Assembly Instruction

ManualsBrandsMistana ManualsCeiling LightsEmely 3 - Light 16'' Unique/Statement Geometric Flush Mount

1of2

(3)A19MediumBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar Assembly

Diffuser

Glass Panel

x18

Fixture

Body

Cage

STEP 1 - Install Diffuser and Glass Panels

A. Insert the Diffuser (D) in the bottom of the

Cage (C) and secure by folding tabs in the

bottom edge of the Cage (C).

B. E side of the

Install the Glass Panel ( ) into the

Cage ( ) and secure by folding tabs in the top

and bottom of the Cage ( ). Repeat this

process to complete installation of all Glass

Panels ( ).

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

c and Fixture Body (B) Crossbar Assembly (A)

and secure with mounting balls. Note: The should be

snug against the and the mounting balls. If

ceiling canopy

not, adjust the

length of the nipple on the Crossbar Assembly (A) by unscrewing

the preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the ceiling canopy and Fixture Body (B) is secure,

remove the mounting ball and ceiling canopy and Fixture Body (B)

and proceed to Step 4.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

Tab

Figure 1

Assembly Instruction

Summary of content (2 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) A19 Medium Base Bulbs 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 4 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. FINISH: AGED GOLD 13.25” Dia.