Technical Specifications

ManualsBrandsMiTek ManualsConstruction Hardware6-3/4" x 6" Steel Glulam Face Mount Hanger

Glulam Beam Connectors

165

GHF Glulam Face Mount Hangers

Specialty Options Chart

– refer to Specialty Options pages 228-229 for additional details

Option

Skewed

1,3

Sloped Seat

Sloped / Skewed

1,2

Inverted Flange

1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.

2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.

3) Skewed hangers typically require a bevel cut however, a square cut option may be available as a custom when requested.

New products or updated product information are designated in

blue font

Allowable

Loads

Ordering

80% of table load

on skews greater.

75% of uplift load than 15˚.

100% of table load.

65% of table load when

nailing into the support

members end grain.

Add SK , angle required,

right (R) or left (L) , and

square cut

(SQ)

bevel cut

(BV)

to product number.

Ex. GHF31900_SK45R_BV

See Sloped Seat and Skewed.

Ex.

GHF31900_SK45R_BV_SL30D

Add IF to product number.

Ex. GHF51135_IF

Add SL, slope required, and

up (U) or down (D),

to product number.

Ex. GHF31900_SL30D

100% of table load

100% of table load.

75% of uplift load on skews

greater than 15˚.

Range

1˚ to 50˚ 1˚ to 45˚ See Sloped Seat and Skewed

Not available in widths

less than 4-1/2"

Glulam Beam Connectors

Typical GHF51135IF

inverted ange

installation

Installation:

• Use all specied fasteners. See Product Notes, page 17.

• WS Wood Screws are supplied with GHF hangers.

