SLIDING DOORS INSTRUCTION M A N UA L
THANK YOU FOR PURCHASING THE MIRADOR SLIDING DOORS! This manual will provide you with clear and detailed instructions on how to safely and correctly assemble and maintain your sliding doors, to ensure it brings you many years of use and enjoyment. IMPORTANT Please read the entire manual carefully before installing and using your sliding doors, and please ensure the manual is kept in a safe place for future reference.
TABLE OF CONTENTS 2 - Before Assembling Your Sliding Doors 3 - Important Safety Advice 5 - List of Parts 7 - Installation 9 - Enjoy Your Sliding Doors 19 - Care & Maintenance 20 - Warranty & Complaints Procedure 21 - Certification Information 22
BEFORE ASSEMBLING YOUR SLIDING DOORS WARNING: Improtant safety instructions. Follow all instructions, since incorrect installation can lead to severe injury. Make sure you have all the tools required for assembling your sliding doors In order to assemble your sliding doors safely and correctly, please ensure you have access to the following tools and accessories, all of which are not provided.
Select a suitable location: The ground should be solid and flat The ground should be level The sliding doors must be positioned and fixed on a properly installed Mirador pergola, which is installed on a flat concrete ground, providing proper stability. >2.5° Warning: Most terraces or patios are designed with a slight slope to prevent (rain) water from forming pools or reaching the house or other structures.
IMPORTANT SAFETY ADVICE For the safety of all persons installing and using the sliding doors , it is important to follow the safety guidelines below. Open the sliding doors during severe weather conditions which include high winds. Always wear appropriate work shoes, gloves and eye protection when working. Work well away from power lines, particularly when handling metal parts. If using power tools or a ladder, always follow the manufacturer’s safety instructions.
Do not assemble the sliding doors when you find damaged parts or any parts missing. Only use replacement parts that are approved by the manufacturer. Please recycle packaging where possible. After prolonged use we recommend you check all the fittings are tightened securely. Install on non-Mirador branded pergola will void the product warranty and can damage the operation mechanism. Mirador® Approved lt is recommended that two people lift the top track once assembled.
LIST OF PARTS REF Part Name QTY A Sliding panel A 1 C Sliding panel C 1 REF Part Name QTY B Sliding panel B 1 D Sliding panel D 1 7
REF 8 Part Name QTY E Top track 2 F Side frame 2 G Bottom track 2 H Connecting pipe 1 I Screw Cap 4+1 J Plastic Expansion Pipe 8x40mm 4+1 K Screw ST4.2x38mm 4+1 L Screw ST3.9x13mm 2 M Screw ST4.
INSTALLATION 1. Track and frame assembly Installation Video Sectional view 1A Hang the 2 top tracks Fasten top track screws M E over the beam. to beam with 4 E , using electric screwdriver. E M x4 E x2 M 1B Position the side frame F to the pillar. The side wall of the side frame F is attached to the inside of the top track E .
1C M Fix the side frame with 5 screws M M F to the pillar by using an electric screwdriver. F F x5 1D Repeat steps side frame F 1B - 1C to install the onto the other pillar.
1E Slide 2 bottom tracks G G into the connect pipe until their ends meet. Make sure the screw holes on both G and H are aligned, and fix H G L x2 H x1 G x2 H and H together with 2 screws L by using an electric screwdriver. L 1F Position the bottom track G against the pergola pillars. Notice: The side wall of the bottom track G is attached to the inside of the side frame F . Mark the position of the drill holes on the ground with pencil.
1G Remove the bottom track G , drill holes with hammer drill and knock in the plastic expansion pipe J with hammer. G J J x4 1H Put the bottom track K back to the position. Fixed the bottom track G to the ground with 4 screws K G and cover the screws with 4 screw caps I .
2. Door assembly 2A Sectional view Attention: and bottom track G . Each track has two slides. Sliding panels B and C are installed Top track E on the outer slides Sliding panels A and D E-1 / G-1 / G-2 . are installed on the inner slides E-2 . Sectional view E-1 B/C E-2 G A/D E B/C A/D G-1 G-2 Before installation, please ensure the correct positioning of the slides on the track and the orientation of the door lock.
2C A Lift sliding panel A up into the inner slide of the track . Swing the bottom in and tuck the sliding panel down into the bottom track G-2 . Please note the orientation of the lock side. E-2 E-2 A A A G-2 A x1 2D Repeat step 2C to install the rest sliding panels.
C E-1 C C C G-1 Attention: Sliding the panel C towards B to leave enough space for the installtion of Panel D .
D E-2 D D D G-2 16
3. Adjust your sliding doors 3A You'll find screws on both sides of the door near the bottom, which can be used to adjust the height of one side. To raise that side, turn the screw clockwise. To lower that side, turn the screw counterclockwise. Using a Philips screwdriver.
4.
ENJOY YOUR SLIDING DOORS Remove the inner (transparent) and outer (white) film on the sliding panels.
CARE & MAINTENANCE Dust and dirt will collect on the PC panel and will require periodic cleaning by water, then air dry or wipe with 100% cotton cloth. After gently wiping the stains on the PC panel with alcohol based cleaner *, rinse it clean with water. In coastal areas, it is recommended that you Always test cleaners in a small inconspicuous frequently spray the screen with water to area prior to cleaning entire panel to prevent reduce accumulation of salt and dirt. adverse results.
WARRANTY & COMPLAINTS PROCEDURE For terms and conditions of our limited warranty, please visit www.miradoroutdoor.com or contact your local Mirador sales representative. Complaints procedure: • The complaint must include an order number or transaction number. Goods without an order number or transaction number are not covered under the warranty. • The complaint must include a detailed description of the defect, the name of the company which installed the product and the date when the defect was discovered.
CERTIFICATION INFORMATION Declaration of performance (DOP) Reference no. DOP0004 Product name and type Mirador Panel shutter / Sliding shutter Model name/ Unique identification code of the product: 111 Shutter Wall Am, 111 Louver Wall Am, 111 Sliding Shutter Wall Am, 111 Sliding PC Wall Am, A: 3, 3.6, 4 Purpose of Usage: External use in buildings and other construction works Manufacturer: Zhejiang Zhengte Co., Ltd.
23
