom Floors
■
Service Porches
Special Features
■
Easy To Use
■
Interior & Exterior Use
■
Weather Resistant
■
F
reeze/Thaw Resistant
■
S
alt Water Resistant
■
A
cid Resistant
■
Non Yellowing
■
U.V. Transparent
■
Less Slippery
PRODUCT DE SCRIPTION
KEEP OUT OF REACH OF CHILDREN. Grout Sealer is designed for the pro-
tection of all sanded, non-sanded and mortar joints. Grout Sealer pene-
trates into the surface and forms an invisible barrier that is resistant to
moisture and stains, while allowing vapor to escape. Grout Sealer is not a
surface coating and will not alter the natural look. Grout Sealer can be used
on interior and exterior applications. Grout Sealer is U.V. transparent and
will not yellow under any circumstances.
NOTE: For any question concerning grout-refer to the manufacturers specifi-
cations.
Sample Testing
Due to the differences of each material, several inconspicuous test patches
should be completed to assure maximum performance. User must deter-
mine suitability of the product for their intended use.
Grout Color Modification
For changing the color of sanded, epoxy and non-sanded grout joints use
the Grout Color Kit.
Protect Neighboring Surfaces
Always protect neighboring surfaces including wood, carpet, metal, land-
scaping and other non masonry surfaces.
NEW INSTALLATIONS - APPLIC ATION INSTRUCTIONS
Read entire label and PDS/MSDS before using. Grout Sealer should not be
diluted or thinned in any way. Grout Sealer should be used as is direct from
approved container.
Grout or mortar must be cured per manufacturers specification before
applying Grout Sealer. Apply Grout Sealer with it’s unique applicator tip
directly to the joint for maximum stain resistance. Any excess sealer that
gets on tile or stone surface should be wiped off with a clean towel before it
dries. Be careful not to allow sealer to puddle on surface.
Existing Installation - Surface Preparation
Grout or mortar surface must be dry and free of contaminants, including
previously applied sealers, dirt, lime & hard water deposits, efflorescence,
rust & other heavy dirt and grime.
Floor Coating/Wax Removal
To remove existing coatings and/or waxes use Mira Strip or H2O Strip per
the instructions.
Heavy Duty Cleaning:To remove lime and hard water deposits, efflores-
cence, rust and other heavy dirt and grime use GCFR (Grout & Concrete
Film Remover), Phosphoric Acid Cleaner or Porcelain Ceramic Tile Cleaner
following the instructions carefully. If an additional non acid deep cleaning
is necessary use Liquid Poultice as directed. All strippers and/or cleaners
should be thoroughly rinsed with clean water and the materials allowed to
dry.
Light Duty Cleaning: Use Grout Cleaner, Mira Clean #1 or Counter Kleen as
directed.
Mold, Mildew and Bacteria Sanitation
For best results in killing mold, mildew, bacteria and other micro organisms,
use Miracle Wipes as directed.
Residue Removal
To remove accumulated Grout Sealer residue, use Residue Remover as
directed.
Existing Installation - Application Instructions:
Follow the application instructions previously mentioned.
Coverage
Coverage will vary depending on the density porosity, texture, surface
a
bsorption, weather, time solution left on the surface and application meth-
ods. Used as directed, Grout Sealer will cover approximately 60 - 115
square feet per 6 oz. bottle (5 sq. meters per 14 milliliters).
Cure Time
Grout Sealer will be dry to the touch in 1 - 3 hours and may be put into ser-
vice. For optimum results the area should be kept dry and free from staining
materials for 72 hours.
MAINTENANCE
For ongoing maintenance instructions please refer to Miracle Sealants Care
Guide. Refer to the Miracle Sealants Product Recommendation Chart for
specific product recommendations.
Storage
Store Grout Sealer in the original container, properly sealed to avoid conta-
mination and solvent evaporation. Stored at 77
0
F (40
0
C), Grout Sealer will
have a shelf life of 12 months.
Technical Support
For additional technical support, contact Miracle Sealants Company at
1-800-350-1901 or 626-443-6433 ext. 3013
Office Hours
Monday - Friday from 8:30 am - 5:00 pm PT.
1-626-443-6433 or 1-800-350-1901 • Fax: [phone]
website: www.miraclesealants.com
Product Damaged During Transportation
If product is damaged during transportation contact
Info Trac @ 1-800-535-5053
Additional Products
Miracle Sealants Company offers a complete line of water & stain
repellents, sealers, cleaner, polishing compounds, diamond abrasives,
machinery and accessories for the tile, stone, concrete, metal, fabric and
carpet professional or do-it yourself specialist.
Warranty
Instructions are a condensed guide and should not be considered com-
plete. In the event of failure, the only obligation of Miracle Sealants
Company shall be to replace such products proven to be defective. Before
using, user shall determine the suitability of the product for their intended
use User assumes all risks and liability whatsoever in connection therein.
Neither seller nor manufacturer shall be liable for any injury or inability to
use this product.
Caution
Grout Sealer contains combustible petroleum distillates. All solvents must
be considered toxic and must be used in a well ventilated area. Good venti-
lation means that fresh air is flowing in such a way as to feel a slight breeze.
Use open windows and use fans to circulate air. Continue to ventilate until
vapors are eliminated. Exposure to high vapor concentration must be avoid-
ed. Inhaling the vapors can be harmful. Keep away from heat and open
flames. Avoid prolonged contact with skin. Chemical resistant gloves should
be worn at all times. Keep small children and pets out of area until product
or surface has thoroughly dried. Refer to the MSDS for additional informa-
tion.