Robotic Vacuum Cleaner Operation Manual M680GMA
TABLE OF CONTENTS SAFETY INSTRUCTIONS ---------------------------------------------------- 2 * Safety Instructions * FCC Caution * Battery and Recharging Instructions WARNING ------------------------------------------------------------------------ 9 SPECIAL FEATURES -------------------------------------------------------- 10 MAJOR COMPONENTS AND ATTACHMENTS ------------------------ 10 M680GMA OVERVIEW ----------------------------------------------------- 11 INSTALLATION GUIDE ------------------------------
SAFETY INSTRUCTIONS Please read the safety instructions in the Operation Manual before operating M680GMA and keep this manual handy for your future reference. Observe the basic safety rules to prevent any occurrence of fire, electric shock and personal injury. Safety Instructions: 1. Please read the Operation Manual before operating M680GMA. 2. Do not operate M680GMA outdoors. 3. Before starting M680GMA, be sure to install M680GMA dust bin filter properly in case of any damage of M680GMA. 4.
SAFETY INSTRUCTIONS 7. Never use M680GMA to clean up sparking cigarette butts or burning ashes from fireplace. 8. Never use M680GMA to clean up combustible or highly volatile liquids such as gasoline. 9. While M680GMA is in operation, make sure all doors leading outside are closed. 10. During operation, the heat vent should avoid being clogged. If heat vent clogged, M680GMA could be damaged. 11. If M680GMA is malfunctioned or damaged by force, do not operate M680GMA regardless the cause.
SAFETY INSTRUCTIONS 14. WARNING: the plug must be removed from the socket-outlet before cleaning or maintaining the appliance. 15. Automatic battery-operated cleaners shall also be provided with cautionary instructions for room preparation and constant care. 16.
SAFETY INSTRUCTIONS FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
SAFETY INSTRUCTIONS RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
SAFETY INSTRUCTIONS Battery and Recharging Instructions: 1. Please apply the same model’s battery (D.C. Lithium-ion 14.8V 2900mAh) and adaptor (20V 1200mA) as equipped with the packing. 2. The external flexible cable or cord of this adaptor cannot be replaced; if the cord is damaged, the adaptor shall be scrapped. 3. When placing the batteries into the reservoir, please be sure that the polarity (+/- sign) of the batteries match with the indication marked inside the battery reservoir.
SAFETY INSTRUCTIONS 11. If M680GMA requires cleaning, unplug the adaptor, switch off the unit and take out the battery. 12. The battery must be removed from the appliance before it is scrapped. 13. The appliance must be disconnected from the supply mains when removing the battery. 14. The battery is to be disposed of safely. Attention should be drawn to the environmental aspects of battery disposal. Don't throw used batteries in dustbin. Please contact your retailer in order to protect the environment. 15.
WARNING Following objects are strictly banned, otherwise the vacuum cleaner will be damaged or fire calamity will be caused, which bring such accidents as human body injuries: - Don’t pick up large or sharp broken such as glasses. - Don’t pick up harming or erodent liquids (solvent, corrosive, detergent…). - Don’t pick up inflammable or explosive substance such as gasoline or alcohol. - Don’t pick up/ vacuum burning or glowing objects (cigarettes, matches, hot ashes).
SPECIAL FEATURES Congratulations on purchases the M680GMA Robotic Vacuum Cleaner. This revolution Robotic Vacuum Cleaner is equipped with functions suitable for cleaning up floor surfaces of home and office such as wood, tile, and linoleum. M680GMA Robotic Vacuum Cleaner is a household helper. Working Patterns: "Z" Type Along the wall With Gyro and main wheel encoder sensors, M680GMA could build the simple map so It could clean your rooms and back to the dock station successfully when its power is low.
M680GMA OVERVIEW IR Receiver (for Docking Station) Control Panel and LED Display Top Cover (Dust Bin in Side) Bumper Power Switch D.C.
