Technical Specifications

115
Hangers
© 2015 MiTek. All rights reserved.
Face Mount Hanger Charts
Floor
Uplift
1
Joist Size Ref. No. W H D A Qty Nail Qty Nail 100% 115% 125% 160%
JUS414 LUS414 18 3-5/8 12-7/8 2 1 12 16d 6 16d 2420 2755 2995 1980
18 10d 6 10d 2250 2525 2725 1135
18 16d 6 10d 2645 3000 3010 1135
HD410 HU410 14 3-9/16 8-13/16 2-1/2 1-1/8 18 16d 10 10d 2540 2920 3175 1905
HD410IF HUC410 14 3-9/16 8-13/16 2-1/2 -- -- 18 16d 10 10d 2540 2920 3175 1905
HDQ410IF HUCQ410 14 3-9/16 9 3 1-1/2 12 WS3 6 WS3 5015 5590 5590 2975 31, F32
HUS412 HUS412 14 3-5/8 10-7/8 2 1 10 16d 10 16d 2710 3080 3325 3060
HUS412IF HUSC412 14 3-5/8 10-7/8 2 1 10 16d 10 16d 2710 3080 3325 3060
HDQ412IF HUCQ412 14 3-9/16 11 3 1-1/2 14 WS3 6 WS3 5605 5605 5605 3280 31, F32
HD412 HU412 14 3-9/16 10-13/16 2-1/2 1-1/8 22 16d 10 10d 3100 3565 3880 1905
HD412IF HUC412 14 3-9/16 10-13/16 2-1/2 -- -- 22 16d 10 10d 3100 3565 3880 1905
HD414 HU414 14 3-9/16 12-13/16 2-1/2 1-1/8 24 16d 10 10d 3385 3890 4230 1905
HD414IF HUC414 14 3-9/16 12-13/16 2-1/2 -- -- 24 16d 10 10d 3385 3890 4230 1905
JUS414 LUS414 18 3-5/8 12-7/8 2 1 12 16d 6 16d 2420 2755 2995 1980
18 10d 6 10d 2250 2525 2725 1135
18 16d 6 10d 2645 3000 3010 1135
HD412 HU412 14 3-9/16 10-13/16 2-1/2 1-1/8 22 16d 10 10d 3100 3565 3880 1905
HD412IF HUC412 14 3-9/16 10-13/16 2-1/2 -- -- 22 16d 10 10d 3100 3565 3880 1905
HDQ412IF HUCQ412 14 3-9/16 11 3 1-1/2 14 WS3 6 WS3 5605 5605 5605 3280 31, F32
HD414 HU414 14 3-9/16 12-13/16 2-1/2 1-1/8 24 16d 10 10d 3385 3890 4230 1905
HD414IF HUC414 14 3-9/16 12-13/16 2-1/2 -- -- 24 16d 10 10d 3385 3890 4230 1905
HD416 HU416 14 3-9/16 14-13/16 2-1/2 1-1/8 26 16d 12 10d 3665 4215 4570 2285
HD416IF HUC416 14 3-9/16 14-13/16 2-1/2 -- -- 26 16d 12 10d 3665 4215 4570 2285
HD414 HU414 14 3-9/16 12-13/16 2-1/2 1-1/8 24 16d 10 10d 3385 3890 4230 1905
HD414IF HUC414 14 3-9/16 12-13/16 2-1/2 -- -- 24 16d 10 10d 3385 3890 4230 1905
HD416 HU416 14 3-9/16 14-13/16 2-1/2 1-1/8 26 16d 12 10d 3665 4215 4570 2285
HD416IF HUC416 14 3-9/16 14-13/16 2-1/2 -- -- 26 16d 12 10d 3665 4215 4570 2285
HD418 -- -- 14 3-9/16 16-1/2 2-1/2 1-1/4 28 16d 8 10d 3950 4540 4570 1425
8 10d 4 10d 1000 1120 1210 755
8 16d 4 10d 1175 1335 1440 755
HD66 HU66 14 5-1/2 3-15/16 2-1/2 1-1/8 12 16d 6 10d 1690 1945 2095 1140
HD66IF HUC66 14 5-1/2 3-15/16 2-1/2 -- -- 12 16d 6 10d 1690 1945 2095 1140
8 10d 4 10d 1000 1120 1210 755
8 16d 4 10d 1175 1335 1440 755
