Technical Specifications

ManualsBrandsMiTek ManualsConstruction Hardware7" x 16" Steel Masonry Hanger

134

Hangers

MPH Masonry Hangers

These hangers are designed to support standard lumber

joists, I-Joists, or beams. Easy installation into concrete

block walls makes the MPH an attractive alternative to

fabricating seats in masonry (or attaching ledgers) to

support joists or beams.

Materials: 12 gauge

Finish: USP primer

Options: All nominal lumber sizes are available for rough

full size lumber. See Specialty Options Chart on page 135.

Codes: See page 11 for Code Reference Chart

Installation:

• Use all specied fasteners. See Product Notes, page 17.

• 16d duplex nails are not supplied with MPH hangers.

• Place hanger into position on top of concrete block.

Install (2) 16d duplex nails (0.162" dia. x 3-1⁄2" double

head) through the top ange nail holes. Then continue

laying the next course of block.

• A minimum of one course shall be laid over hanger top

ange and one course below hanger top ange. Courses

adjacent to the top ange shall be subsequently grouted.

• These products do not provide uplift resistance.

Typical MPH

single ply installation

Typical MPH

double ply installation

Install with (2) 16d duplex

nails in grouted cell

Install with (2) 16d duplex

nails in grouted cells

Floor

Ref. No. W H L Qty Type Qty Type 100% 115% 125%

2 x 10 MPH210 WM210 12 1-9/16 9-1/4 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

2 x 12 MPH212 WM212 12 1-9/16 11-1/4 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

2 x 14 MPH214 WM214 12 1-9/16 13-1/8 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

2 x 16 MPH216 WM216 12 1-9/16 15-1/8 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

(2) 2 x 10 MPH210-2 WM210-2 12 3-1/8 9-1/4 7 2 16d duplex 2 10d 4280 4280 4280

(2) 2 x 12 MPH212-2 WM212-2 12 3-1/8 11-1/4 7 2 16d duplex 2 10d 4280 4280 4280

(2) 2 x 14 MPH214-2 WM214-2 12 3-1/8 13-1/8 7 2 16d duplex 2 10d 4280 4280 4280

(2) 2 x 16 MPH216-2 WM216-2 12 3-1/8 15-1/8 7 2 16d duplex 2 10d 4280 4280 4280

3 x 10 MPH310 WM310 12 2-9/16 9-1/4 7 2 16d duplex 2 10d x 1-1/2 3240 3240 3240

3 x 12 MPH312 WM312 12 2-9/16 11-1/4 7 2 16d duplex 2 10d x 1-1/2 3240 3240 3240

3 x 14 MPH314 WM314 12 2-9/16 13-1/8 7 2 16d duplex 2 10d x 1-1/2 3240 3240 3240

3 x 16 MPH316 WM316 12 2-9/16 15-1/8 7 2 16d duplex 2 10d x 1-1/2 3240 3240 3240

4 x 10 MPH410 WM410 12 3-9/16 9-1/4 7 2 16d duplex 2 10d 4280 4280 4280

4 x 12 MPH412 WM412 12 3-9/16 11-1/4 7 2 16d duplex 2 10d 4280 4280 4280

4 x 14 MPH414 WM414 12 3-9/16 13-1/8 7 2 16d duplex 2 10d 4280 4280 4280

4 x 16 MPH416 WM416 12 3-9/16 15-1/8 7 2 16d duplex 2 10d 4280 4280 4280

6 x 10 MPH610 WM610 12 5-9/16 9-1/4 7 2 16d duplex 2 10d 4280 4280 4280

1-1/2 x 9-1/4 MPH210 WM29.25 12 1-9/16 9-1/4 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

1-1/2 x 11-1/4 MPH212 WM211.25 12 1-9/16 11-1/4 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

1-1/2 x 9-1/2 MPH1595 WM29.5 12 1-9/16 9-1/2 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

1-1/2 x 11-7/8 MPH15118 WM211.88 12 1-9/16 11-7/8 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

1-1/2 x 14 MPH1514 -- -- 12 1-9/16 14 7 2 16d duplex 2 10d x 1-1/2 2585 2620 2645

1-3/4 x 9-1/2 MPH1795 WM9 12 1-13/16 9-1/2 7 2 16d duplex 2 10d x 1-1/2 2975 3010 3035

1-3/4 x 11-7/8 MPH17118 WM11 12 1-13/16 11-7/8 7 2 16d duplex 2 10d x 1-1/2 2975 3010 3035

1-3/4 x 14 MPH1714 WM14 12 1-13/16 14 7 2 16d duplex 2 10d x 1-1/2 2975 3010 3035

1-3/4 x 16 MPH1716 WM16 12 1-13/16 16 7 2 16d duplex 2 10d x 1-1/2 2975 3010 3035

)

Masonr

com

ressive stren

th shall be minimum 1500

si.