INSTALLATION GUIDE Installing and Removing Side Brush: To install: Push the brush directly onto the holder.(Fig. 1) To remove: Hold two opposite sides of the brush as shown in Fig. 2, and evenly pull upward to remove the brush. PULL UP! Side brush holder PRESS CLICK! Fig. 1 Fig.
INSTALLATION GUIDE Battery Installation and Removal: 1. Turn off the power switch before installing the battery. 2. The details on how to remove the battery: To open the battery cover first by pressing the two points “A” (marked in the below diagram) and slide the battery cover in the direction of arrow “B” (marked in the below diagram). Then push the battery toward the springs’ side in order to take out the battery easily. 3.
INSTALLATION GUIDE Recharging Battery: 1. Before charging, please check if the battery is properly mounted and turn on the power switch. 2. Two ways to charge the battery: A. Push the adaptor plug into d.c. jack at the side of the unit first, and then plug the a.c end of the adaptor into the a.c. power outlet on the wall. (Please connect the adaptor to the unit first before connecting to the a.c power outlet.) Adaptor Plug D.C. jack B.
INSTALLATION GUIDE Proof Test: Please try to test the installation of docking station, if the vacuum cannot go back to the docking station and charge successfully, then please replace the docking station to the proper height. Test by the unit, turn on the power switch of the unit, Use ( ) on APP or press robotic control panel icon to control the robot go back to the docking station for recharging. Please refer to below picture.
INSTALLATION GUIDE Preparation of Room Containment: 1. Turn the power switch off. 2. Press two points mark A and slide the cover in the direction of arrow B as shown in the diagram below. 3. Insert four size AA batteries and match "+"and "-" to the battery compartment, then close the cover of the containment.
GENERAL OPERATION Preparation for Operation: 1. Install the side brushes and install the battery according to the manual. 2. Turn on the power switch on the side of the unit, and charge the battery for 4~6 hours prior to the first operation. 3. To ensure the best efficiency of the unit, first is to remove clothes, paper, cable, extension cable scattered on the floor, roll up the curtains and drapes if any to avert the possible accident.
GENERAL OPERATION Control Panel: Docking LED Indicator Double 8 LED Display Wifi Connection Status ICON Clean Pattern ICON Power Button Dust Bin Full or Nozzle Block LED Indicator Docking Button Small Area Clean Button (Wifi pairing Button) 18
GENERAL OPERATION Download APP and scheduling setting : How to Download APP: 1. To download " SmartCleanerQ " APP from Playstore or APP store. 2. Scan the QR code and download APP. Android iOS Scheduling setting from APP: ※The vacuum cleaner can function normally no matter Wi-Fi is connected or not.
GENERAL OPERATION Basic Operation: →Manual work ※When LED Indicator lights on. → Check: . Dust bin is full. . Intake Valve is stuck with dirt. . Wipe out the inner and outside of Intake Valve area. 1. Turn ON the power switch, wait for power LED light on(green). 2. Press power key. 3. After work is completed, the unit will emit a buzz of warning . The unit stop or back to dock station for charging depends on the settings. 4.
GENERAL OPERATION Table A: Error code on LED Display(Power LED flash Red) Display on screen Possible cause Solution The wheels stuck. Remove M680GMA from obstacles, and Re-start the power switch. The top cover or dust bin is not installed properly. Install the top cover and dust bin properly. The unit will detect the error and fix automatically . The bumper stuck. Remove M680GMA from obstacles. The unit will detect the error and fix automatically . The unit lifted up from the floor.
CLEANING AND MAINTENANCE Maintenance Method: The operation and maintenance of the M680GMA is very simple. After each use, clean any dirt left behind on the dust bin and filter. It is not necessary to clean the intake after every use. Cleaning Dust Bin: 1. Lift up the cover at "A" in the direction as arrow "B" shown in below diagram to remove the Top Cover from the cleaner. B A 2. Pull up the grip and take out the dust bin from the cleaner.
CLEANING AND MAINTENANCE 3. Open the upper cover of the dust bin. Side buckle 4. Lift up and take out the filter. 5. Throw away the dust and dirt from the dust bin.
