Technical Specifications
143
© 2015 MiTek. All rights reserved.
EWP Hangers
HD / HDQIF Face Mount Hangers
HD – Designed to support LVL, LSL, and PSL beams
and headers in medium load conditions.
HDQIF – inverted ange face mount hangers fasten to LVL,
LSL and PSL beams and headers with WS Wood Screws.
Ma terials: See EWP Face Mount Hangers charts,
pages 146-148.
Finish: G90 galvanizing
Options: See Specialty Options chart.
Codes: See page 11 for Code Reference Chart
Installation:
• Use all specied fasteners. See Product Notes,
page 17.
• HD – Drive bend line nails into header at
45° to achieve listed loads.
• WS15 and WS3 Wood Screws are supplied
with HDQIF hangers.
Designed for medium load conditions. Extended
3" deep seat provides extra truss bearing.
Materials: 16 gauge
Finish: G90 galvanizing
Codes: See page 11 for Code Reference Chart
Installation:
• Use all specied fasteners. See Product Notes,
page 17.
• Joist nails must be driven at a 30° to 45° angle
through the joist into the header to achieve
listed loads. Standard length “double shear”
nails must be used to achieve listed load values.
Option
Skewed
1,3
Sloped Seat
2,3
Sloped / Skewed
1,2,3
Inverted Flange
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) For skewed hangers, the required cut type (square or bevel) of joist member may vary based on skew angle
and width of hanger. Some square cut hangers will require custom pricing due to welded back plate.
4) HD option hangers may be manufactured as welded products to achieve listed loads. Welded products have a primer finish.
New products or updated product information are designated in
blue font
.
Range
Allowable
Loads
See Sloped Seat and Skewed
100% of table load.
75% of uplift load on
skews greater than 15˚.
100% of table load.
65% of table load when
nailing into the support
members end grain.
1˚ to 67-1/2˚
when width is 1-3/4" or less.
1˚ to 50˚ on all others.
Not available in
widths less than 2-1/4"
100% of table load
1˚ to 45˚
80% of table load.
75% of uplift load on
skews greater than 15˚.
Ordering
Add IF,
to product number.
Example: HD410_IF
Add SK, angle required,
right (R) or left (L), and
square cut
(SQ) or
bevel cut
(BV)
to product number.
Example: HD410_SK45R_SQ
Add SL, slope required,
and up (U) or down (D),
to product number.
Example: HD410_SL30D
See Sloped Seat and Skewed
Example:
HD410_SK45R_SQ_SL30D
Typical HD bend line
nail installation
HDQIF
Typical HUS
installation
Typical HDQIF
installation
Typical HUS double
shear installation
Typical HD
installation
HD
HUS
HD Specialty Options Chart
– refer to Specialty Options pages 228-229 for additional details.
Drive bend line nails
into header at 45° to
achieve listed loads.
Drive joist nails into header at
30° to 45° to
achieve listed loads.
HUS Face Mount Hangers
H
3"
W
W
D
2"
H
W
3"
Raised dimple
allows 30° to 40°
nailing
EWP Hangers
H