Technical Specifications

222
General Hardware
© 2015 MiTek. All rights reserved.
ICPL / KNS1 / PL4 Protection Plates
Easy-to-install plates protect plumbing and
power/communication wiring from nail or
screw penetration.
ICPL58 – Installs with nails.
KNS1 & PL4 – Prongs allow for quick installation.
Materials: 16 gauge
Finish: ICPL516-TZ – G-185 galvanizing;
All others – G90 galvanizing
Options: See chart for Corrosion Finish Options
Codes: See page 11 for Code Reference Chart
Installation:
• Use all specied fasteners. See Product Notes,
page 17.
• 16 gauge steel conforms to protection shield
plate requirements of the National Electrical
Code and International Plumbing Code.
ICPL58
STS
PL4
Typical ICPL58
installation
Typical STS1
installation
KNS1
ICPL516-TZ
Typical ICPL516-TZ
installation
Ref. No. W H Qty Type F1 160% F1 160%
ICPL58 -- -- 1/16 8-1/16 5 4 8d or prongs -- -- -- -- -- --
PL4 NS2 1/16 2 5 -- -- prongs -- -- -- -- -- --
KNS1 NS1 1/16 1-1/2 3 -- -- prongs -- -- -- -- -- --
12 16d HDG + prongs Sill Plate 1355 1160
16 16d HDG + prongs Double Top Plate 1805 1550
1) Allowable loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2)
NAILS:
8d nails are 0.131" dia. x 2-1/2" long, 16d nails are 0.162" dia. x 3-1/2" long.
Dimensions (in)
Fastener Schedule
2
5
Code
Ref.
DF/SP
Allowable
Loads (Lbs.)
1
S-P-F
Allowable
Loads (Lbs.)
1
100
Corrosion
Finish
USP
Stock No.
Steel
Thickness
Installation
Type
ICPL516-TZ PSPN516Z 1/16 16-1/4
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Typical KNS1 & PL4
installation
Stud shoes reinforce joists, plates, studs, or rafters which
have been drilled or notched during construction.
Materials: 16 gauge
Finish: G90 galvanizing
Codes: See page 11 for Code Reference Chart
Installation:
• Use all specied fasteners. See Product Notes, page 17.
• STS units are not structurally rated and should not be used
as a total member replacement in structural applications.
• For use with 2" O.D. pipe.
STS Stud Shoes
Dimensions (in)
Ref. No. Description W Qty Type
STS1 SS1.5 16 Single Stud 1-9/16 10 10d x 1-1/2
STS2 SS3 16 Double Stud 3-1/16 12 10d
STS3 SS4.5 16 Triple Stud 4-9/16 14 10d
1) Minimum nail penetration shall be 1-1/2" for 10d nails.
2) Maximum hole size = 2".
3) NAILS: 10d x 1-1/2" nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long.
120
USP
Stock No.
Steel
Gauge
Fastener Schedule
1,2,3
Code
Ref.
1) Minimum nail penetration shall be 1-1/2" for 10d nails.
2) Maximum hole size = 2".
3) NAILS: 10d x 1-1/2" nails are 0.148" dia. x 1-1/2" long,
10d nails are 0.148" dia. x 3" long.
W
W
H
W
H
5"
2-1/2"
2-5/8"
W
General Hardware
W
H
H