Floor

Uplift

Ref. No. W H D Qty Type Qty Type 100% 115% 125% 160%

3-1/8 x 6 GHF31600 -- -- 12 3-3/16 5-7/8 2-3/8 10 WS25 4 WS25 2190 2520 2740 1400

3-1/8 x 7-1/2 GHF31750 -- -- 12 3-3/16 7-3/8 2-3/8 12 WS25 4 WS25 2630 3020 3285 1400

3-1/8 x 9 GHF31900 -- -- 12 3-3/16 8-7/8 2-3/8 16 WS25 5 WS25 3505 4030 4380 1750

3-1/8 x 10-1/2 GHF31105 -- -- 12 3-3/16 10-3/8 2-3/8 20 WS25 6 WS25 4380 5035 5475 2100

3-1/8 x 12 GHF31120 -- -- 12 3-3/16 11-7/8 2-3/8 22 WS25 6 WS25 4820 5540 5800 2100

3-1/8 x 13-1/2 GHF31135 -- -- 12 3-3/16 13-3/8 2-3/4 24 WS25 6 WS25 5255 5665 5800 2100

3-1/8 x 15 GHF31150 -- -- 12 3-3/16 14-7/8 2-3/4 26 WS25 7 WS25 5695 6550 6730 2455

3-1/8 x 16-1/2 GHF31165 -- -- 12 3-3/16 16-3/8 2-3/4 28 WS25 9 WS25 6130 7050 7275 3155

3-1/8 x 18 GHF31178 -- -- 12 3-3/16 17-3/4 2-3/4 30 WS25 11 WS25 6570 7555 7825 3855

3-1/4 x 9 GHF32900 -- -- 12 3-5/16 8-7/8 2-3/8 16 WS25 5 WS25 3505 4030 4380 1750

3-1/4 x 12 GHF32120 -- -- 12 3-5/16 11-7/8 2-3/8 22 WS25 6 WS25 4820 5540 5800 2100

5-1/8 x 6 GHF51600 -- -- 12 5-3/16 5-7/8 2-3/8 10 WS3 4 WS3 2190 2520 2740 1400

5-1/8 x 7-1/2 GHF51750 -- -- 12 5-3/16 7-3/8 2-3/8 14 WS3 4 WS3 3065 3525 3835 1400

5-1/8 x 9 GHF51900 -- -- 12 5-3/16 8-7/8 2-3/8 18 WS3 5 WS3 3940 4535 4930 1750

5-1/8 x 10-1/2 GHF51105 -- -- 12 5-3/16 10-3/8 2-3/8 22 WS3 6 WS3 4820 5540 6025 2100

5-1/8 x 12 GHF51120 -- -- 12 5-3/16 11-7/8 2-3/8 24 WS3 6 WS3 5255 6045 6570 2100

5-1/8 x 13-1/2 GHF51135 -- -- 7 5-3/16 13-3/8 2-3/8 26 WS3 6 WS3 6500 7475 8125 2400

5-1/8 x 15 GHF51150 -- -- 7 5-3/16 14-7/8 2-3/4 28 WS3 7 WS3 7000 8050 8750 2800

5-1/8 x 16-1/2 GHF51165 -- -- 7 5-3/16 16-3/8 2-3/4 30 WS3 7 WS3 7500 8625 9375 2800

5-1/8 x 18 GHF51178 -- -- 7 5-3/16 17-3/4 2-3/4 32 WS3 8 WS3 8000 9200 10000 3200

5-1/8 x 19-1/2 GHF51192 -- -- 7 5-3/16 19-1/8 2-3/4 34 WS3 8 WS3 8500 9775 10395 3200

5-1/8 x 21 GHF51205 -- -- 7 5-3/16 20-3/8 2-3/4 36 WS3 9 WS3 9000 10350 10705 3600

5-1/8 x 24 GHF51233 -- -- 7 5-3/16 23-1/4 2-3/4 40 WS3 11 WS3 10000 11055 11330 4400

1) Allowable loads based on seat bearing calculated at 560 psi perpendicular to grain.

2) WS25 Wood Screws are 1/4" x 2-1/2" long, WS3 Wood Screws are 1/4" x 3" long and are included with GHF hangers.

3) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.

Floor

Uplift

Ref. No. W H D Qty Type Qty Type 100% 115% 125% 160%

5-1/4 x 9 GHF52900 -- -- 12 5-5/16 8-7/8 2-3/8 18 WS3 5 WS3 3940 4535 4930 1750

5-1/4 x 12 GHF52120 -- -- 12 5-5/16 11-7/8 2-3/8 24 WS3 6 WS3 5255 6045 6570 2100

6-3/4 x 6 GHF67600 -- -- 12 6-7/8 5-7/8 2-3/8 12 WS3 4 WS3 2630 3020 3285 1400

6-3/4 x 7-1/2 GHF67750 -- -- 12 6-7/8 7-3/8 2-3/8 16 WS3 5 WS3 3505 4030 4380 1750

6-3/4 x 9 GHF67900 -- -- 12 6-7/8 8-7/8 2-3/8 20 WS3 6 WS3 4380 5035 5475 2100

6-3/4 x 10-1/2 GHF67105 -- -- 12 6-7/8 10-3/8 2-3/8 24 WS3 8 WS3 5255 6045 6570 2805

6-3/4 x 12 GHF67120 -- -- 7 6-7/8 11-7/8 2-3/4 28 WS3 8 WS3 7000 8050 8750 3200

6-3/4 x 13-1/2 GHF67135 -- -- 7 6-7/8 13-3/8 2-3/4 30 WS3 8 WS3 7500 8625 9375 3200

6-3/4 x 15 GHF67150 -- -- 7 6-7/8 14-7/8 2-3/4 32 WS3 10 WS3 8000 9200 10000 4000

6-3/4 x 16-1/2 GHF67165 -- -- 7 6-7/8 16-3/8 2-3/4 34 WS3 10 WS3 8500 9775 10625 4000

6-3/4 x 18 GHF67180 -- -- 7 6-7/8 17-3/4 2-3/4 36 WS3 12 WS3 9000 10350 11250 4800

6-3/4 x 19-1/2 GHF67195 -- -- 7 6-7/8 19-1/8 3 40 WS3 14 WS3 10000 11500 12500 5600

6-3/4 x 21 GHF67210 -- -- 7 6-7/8 20-3/8 3 44 WS3 18 WS3 11000 12650 13000 7200

6-3/4 x 22-1/2 GHF67225 -- -- 7 6-7/8 21-7/8 3 46 WS3 20 WS3 11500 13000 13000 8000

6-3/4 x 24 GHF67240 -- -- 7 6-7/8 23-1/4 3 48 WS3 22 WS3 12000 13000 13000 8800

1) Allowable loads based on seat bearing calculated at 560 psi perpendicular to grain.

2) WS25 Wood Screws are 1/4" x 2-1/2" long, WS3 Wood Screws are 1/4" x 3" long and are included with GHF hangers.

3) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.

Dimensions (in)

130

Glulam

Size

USP

Stock No.

Steel

Gauge

Code

Ref.

Joist

Roof

Fastener Schedule

Header

130

DF/SP

Allowable Loads (Lbs.)