Technical Specifications
110
Hangers
© 2015 MiTek. All rights reserved.
Face Mount Hanger Charts
Floor
Uplift
1
Joist Size Ref. No. W H D A Qty Nail Qty Nail 100% 115% 125% 160%
10 10d 6 10d x 1-1/2 1180 1295 1295 855
10 16d 6 10d x 1-1/2 1400 1600 1740 855
8 10d HDG 4 10d x 1-1/2 HDG 930 1065 1160 730
8 16d HDG 4 10d x 1-1/2 HDG 1105 1215 1215 730
14 10d 8 10d x 1-1/2 1650 1875 1875 1100
14 16d 8 10d x 1-1/2 1960 1965 1965 1100
11 10d HDG 6 10d x 1-1/2 HDG 1275 1465 1595 1095
11 16d HDG 6 10d x 1-1/2 HDG 1520 1745 1900 1095
JUS28 LUS28 18 1-9/16 6-5/8 1-3/4 1 6 10d 4 10d 1110 1270 1375 1115
JUS210 LUS210 18 1-9/16 7-3/4 1-3/4 1 8 10d 4 10d 1350 1545 1670 1115
MUS28 MUS28 18 1-9/16 7-1/16 2 1 8 10d 8 10d 1710 1970 2140 1230 31, F32
8 10d 6 10d x 1-1/2 1000 1120 1210 800
8 16d 6 10d x 1-1/2 1175 1335 1440 800
10 10d 6 10d x 1-1/2 1250 1405 1515 1135
10 16d 6 10d x 1-1/2 1470 1670 1800 1135
HUS28 HUS28 16 1-5/8 7-3/16 3 2 22 16d 8 16d 4170 4345 4345 2570
HUS210 HUS210 16 1-5/8 9-3/16 3 2 30 16d 10 16d 5455 5510 5510 3205
HD210 HU210 14 1-9/16 7-3/16 2 1-1/8 12 16d 4 10d x 1-1/2 1690 1945 2115 730
14 10d 8 10d x 1-1/2 1650 1875 1875 1100
14 16d 8 10d x 1-1/2 1960 1965 1965 1100
11 10d HDG 6 10d x 1-1/2 HDG 1275 1465 1595 1095
11 16d HDG 6 10d x 1-1/2 HDG 1520 1745 1900 1095
JUS210 LUS210 18 1-9/16 7-3/4 1-3/4 1 8 10d 4 10d 1350 1545 1670 1115
10 10d 6 10d x 1-1/2 1250 1405 1515 1135
10 16d 6 10d x 1-1/2 1470 1670 1800 1135
HUS210 HUS210 16 1-5/8 9-3/16 3 2 30 16d 10 16d 5455 5510 5510 3205
HD210 HU210 14 1-9/16 7-3/16 2 1-1/8 12 16d 4 10d x 1-1/2 1690 1945 2115 730
HD212 HU212 14 1-9/16 9-1/4 2 1-1/8 16 16d 6 10d x 1-1/2 2255 2595 2730 1065
HD212IF HUC212 14 1-9/16 9-1/4 2 -- -- 16 16d 6 10d x 1-1/2 2255 2595 2730 1065
12 10d 8 10d x 1-1/2 1500 1685 1815 1330
12 16d 8 10d x 1-1/2 1765 2000 2160 1330
HD212 HU212 14 1-9/16 9-1/4 2 1-1/8 16 16d 6 10d x 1-1/2 2255 2595 2730 1065
HD212IF HUC212 14 1-9/16 9-1/4 2 -- -- 16 16d 6 10d x 1-1/2 2255 2595 2730 1065
HD214 HU214 14 1-9/16 11-1/2 2 1-1/8 20 16d 6 10d x 1-1/2 2560 2660 2730 1065
12 10d 8 10d x 1-1/2 1500 1685 1815 1330
12 16d 8 10d x 1-1/2 1765 2000 2160 1330
HD212 HU212 14 1-9/16 9-1/4 2 1-1/8 16 16d 6 10d x 1-1/2 2255 2595 2730 1065
HD212IF HUC212 14 1-9/16 9-1/4 2 -- -- 16 16d 6 10d x 1-1/2 2255 2595 2730 1065
HD214 HU214 14 1-9/16 11-1/2 2 1-1/8 20 16d 6 10d x 1-1/2 2560 2660 2730 1065
HD216 HU216 14 1-9/16 13-1/2 2 1-1/8 24 16d 8 10d x 1-1/2 2785 2925 3015 1065