HD66 HU66 14 5-1/2 3-15/16 2-1/2 1-1/8 12 16d 6 10d 1690 1945 2095 1140
HD66IF HUC66 14 5-1/2 3-15/16 2-1/2 -- -- 12 16d 6 10d 1690 1945 2095 1140
HD68 HU68 14 5-1/2 5-15/16 2-1/2 1-1/8 14 16d 6 10d 1975 2270 2470 1140
HD68IF HUC68 14 5-1/2 5-15/16 2-1/2 -- -- 14 16d 6 10d 1975 2270 2470 1140
14 10d 6 10d 1750 1965 2120 1135
14 16d 6 10d 2060 2335 2520 1135
HD68 HU68 14 5-1/2 5-15/16 2-1/2 1-1/8 14 16d 6 10d 1975 2270 2470 1140
HD68IF HUC68 14 5-1/2 5-15/16 2-1/2 -- -- 14 16d 6 10d 1975 2270 2470 1140
HD610 HU610 14 5-1/2 7-13/16 2-1/2 1-1/8 18 16d 10 10d 2540 2920 3175 1905
HD610IF HUC610 14 5-1/2 7-13/16 2-1/2 -- -- 18 16d 10 10d 2540 2920 3175 1905
HDQ610IF HUCQ610 14 5-1/2 9 3 1-1/8 12 WS3 6 WS3 5015 5590 5590 2975 31, F32
14 10d 6 10d 1750 1965 2120 1135
14 16d 6 10d 2060 2335 2520 1135
HD610 HU610 14 5-1/2 7-13/16 2-1/2 1-1/8 18 16d 10 10d 2540 2920 3175 1905
HD610IF HUC610 14 5-1/2 7-13/16 2-1/2 -- -- 18 16d 10 10d 2540 2920 3175 1905
HDQ610IF HUCQ610 14 5-1/2 9 3 1-1/2 12 WS3 6 WS3 5015 5590 5590 2975 31, F32
HD612 HU612 14 5-1/2 9-13/16 2-1/2 1-1/8 22 16d 10 10d 3100 3565 3880 1905
HD612IF HUC612 14 5-1/2 9-13/16 2-1/2 -- -- 22 16d 10 10d 3100 3565 3880 1905
HDQ612IF HUCQ612 14 5-1/2 11 3 1-1/2 14 WS3 6 WS3 5605 5605 5605 3280 31, F32
1
)
U
p
lift loads have been increased 60% for wind or seismic loads; no further increase shall be
p
ermitted.
2
)
Minimum nail embedment shall be 1-1/2" for 10d nails and 1-5/8" for 16d nails.
3
)
16d sinkers
(
0.148 dia. x 3-1/4" lon
g)
ma
y
be used at 0.84 of the table load where 16d commons are s
p
ecified. This does not a
pp
l
y
to JUS, HUS, MUS slant nail han
g
ers.
4
)
WS3 Wood Screws are 1/4" x 3" lon
g
and are included with HDQ han
g
ers.
5
)
NAILS: 10d nails are 0.148" dia. x 3" lon
g,
16d nails are 0.162" dia. x 3-1/2" lon
g
.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
5, R5,
F2
5,
R5,
F2
1-1/8
Dimensions (in)
Fastener Schedule
2,3,4,5
DF/SP
Allowable Loads (Lbs.)
4
Corrosion Finish
Header Joist
USP
Stock No.
Steel
Gauge
Roof
Code
Ref.
5,
R5,
F2
1-1/8
5-1/2 5 2
4 x 14
SUH414 U414 16 3-9/16 10-1/16 2
SUH414 U414 16 3-9/16 10-1/16 2
4 x 16
5,
R5,
F2
21
1
6 x 8
SUH66 U66 16 5-1/2 5
4 x 18
6 x 6
SUH66 U66 16
1
6 x 10
SUH610
5,
R5,
F2
U610 16 5-1/2 9 2
5, R5,
F2
1 5,
R5,
F2
6 x 12
SUH610 U610 16 5-1/2 9 2
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Continued on next page
Hangers
A
D
H
W