Technical Specifications

125
Hangers
© 2015 MiTek. All rights reserved.
LSSH Slope/Skew Hangers
Floor
Uplift
1
Floor
Uplift
1
Ref. No. W1 W2 Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
1-1/2 LSSH15-TZ
LSU26, LSU26Z,
LSSU28, LSSU28Z
18 1-9/16 1-3/4 6 10d HDG 7 10d x 1-1/2 HDG 685 785 855 740 590 675 735 625 130
1-1/2 LSSH210 LSSU210 18 1-9/16 1-3/4 10 10d 7 10d x 1-1/2 1180 1345 1450 1065 980 1125 1225 895
1-3/4 LSSH179 LSSUI25 18 1-13/16 1-5/8 10 10d 7 10d x 1-1/2 1180 1345 1450 1065 980 1125 1225 895
2 - 2-1/8 LSSH20
LSSUI2.06,
LSSU2.1
18 2-1/8 2-1/2 10 10d 7 10d x 1-1/2 1180 1345 1450 980 980 1125 1225 825
2-1/4 - 2-5/16 LSSH23 LSSUI35 18 2-5/16 2-3/8 10 10d 7 10d x 1-1/2 1180 1345 1450 980 980 1125 1225 825
2-1/2 LSSH25 LSSUH310 16 2-9/16 2-3/4 18 16d 12 10d x 1-1/2 2590 2600 2600 1195 2140 2185 2185 1005
2-5/8 LSSH26 -- -- 16 2-11/16 2-5/8 18 16d 12 10d x 1-1/2 2590 2600 2600 1195 2140 2185 2185 1005
3 LSSH31 LSSU210-2 16 3-1/8 3-3/4 18 16d 12 10d x 1-1/2 2590 2940 3175 1585 2140 2465 2680 1330
3-1/2 LSSH35 LSSU410 16 3-9/16 3-1/2 18 16d 12 10d x 1-1/2 2590 2940 3175 1585 2140 2465 2680 1330
1-1/2 LSSH15-TZ
LSU26, LSU26Z,
LSSU28, LSSU28Z
18 1-9/16 1-3/4 6 10d HDG 7 10d x 1-1/2 HDG 685 785 815 740 590 675 685 625 130
1-1/2 LSSH210 LSSU210 18 1-9/16 1-3/4 10 10d 7 10d x 1-1/2 1180 1345 1450 1065 980 1125 1225 895
1-3/4 LSSH179 LSSUI25 18 1-13/16 1-5/8 10 10d 7 10d x 1-1/2 1180 1345 1450 1065 980 1125 1225 895
2 - 2-1/8 LSSH20
LSSUI2.06,
LSSU2.1
18 2-1/8 2-1/2 10 10d 7 10d x 1-1/2 1180 1345 1450 980 980 1125 1225 825
2-1/4 - 2-5/16 LSSH23 LSSUI35 18 2-5/16 2-3/8 10 10d 7 10d x 1-1/2 1180 1345 1450 980 980 1125 1225 825
2-1/2 LSSH25 LSSUH310 16 2-9/16 2-3/4 14 16d 12 10d x 1-1/2 1825 1825 1825 1195 1530 1530 1530 1005
2-5/8 LSSH26 -- -- 16 2-11/16 2-5/8 14 16d 12 10d x 1-1/2 1825 1825 1825 1195 1530 1530 1530 1005
3 LSSH31 LSSU210-2 16 3-1/8 3-3/4 14 16d 12 10d x 1-1/2 1920 1920 1920 1585 1615 1615 1615 1330
3-1/2 LSSH35 LSSU410 16 3-9/16 3-1/2 14 16d 12 10d x 1-1/2 1920 1920 1920 1585 1615 1615 1615 1330
1
)
U
p
lift loads have been increased 60% for wind or seismic loads; no further increase shall be
p
ermitted.
2
)
Minimum nail
p
enetration shall be 1-1/2"for 10d nails and 1-5/8"for 16d nails.
3
)
NAILS: 10d x 1-1/2"nails are 0.148"dia. x 1-1/2"lon
g,
10d nails are 0.148"dia. x 3"lon
g,
16d nails are 0.162"dia. x 3-1/2"lon
g
.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
Dimensions (in)
Code
Ref.
6,
R11,
F3
6,
R11,
F3
SLOPED ONLY HANGER
S
SKEWED HANGERS or SLOPED & SKEWED HANGERS
USP
Stock No.
Steel
Gauge
Roof Roof
Corrosion Finish
Fastener Schedule
2,3
Header Rafter
DF/SP
Allowable Loads (Lbs.)
S-P-F
Allowable Loads (Lbs.)
Rafter
Width (in)
SKH26R
right skew
SKH26L
left skew
SKH – Standard 45° skew hanger allows for a 40° to 50° skew
range, without hanger modication.
SKHH – For heavier applications.
Materials: 14 or 16 gauge
Finish: G90 galvanizing
Options: See chart for Corrosion Finish Options
Codes: See page 11 for Code Reference Chart
Installation:
• Use all specied fasteners. See Product Notes, page 17.
• The hangers listed are for standard sizes and will accommodate
a 40° to 50° skew range.
• Most sizes do not require a miter cut for installation. Refer to chart
footnote identied with an asterisk.
• Illustrations show left and right skews. (SKH_L = skewed left;
SKH_R = skewed right)
• For I-Joist installations, web stiffeners are required.
• Refer to illustration for staggered I-Joist application for double 2",
2-5/16", and 2-1/2" models.
• For double I-Joist installations, web stiffeners between I-Joists are required.
SKH / SKHH Skewed 45° Hangers
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Continued on next page
SKH210L
SKH210R
W
W
H
D
D
Left skew
Drive nails at angle
Right skew
H
Hangers