Installation Guide

STEP 1
STEP 1 Spread adhesive using a 1/2in (12.7mm) notch trowel.
STEP 2 A&B
Lay tiles and insert appropriate Spacer/Anchor. Cross
Spacer (+)(shown) are used in the intersection for straight
grid patterns, Tee (T) for brick grid patterns, and Flat (-) for
the edges at walls.
STEP 3 After Spacers/Anchors are installed, place Caps over the
Spacer/Anchor firmly.
STEP 4 Slide the Evolver Tool onto the Spacer/Anchor and pull
trigger to apply tension between the Cap and tile until the
Cap is firmly holding tile. The tension knob at rear of gun
can be turned clockwise to decrease tension or counter
clockwise to increase tension. This is adjustable so you
can adjust for various thicknesses of tile or stone.
LET TILES FULLY SET (Per Manufacturer’s Setting Material
Instructions)
STEP 5 REMOVING REUSABLE CAPS & DISPOSABLE
SPACER/ANCHORS
WALLS To remove Caps and Spacer/Anchors after tiles
have fully set & cured, wind adjuster knob counter clock-
wise on the Evolver Tool to adjust to maximum tension.
Place Evolver Tool back on Spacer/Anchor and pull trigger
until Spacer/Anchor breaks off to fully remove.
FLOORS Spacers/Anchors can be kicked (parallel to the
spacer) to break off in order to save time. Once Spacer/
Anchor is broken off Caps can be removed with the De-
capper Tool for reuse. On softer Natural Stones & Tiles
use Evolver Tool only to remove Caps and Spacer/
Anchors as explained above for walls.
STEP 6 To reuse Caps, insert Decapper Tool and place tapered
end (tip) between the Cap and strap/anchor to loosen
teeth. Slide the center slot through the Spacer/Anchor and
hook under Cap. Push down with thumb while supporting
the Cap with index finger and slide Cap upwards removing
the Cap from the Spacer/Anchor. Discard the disposable
Spacer/Anchor and keep Cap for reuse.
WALLS Always place Spacer/Anchor in a vertical position (Cross
as shown in diagram) or horizontal position (tee or flat) to
avoid chipping tiles when removing.
A Complete Tile Spacing & Leveling
System in One!
The Efficient way to Space & Level
Floor & Wall Tiles
Miracle Sealants Levolution is a revolution in Tile Spacing &
Leveling Systems for all tiles, especially large-format tile. Levo-
lution is an all in one system and can be used for both floor &
wall installations! It’s Spacer/Anchor comes in 3 sizes to accom-
modate for a 1/16”, 1/8” or 3/16” grout joint. It comes in 3 dif-
ferent profiles which include Cross (+) for straight grid patterns,
Tee (T) for brick grid patterns and Flat (-) for edges at walls
for all patterns. Levolution can be used with tile or stone with
thicknesses up to a ½” inch.
Levolution requires only one piece per intersec-
tion regardless of the tile size so you are laying tiles
instead of extra spacers saving you time and money. Other
systems on the market require up to 4 pieces per intersection
and an additional piece every 12” with large format tiles. Levo-
lution has the least expensive component cost per square foot
and saves up to 51% in labor over other systems. Levolution
allows anyone to install evenly spaced and level tiles and can
be used by both the professional and DIY user. Join the revo-
lution today!
levolution
STEP 2 - A
STEP 3
STEP 4
STEP 5 - WALLS
STEP 6
STEP 2 - B
WALLS
STEP 5 - FLOORS
LET
TILES
FULLY
SET
Visit www.miraclesealants.com/levolution to view product video
INSTALLATION:
On softer Natural Stones
& Tiles use Evolver Tool
ONLY to remove
Caps and Spacers.
levolution
A revolution in tile spacing and leveling!
Levolution Brochure rev16.indd 1-4 11/28/17 10:35 AM