Technical Specifications
214
Deck & Fences
© 2015 MiTek. All rights reserved.
The CSH-TZ concealed stringer hanger provides a method of connecting
a stair stringer with a hidden hanger. The seat of the hanger is adjustable
to match the slope of the stair stringer.
The reversible design allows the connector to be used on the left, right,
or interior stringers. The CSH-TZ may be used with USP’s SCA Stair Angles
for a complete, easy-to-use stair framing solution.
Materials: 18 gauge
Finish: G-185 galvanizing
Codes: See page 11 for Code Reference Chart
Patents: #7,631,463
Installation:
• Use all specied fasteners. See Product Notes, page 17.
• Bend angle only once.
Steps:
1. Attach CSH-TZ to header with tabs positioned towards the inside of the
stringer member.
2. Adjust the seat of the CSH-TZ to match the slope of the stringer member.
Diamond shaped holes in the connector allow temporary installation of
woodscrews to aid in installation of the CSH-TZ.
3. Install 10d x 1-1/2" nails into the stringer and header members.
SDJT14-TZ
Typical CSH-TZ
installation
CSH-TZ
CSH-TZ Concealed Stringer Hanger
Deck & Fences
Typical SDJT14-TZ
installation
SDJT Deck Joist Tie
Secures 2x joists to posts.
Materials: 14 gauge
Finish: G-185 galvanizing
Codes: See page 11 for Code Reference Chart
Installation:
• Use all specied fasteners. See Product Notes, page 17.
• Use with 2x lumber for joists (minimum height is 2x4). Install
with either specied nails or through bolts. Do not use lag bolts.
To ease installation, attach to 4x4 post rst.
Ref. No. Qty Type Qty Dia. 100% 115% 125% 100% 115% 125%
4 x 4 SDJT14-TZ DJT14Z 14 8 16d HDG 2 3/8 HDG 1120 1290 1400 1400 1400 1400 130
1) Bolts shall conform to ASTM A 307 or better.
2)
NAILS:
16d HDG nails are 0.162" dia. x 3-1/2" long.
DF/SP
Allowable Loads (Lbs.)
Fastener Schedule
Code
Ref.
Post
Size
Nails Bolts
USP
Stock No.
Steel
Gauge
Nails
2
Bolts
1
Corrosion
Finish
Uplift
1
Uplift
1
Ref. No. Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
CSH-TZ LSCZ 18 8 10d x 1-1/2 HDG 5 10d x 1-1/2 HDG 890 890 890 390 745 745 745 310
31, F32, R1
1) Uplift loads are increased 60% for wind or seismic loads; no further increase shall be permitted.
2)
NAILS:
10d x 1-1/2 HDG nails are 0.148" dia. x 1-1/2" long.
New products or updated product information are designated in
blue font
.
Code
Ref.
Fastener Schedule
2
USP
Stock No.
Steel
Gauge
Rim Joist Stringer
DF/SP
Allowable Loads (Lbs.)
S-P-F/Hem Fir
Allowable Loads (Lbs.)
Corrosion
Finish
3-1/8"
3-1/8"
2-3/4"
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Adjustable
5"
5"
1-7/16"
1-1/2"