JUS24-2 LUS24-2 18 3-1/8 3-7/16 2 1 4 16d 2 16d 805 920 965 325
6 10d 2 10d 750 840 910 380
6 16d 2 10d 880 1000 1080 380
HD24-2 HU24-2 14 3-1/8 3-1/2 2-1/2 1-1/8 4 16d 2 10d 565 650 705 320
HUS24-2 -- -- 14 3-1/8 3-7/16 2 1 4 16d 2 16d 850 965 1040 495
HUS24-2IF -- -- 14 3-1/8 3-7/16 2 1 4 16d 2 16d 850 965 1040 495
JUS26-2 LUS26-2 18 3-1/8 5-1/4 2 1 4 16d 4 16d 1040 1185 1220 1355
10 10d 4 10d 1250 1405 1515 755
10 16d 4 10d 1470 1670 1800 755
HD24-2 HU24-2 14 3-1/8 3-1/2 2-1/2 1-1/8 4 16d 2 10d 565 650 705 320
HUS26-2 HUS26-2 14 3-1/8 5-1/4 2 1 4 16d 4 16d 1085 1235 1300 1155
HUS26-2IF HUSC26-2 14 3-1/8 5-1/4 2 1 4 16d 4 16d 1085 1235 1300 1155
HD26-2 HU26-2 14 3-1/8 5-1/8 2-1/2 1-1/8 12 16d 6 10d 1690 1945 2095 1140
HD26-2IF HUC26-2 14 3-1/8 5-1/8 2-1/2 1-1/8 12 16d 6 10d 1690 1945 2095 1140
1
)
U
p
lift loads have been increased 60% for wind or seismic loads; no further increase shall be
p
ermitted.
2
)
Minimum nail embedment shall be 1-1/2" for 10d nails and 1-5/8" for 16d nails.
3
)
16d sinkers
(
0.148 dia. x 3-1/4" lon
g)
ma
y
be used at 0.84 of the table load where 16d commons are s
p
ecified. This does not a
pp
l
y
to JUS, HUS, MUS slant nail han
g
ers.
4
)
For JUS, HUS, and MUS han
g
ers: Nails must be driven at a 30° to 45˚ an
g
le throu
g
h the
j
oist or truss into the header to achieve the table loads.
5
)
NAILS: 10d x 1-1/2" nails are 0.148" dia. x 1-1/2" lon
g,
10d nails are 0.148" dia. x 3" lon
g,
16d nails are 0.162" dia. x 3-1/2" lon
g
.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
(2) 2 x 6
SUH26-2 1-1/8 U26-2 16 3-1/8 5-1/16 2
5,
R5,
F2
(2) 2 x 4
SUH24-2 U24-2 1-1/816 3-1/8 3-1/8 2
2 x 16
SUH214 U214
2 x 14
SUH214 U214
16 1-9/16 10 2
16
15/16
16 1-9/16 2 1-3/168
82
1-9/16 10 2 1-1/8
1-1/8
2 x 12
JL210 LU210
2 x 10
JL28 LU28
JL28IF-TZ -- --
JL210 LU210
SUH28 -- --
SUH210 U210
JL210IF-TZ LUC210Z
20 1-9/16
15/16
-- --
8-1/4
31, F32
5, R5,
F2
18 1-9/16 -- --
6-3/8
5,
R5,
F2
20 5, R5, F2
31,
F32
5, R5,
F2
18 1-9/16 8-1/4 1-1/2 -- --
16 1-9/16 6-5/8 2 1-3/16
1-9/16 8-1/4 1-1/2
Code
Ref.
31, F32
Corrosion
Finish
Fastener Schedule
2,3,5
Header Joist
DF/SP
Allowable Loads (Lbs.)
4
Dimensions (in)
USP
Stock No.
Steel
Gauge
Roof
1-3/16
1-1/2
18 1-9/16 8-1/4 1-1/2
16 1-9/16
1-1/2 15/16
20 1-9/16
6-1/8 1-1/2
JL210IF-TZ LUC210Z
SUH210 U210
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Continued on next page
Hangers
A
D
H
W