Installation Guide

Please leave this sheet and warranty for the customer for future reference
Before installation, remove white plastic quick
connect assembly (1A) from the free end of
pulldown hose.
Step 1
Figure 2a
Step 2a Three Hole Mounting
Screw bolts to the escutcheon. Insert escutcheon
assembly through the base plate and the holes of
the sink.
Screw quick connector to the free end of
pull-down hose. Align block (4A) and tabs (4B)
on quick connector. Push quick connector
housing firmly upward to snap onto receiving
block. Pull down with moderate pressure to
ensure connection has been made. After
connecting the hose, attach weight (4C) onto
the black hose at bottom of the loop to prevent
hose from twisting.
Untie black p
ull-down spray hose and secure
sprayhead onto faucet spout ensuring it clicks
into place. Insert faucet through hole in
escutcheon. From underneath sink, slide plastic
washer (2A), metal washer (2B), and threaded
nut (2C) onto faucet ensuring that you pass both
hot and cold water supply hoses through first
followed by black pull-down spray hose. Secure
by tightening threaded mounting nut (2C).
Step 2b Three Hole Mounting
Step 4
Figure 1
Hole diameters are 1 1/4" minimum to 1 3/4" maximum
Maximum deck thickness is 3 3/16" (without escutcheon) or 2 11/16"
(with escutcheon)
This kitchen faucet comes completely assembled and water tested
Includes braided nylon supply lines with 3/8" Inlets
Tools required-channel lock pliers (or pipe wrench), basin wrench and small crescent wrench
For additional assistance or service call: 1-855-480-2915 or visit our website www.miseno.com
Please leave this sheet and warranty for the customer for future reference
Figure 4Figure 3
Step 3 Single Hole Mounting
Untie black pull-down spray hose and secure
sprayhead onto faucet spout ensuring it clicks
into place. Insert faucet through hole in sink or
countertop. From underneath sink, slide plastic
washer (3A), metal washer (3B), and threaded
nut (3C) onto faucet ensuring that you pass both
hot and cold water supply hoses through first
followed by black pulldown spray hose. Secure
by tightening threaded mounting nut (3C).
Page 1 Page 2
Shut off water supply prior to beginning installation
Parts
RP60089 O-ring
RP70305 Weight
RP60002 O-ring
RP13253* Handle
RP50002 Set Screw
RP80184* Cap
RP70261 Bonnet
MIR20081 Cartridge&Screw
RP64131 Washer
RP64146 Washer
RP56063 Nut
RP80246* Escutcheon
RP80277 Base Plate
RP50071 Bolt
RP56109 Mounting Nut
RP38121* Spray
Head & Hose
Maintenance: Clean with warm water, soft cotton
cloth and non-abrasive liquid dish soap. Towel dry.
Never use acids, harsh abrasives, detergents, or
products containing chlorides on any parts of this
product.
Figure 2b
Figure 6
Step 6
Important: After installation is completed, turn
on hot and cold water supplies. Check for leaks.
Pull the hose assembly out of the spout and
remove the spray head by unscrewing it from
the hose counterclockwise. Be sure to hold the
end of the hose down into the sink and turn the
faucet on to the warm position where it mixes
hot and cold water. Flush water lines for one
minute. Check for leaks. Re-tighten any
connections if necessary, but do not
over tighten. Reinstall spray head by hand
tightening it back onto the spray hose.
1A
2A
2B
2C
3A
3B
3C
4C
Polish Chrome
CP
*Specify
Finish
Finish Codes
SS
Stainless Steel PVD
Button A
Button
B
NOTE: This faucet is equipped with a
two function sprayer plus a Pause
function. Once the faucet turned off it
will automatically revert back to regular
aerated stream.
Button A: Changes flow from regular
stream to full spray
Button B: Changes flow from full
spray to regular stream.
PAUSE: To initiate Pause please press
& hold Button B. Release when you
wish to have water flow begin again.
MNO171A
For additional assistance or service call: 1-855-480-2915 or visit our website www.miseno.com
MNO171A
5B
5A
Making the waterline connections
Thread the nut (5A) on supply line onto outlet
of water supply valve (5B) and tighten with
wrench. Do not over tighten.
Step 5
Figure 5
4A
4B
MIRX70443 Quick Connector