Installation & Assembly

ManualsBrandsMistana ManualsBedsTomaszewski Upholstered Low Profile Sleigh Bed

Page 1 of 6

Hardware:

Component:

Bolt M8x60mm x3

Flat Washer x8

Allen Wrench x1

Thank you for purchasing the BED！

Before you start, here is some helpful advice:

1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step

instructions.

2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or

padded area, in the room that it is intended for. Approx assembly time: 45 minutes.

3.Please do not use any tools other than those provided or recommended in these instructions.

4.Please do not throw away any of the packaging or the instruction until you have checked all the components and

hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe

environmentally friendly way.

5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the

components from time to time, so please save the tools that has been provided.

6.Please keep all fitting out of reach of children.

P10

P11

P12

P14

Bolt M8x20mm x28

Bolt M8x35mm x12

Spring Washer x8

Nut M8 x6

Open Wrench x1

Headboard x1

Footboard x1

P1 P2

Side Rail x2

Metal Corner x4

Stretcher x1

Center Rail x2

Leg x2

Short Support Leg x2

P10

Long Support Leg x2

P11

Center Support Leg x1

P12

Plastic Cover x12

P13 P14

Slat x24

P13

BED

Summary of content (6 pages)

PAGE 1
BED Thank you for purchasing the BED！ Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. 2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. Approx assembly time: 45 minutes. 3.Please do not use any tools other than those provided or recommended in these instructions. 4.
PAGE 2
BED STEP 1: Attach 1 piece of Leg (P8) and 1 piece of Leg (P9) into Headboard (P1) as shown. Secure by using 4 pieces of Bolt (B), 4 pieces of Spring Washer (D) and 4 pieces of Flat Washer (E). Use Allen Wrench (G) to tighten Bolts (B) clockwise until secure. Repeat the same steps for Footboard (P2). P1 P9 P8 P2 P1 P8 P8/P9 E D B Bx8 Dx8 Ex8 E D BG P9 Gx1 Hardware & Tool required STEP 2: Attach 2 pieces of Metal Corner (P5) into Headboard (P1). Secure by using 4 pieces of Bolt (A) as shown.
PAGE 3
BED STEP 3: Connect 1 piece of Side Rail (P3) and 1 piece of Side Rail (P4) by using 1 piece of Short Support Leg (P10) as shown. Secure by using 2 pieces of Bolt (A). Use Allen Wrench (G) to tighten Bolts (A) clockwise until secure. Repeat the same steps for the remaining Side Rail (P3&P4) and Short Support Leg (P10). P3 A P4 A G P10 Ax4 Gx1 Hardware & Tool required STEP 4: Attach 1 piece of assembled Side Rail (P3&P4) to Headboard (P1) and Footboard (P2).
PAGE 4
BED STEP 5: Attach 1 piece of Long Support Leg (P11) to 1 piece of Center Rail (P7) as shown. Insert 2 pieces of Bolt (B) through the corresponding holes on Center Rail (P7) to the holes on Long Support Leg (P11). Secure by using 2 pieces of Nut (F). Use Allen Wrench (G) and Open Wrench (H) to tighten Bolts (B) and Nuts (F) until secure. Repeat the same steps for the remaining Center Rail (P7) and Long Support Leg (P11).
PAGE 5
BED STEP 7: Attach Center Support Leg (P11) to each end of Center Rail (P7) as shown. Insert 2 pieces of Bolt (C) from the holes on one side of Center Support Leg (P11) through the corresponding holes on each Center Rail (P7) to the holes on the other side of Center Support Leg (P11). Secure by using 2 pieces of Nut (F). Use Allen Wrench (G) and Open Wrench (H) to tighten Bolts (C) and Nuts (F) until secure.
PAGE 6
BED STEP 9: Insert 1 piece of Bolt (C) through the holes on Stretcher (P6) into the holes on Center Support Leg (P12). Use Allen Wrench (G) to tighten Bolts (C), do not fully tighten Bolts (C) at this step. G C P7 P7 P6 P12 P7 11 P7 P12 Cx1 Gx1 Hardware & Tool required STEP 10: Insert 2 pieces of Slat (P14) into 1 piece of Plastic Cover (P13) as shown. Insert the other end of the same Slats (P14) into the corresponding pre-drilled holes at each Side Rail (P3&P4) as shown.