User's Manual

Innovation, Science and Economic Development Canada
ISED (English)
This radio transmitter has been approved by ISED to operate with the dipole Pulse W1038. Other antenna types are strictly
prohibited for use with this device.
This device complies with Industry Canada’s license-exempt RSS standards. Operation is subject to the following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Statement
Exception from routine SAR evaluation limits are given in RSS-102 Issue 5. MDF-1019 meets the given requirements when
the minimum separation distance to human body 20 cm. RF exposure or SAR evaluation is not required when the separation distance is
20 cm or more. If the separation distance is less than 20 cm the OEM integrator is responsible for evaluating the SAR.
OEM Responsibilities to comply with ISED Regulations
The MDF-1019 Module has been certified for integration into products only by OEM integrators under the following conditions:
• The antenna(s) must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna)
and all persons at all times.
• The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter.
As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still respon-
sible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.).
Note: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the IC
authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integra-
tor will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization.
End Product Labeling
The MDF-1019 module is labeled with its own IC ID. If the IC ID is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the
final end product must be labeled in a visible area with the following:
"Contains IC: 1156A-MDF1019"
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or
change RF related parameters in the user manual of the end product.
ISED (Français)
Cet émetteur radio (IC : 1156A-MDF1019) a reçu l'approbation d'ISED pour une exploitation avec l'antenne dipole Pulse W1038. Il
est strictement interdit d'utiliser d'autres types d'antenne avec cet appareil.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage; et
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible de provoquer un fonctionnement
non désiré de l’appareil.
Déclaration relative à l'exposition aux radiofréquences (RF)
Les limites applicables à l’exemption de l’évaluation courante du DAS sont énoncées dans le CNR 102, 5e édition. Le module
MDF-1019 répond aux exigences données quand la distance de séparation minimum par rapport au corps humain est de 20 c
m.
L'évaluation de l'exposition aux RF ou du DAS n'est pas requise quand la distance de séparation est de 20 cm ou plus. Si la
distance de séparation est inférieure à 20 cm, il incombe à l'intégrateur FEO d'évaluer le DAS.
Responsabilités du FEO ayant trait à la conformité avec les règlements ISED
Le Module MDF-1019 a été certifié pour une intégration dans des produits uniquement par les intégrateurs FEO dans les con-ditions
suivantes: