Technical Specifications

ManualsBrandsMiTek ManualsConstruction Hardware2" x 14-16" Steel Triple Face Mount Hanger

108

Hangers

Heavy-Duty Face Mount Hangers

HD hangers are heavy-duty face mount

hangers that can be used to support headers,

joists, and trusses.

Materials: 14 gauge

Finish: G90 galvanizing

Options: See chart for Corrosion Finish

Options. All nominal lumber sizes are

available rough/full size lumber. See

Specialty Options Chart.

Codes: See page 11 for Code Reference Chart

Installation:

• Use all specied fasteners. See Product

Notes, page 17.

• Some HD models feature nail holes along

bend line that must be lled to achieve

allowable loads. Verify proper header width

to accomplish this for inverted models.

Option

Skewed

1,3

Sloped Seat

2,3

Sloped / Skewed

1,2,3

Inverted Flange

1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.

2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.

3) For skewed hangers, the required cut type (square or bevel) of joist member may vary based on skew angle

and width of hanger. Some square cut hangers will require custom pricing due to welded back plate.

4) HD option hangers may be manufactured as welded products to achieve listed loads. Welded products have a primer finish.

New products or updated product information are designated in

blue font

Range

Allowable

Loads

See Sloped Seat and

Skewed

100% of table load.

75% of uplift load on

skews greater than 15˚.

100% of table load.

65% of table load when

nailing into the support

members end grain.

1˚ to 67-1/2˚

when width is 1-3/4" or less.

1˚ to 50˚ on all others.

Not available in

widths less than 2-1/4"

100% of table load

1˚ to 45˚

80% of table load.

75% of uplift load on

skews greater than 15˚.

Ordering

Add IF,

to product number.

Example: HD410_IF

Add SK, angle required,

right (R) or left (L), and

square cut

(SQ)

or bevel cut

(BV)

to product number.

Example: HD410_SK45R_SQ

Add SL, slope required,

and up (U) or down (D),

to product number.

Example: HD410_SL30D

See Sloped Seat

and Skewed

Example:

HD410_SK45R_SQ_SL30D

HD610 Typical HD bend line

nail installation

Typical HD3212

glulam installation

Typical HDQIF

installation

Typical HD210-2IF

inverted ange installation

HDQIF

HD51135

Typical HD610

installation

Typical HD210-2

installation

Specialty Options Chart

Refer to Specialty Options pages 228-229 for additional details.

Drive bend

line nails

into header at

45° to achieve

listed loads.

HDQIF inverted ange hangers install with wood screws eliminating

the need to drill bolt holes simplifying installation.

Materials: 14 gauge

Finish: G90 galvanizing

Options: See chart for Corrosion Finish Options

Codes: See page 11 for Code Reference Chart

Installation:

• Use all specied fasteners. See Product Notes, page 17.

• WS15 and WS3 Wood Screws are supplied with HDQIF hangers.

HDQIF Inverted Flange Face Mount Hangers

Hangers

Summary of content (13 pages)

PAGE 1
Hangers HD Heavy-Duty Face Mount Hangers HD hangers are heavy-duty face mount hangers that can be used to support headers, joists, and trusses. Materials: 14 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options. All nominal lumber sizes are available rough/full size lumber. See Specialty Options Chart. Codes: See page 11 for Code Reference Chart Typical HD610 installation Typical HD210-2 installation A Installation: • Use all specified fasteners. See Product Notes, page 17.
PAGE 2
Hangers Fastener Schedule2,3,5 Header Joist Dimensions (in) Joist Size USP Stock No. JL24 JL24IF-TZ 2x4 2x6 2x8 Floor Steel Ref. No.
PAGE 3
Hangers Fastener Schedule2,3,5 Header Joist Dimensions (in) Joist Size USP Stock No.
PAGE 4
Hangers Fastener Schedule2,3,5,6 Header Joist Dimensions (in) Joist Size USP Stock No. JUS26-2 JUS28-2 Ref. No.
PAGE 5
Hangers Fastener Schedule2,3,4,5 Header Joist Dimensions (in) Joist Size (2) 2 x 16 3x4 3x6 3x8 3 x 10 3 x 14 Steel Ref. No.
PAGE 6
Hangers Fastener Schedule2,3,4,5 Header Joist Dimensions (in) Joist Size (2) 3 x 8 (2) 3 x 10 (2) 3 x 12 (2) 3 x 14 (3) 2 x 6 (3) 2 x 8 (3) 2 x 10 Ref. No.
PAGE 7
Hangers Fastener Schedule2,3,4,5 Header Joist Dimensions (in) Joist Size 4x4 4x6 4x8 4 x 12 Ref. No.
PAGE 8
Hangers Fastener Schedule2,3,4,5 Header Joist Dimensions (in) Joist Size 4 x 14 4 x 16 4 x 18 6x6 6 x 10 6 x 12 Ref. No.
PAGE 9
Hangers Fastener Schedule2,3,4 Header Joist Dimensions (in) USP Stock No.
PAGE 10
EWP Hangers HD / HDQIF Face Mount Hangers HD – Designed to support LVL, LSL, and PSL beams and headers in medium load conditions. HDQIF – inverted flange face mount hangers fasten to LVL, LSL and PSL beams and headers with WS Wood Screws. Ma terials: See EWP Face Mount Hangers charts, pages 146-148. Finish: G90 galvanizing Options: See Specialty Options chart. Codes: See page 11 for Code Reference Chart Typical HDQIF installation Typical HD installation Installation: • Use all specified fasteners.
PAGE 11
EWP Hangers I-Joist Charts Face Mount Hangers Fastener Schedule2,3 Header Joist Dimensions (in) Joist Size 2-1/2 x 14 2-1/2 x 16 THF25160 2-1/2 x 18 - 24 THF25160 2-5/8 x 9-1/4 - 9-1/2 2-5/8 x 11-1/4 - 11-7/8 2-5/8 x 14 2-5/8 x 16 3 x 9-1/4 - 14 3 x 11-1/4 - 14 3 x 14 3-1/4 x 9-1/4 - 14 3-1/4 x 11-1/4 - 14 3-1/4 x 14 3-1/2 x 9-1/4 - 9-1/2 3-1/2 x 11-1/4 3-1/2 x 14 3-1/2 x 16 - 22 3-1/2 x 16 3-1/2 x 18 - 26 4 - 4-3/16 x 9-1/2 4 - 4-3/16 x 11-7/8 4 - 4-3/16 x 14 Ref. No.
PAGE 12
EWP Hangers SCL Charts Face Mount Hangers Fastener Schedule2,3,4 Dimensions (in) Header Joist Size 1-3/4 x 7-1/4 1-3/4 x 9-1/2 1-3/4 x 11-1/4 - 11-7/8 USP Stock No. HD1770 2-11/16 x 14 - 16 3-1/2 x 9-1/4 - 14 Uplift1 Uplift1 Web Stiff Reqd x Ga 14 W 1-13/16 H 7-1/8 D 2 Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160% 14 16d 4 10d x 1-1/2 1975 2270 2335 760 1695 1950 1960 660 Code Ref.
PAGE 13
EWP Hangers SCL Charts Face Mount Hangers Fastener Schedule2,3,4 Header Joist Dimensions (in) 3-1/2 x 16 - 22 USP Stock No.