)

NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" lon

10d nails are 0.148" dia. x 3" lon

16d du

lex nails are 0.162" dia. x 3-1/2" lon

double headed nails and shall be installed in

routed cells in accordance to manufacturer's installation s

ecifications.

New

roducts or u

dated

roduct information are desi

nated in blue font.

Floor

Ref. No. W H L Qty Type Qty Type 100% 115% 125%

2-5/16 x 9-1/2 MPH2395 -- -- 12 2-3/8 9-1/2 7 2 16d duplex 2 10d x 1-1/2 3855 3890 3915

2-5/16 x 11-7/8 MPH23118 WM3511.88 12 2-3/8 11-7/8 7 2 16d duplex 2 10d x 1-1/2 3855 3890 3915

2-5/16 x 14 MPH2314 -- -- 12 2-3/8 14 7 2 16d duplex 2 10d x 1-1/2 3855 3890 3915

2-5/16 x 16 MPH2316 -- -- 12 2-3/8 16 7 2 16d duplex 2 10d x 1-1/2 3855 3890 3915

2-5/16 x 18 MPH2318 -- -- 12 2-3/8 18 7 2 16d duplex 2 10d x 1-1/2 3855 3890 3915

2-5/16 x 20 MPH2320 -- -- 12 2-3/8 20 7 2 16d duplex 2 10d x 1-1/2 3855 3890 3915

2-1/2 x 9-1/4 MPH25925 -- -- 12 2-1/2 9-1/4 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 9-1/2 MPH2595 -- -- 12 2-1/2 9-1/2 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 11-1/4 MPH25112 -- -- 12 2-1/2 11-1/4 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 11-7/8 MPH25118 -- -- 12 2-1/2 11-7/8 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 14 MPH2514 -- -- 12 2-1/2 14 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 16 MPH2516 -- -- 12 2-1/2 16 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 18 MPH2518 -- -- 12 2-1/2 18 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 20 MPH2520 -- -- 12 2-1/2 20 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 22 MPH2522 -- -- 12 2-1/2 22 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 24 MPH2524 -- -- 12 2-1/2 24 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

2-1/2 x 26 MPH2526 -- -- 12 2-1/2 26 7 2 16d duplex 2 10d x 1-1/2 4145 4180 4205

3 x 9-1/4 MPH210-2 WM29.25-2 12 3-1/8 9-1/4 7 2 16d duplex 2 10d 4280 4280 4280

3 x 9-1/2 MPH1595-2 WM29.5-2 12 3-1/8 9-1/2 7 2 16d duplex 2 10d 4280 4280 4280

3 x 11-1/4 MPH15112-2 WM211.25-2 12 3-1/8 11-1/4 7 2 16d duplex 2 10d 4280 4280 4280

3 x 11-7/8 MPH15118-2 WM211.88-2 12 3-1/8 11-7/8 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 12 MPH3512 WMI412 12 3-1/2 12 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 14 MPH3514 WMI414 12 3-1/2 14 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 16 MPH3516 WMI416 12 3-1/2 16 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 18 MPH3518 WMI418 12 3-1/2 18 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 20 MPH3520 WMI420 12 3-1/2 20 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 9-1/4 MPH410 WM410 12 3-9/16 9-1/4 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 11-1/4 MPH412 WM412 12 3-9/16 11-1/4 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 9-1/2 MPH1795-2 WM3.56/9.5 12 3-5/8 9-1/2 7 2 16d duplex 2 10d 4280 4280 4280

3-1/2 x 11-7/8 MPH17118-2 WM3.56/11.88 12 3-5/8 11-7/8 7 2 16d duplex 2 10d 4280 4280 4280

4-5/8 x 11-7/8 MPH23118-2 WM3511.88-2 12 4-5/8 11-7/8 7 2 16d duplex 2 10d 4280 4280 4280

4-5/8 x 14 MPH2314-2 WM3514-2 12 4-5/8 14 7 2 16d duplex 2 10d 4280 4280 4280

4-5/8 x 16 MPH2316-2 WM3516-2 12 4-5/8 16 7 2 16d duplex 2 10d 4280 4280 4280

4-5/8 x 18 MPH2318-2 WM3518-2 12 4-5/8 18 7 2 16d duplex 2 10d 4280 4280 4280

4-5/8 x 20 MPH2320-2 WM3520-2 12 4-5/8 20 7 2 16d duplex 2 10d 4280 4280 4280

5-1/4 x 9-1/2 MPH5595 WM5.50/9.5 12 5-5/8 9-1/2 7 2 16d duplex 2 10d 4280 4280 4280

5-1/4 x 11-7/8 MPH55118 WM5.50/11.88 12 5-5/8 11-7/8 7 2 16d duplex 2 10d 4280 4280 4280

7 x 9-1/2 MPH3595-2 WMI49.5-2 12 7-1/8 9-1/2 8 2 16d duplex 2 10d 4280 4280 4280

7 x 11-1/4 MPH35112-2 WMI411.25-2 12 7-1/8 11-1/4 8 2 16d duplex 2 10d 4280 4280 4280

7 x 11-7/8 MPH35118-2 WMI411.88-2 12 7-1/8 11-7/8 8 2 16d duplex 2 10d 4280 4280 4280

7 x 14 MPH3514-2 WMI414-2 12 7-1/8 14 8 2 16d duplex 2 10d 4280 4280 4280

7 x 16 MPH3516-2 WMI416-2 12 7-1/8 16 8 2 16d duplex 2 10d 4280 4280 4280

7 x 18 MPH3518-2 WMI418-2 12 7-1/8 18 8 2 16d duplex 2 10d 4280 4280 4280

3-1/8 x glulam MPH325 -- -- 12 3-1/4 specify 7 2 16d duplex 2 10d 4280 4280 4280

5-1/8 x glulam MPH525 -- -- 12 5-1/4 specify 7 2 16d duplex 2 10d 4280 4280 4280

)

Masonr

com

ressive stren

th shall be minimum 1500

si.

)

NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" lon

10d nails are 0.148" dia. x 3" lon

16d du

lex nails are 0.162" dia. x 3-1/2" lon

double headed nails and shall be installed in

routed cells in accordance to manufacturer's installation s

ecifications.

New

roducts or u

dated

roduct information are desi

nated in blue font.

Engineered Lumber Sizes

8, F4,

R10

Beam/

Joist Size

USP

Stock No.

Code

Ref.

F4,

R10

Engineered Lumber Sizes

Dimensions (in)

Fastener Schedule

DF/SP

Allowable Loads (Lbs.)

Face

F4,

R10

Code

Ref.

Joist

Beam/

Joist Size

USP

Stock No.

F4,

R10

Dimensions (in)

Steel

Gauge

Face Joist

Roof

Fastener Schedule

DF/SP

Allowable Loads (Lbs.)

Engineered Lumber Sizes

Standard Lumber Sizes

Steel

Gauge

Roof

Continued on next page

Hangers

MPH

2-1/2"

3-3/4"

Summary of content (2 pages)

PAGE 1
Hangers MPH Masonry Hangers Install with (2) 16d duplex nails in grouted cell These hangers are designed to support standard lumber joists, I-Joists, or beams. Easy installation into concrete block walls makes the MPH an attractive alternative to fabricating seats in masonry (or attaching ledgers) to support joists or beams. L 3-3/4" H Materials: 12 gauge Finish: USP primer Options: All nominal lumber sizes are available for rough full size lumber. See Specialty Options Chart on page 135.
PAGE 2
1-3/4 x 14 1-3/4 x 16 MPH1714 MPH1716 WM14 WM16 12 12 1-13/16 1-13/16 14 16 7 7 2 2 16d duplex 16d duplex 2 2 10d x 1-1/2 10d x 1-1/2 2975 2975 3010 3010 3035 3035 1) Masonry compressive strength shall be minimum 1500 psi. Hangers 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d duplex nails are 0.162" dia. x 3-1/2" long, double headed nails and shall be installed in grouted cells in accordance to manufacturer's installation specifications.