PRODUCT CATALOG 60TH EDITION
MITEK IS MORE THAN JUST ENGINEERED PRODUCTS ENGINEERED PRODUCTS Our products save on labor and installation costs and help provide code compliant and safe, resilient homes. MiTek-US.com/Products SOFTWARE We’re optimizing the workflow of your business, improving accuracy and reducing waste with our software solutions. MiTek-US.
What's New at MiTek? MiTek® IHFL (18GA) /IHF (16GA) Face Mount I-Joist Hangers IHFL/IHF hangers feature speed prongs for temporary placement and seat cleats to grab the bottom flange of the supported I-joist. Diamond holes in header and joist allow for optional Max nailing for customized fastening to match allowable load needed, saving you time and money on the jobsite. See page 206 for details.
Directory of Products Code Evaluation Information . . . . . . . . . . . . . 10 Corrosion Information . . . . . . . . . . . . . . . 11-16 Design Notes . . . . . . . . . . . . . . . . . . . . . 18-19 Installation Notes . . . . . . . . . . . . . . . . . . . . . 19 New Products . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Information . . . . . . . . . . . . . . . . . . . 17 Product Notes .
MiTek Products Alphabetical Index A ——————————————------------------A Angle Clip . . . . . . . . . . . . . . . . . . . . . 108-109 AB Anchor Bolts . . . . . . . . . . . . . . . . . . . . . . 51 AC Angle Clips . . . . . . . . . . . . . . . . . . . 108-109 ADTT Adj. Deck Tension Tie . . . . . . . . 182, 298 Alternate Installations . . . . . . . . . . . . . . . 287 ANJ Heavy Angles . . . . . . . . . . . . . . .
MiTek Products Alphabetical Index L ——————————————------------------- L Straps . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 LBP Bearing Plates . . . . . . . . . . . . . . . . . . . . 51 LBPS Bearing Plates . . . . . . . . . . . . . . . . . . . 51 LDSC Drag Strut Connectors . . . . . . . . . . . . 282 LFTA Strap . . . . . . . . . . . . . . 130-131, 262-264 LGU Girder Hanger . . . . . . . . . .
MiTek Products Alphabetical Index SFP Fence Post Connectors . . . . . . . . . . . . 305 SHA Masonry Uplift Connectors . . . . . . . . . 255 SKH Skewed 45° Hangers . . . . . . . . . . . 175-176 SKHH Skewed 45° Hangers . . . . . . . . . 175-176 SMP Fence Post Connectors . . . . . . . . . . . . 305 SNP Skewed Nail Plate . . . . . . . . . . . . . . . . 280 Specialty Options . . . . . . . . . . . . . . .
Reference Number Index About the Reference Numbers Reference numbers shown throughout the charts in this catalog are part numbers which may be more familiar to customers in various regions of the United States. These are included for the convenience of our new customers who have recently switched from a competitor’s product line to MiTek. The reference numbers in this catalog are for general application comparison only and should not be used as a substitution tool.
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved Reference Number Index MUS Hanger . . . . . . . . . . . 142-143, 154-155, 268 Nails . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24, 343 NCA Nailless Bridging . . . . . . . . . . . . . . . . . . . 315 NS Nail Stopper . . . . . . . . . . . . . . . . . . . . 310, 349 NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Code Evaluation Information Code Reference Column Chart Listing Code Evaluation Labeling Requirements: Most structural products shown in this catalog are listed in a current code evaluation report from the code evaluation agencies listed. Labeling products for field identification is part of our quality assurance program. Code evaluation agencies require that the label include the manufacturer’s name or trademark, the model number, and code evaluation identification number.
Corrosion Information For the majority of applications, metal hangers and connectors are used in interior, above ground, dry service conditions. They are typically not being exposed to corrosive environments which can significantly reduce their strength and longevity. What is Corrosion? Corrosion is the destructive degradation of steel due to its interaction with the environment. Here the steel is the connector and the environment is whatever the connector interacts with, namely wood and air.
Corrosion Information Relative Corrosion Resistance Capability: The chart below ranks the available options in terms of their relative effectiveness against corrosion. As expected, the ability to resist corrosion increases with increasing zinc thickness, so G185 is the most durable pre-galvanized product available. Gold Coat offers enhanced protection compared to G185 while stainless steel offers the best protection for most applications.
Corrosion Information The Structural Connectors Coating Recommendations chart below was developed by reviewing field service performance and accelerated corrosion test results. They are offered as general guidelines and are not intended to cover all possible service conditions. Additional consideration may also be needed for: wet service conditions preservation treated lumber fire retardant treated lumber strength reducing chemicals building near salt water coastal areas.
Corrosion Information Corrosion Resistant Finishes MiTek offers several corrosion resistant finishes to cover a range of corrosion performance. For products available in corrosion resistant finishes, reference the “Corrosion Finish” column in the charts and Corrosion Key located by the chart footnotes or pages 15-16 for a complete listing of corrosion resistant products.
Corrosion Information Corrosion Resistant Product Offering Copyright © 2020 MiTek Industries, Inc. All Rights Reserved MiTek Stock No. Triple Zinc Hot-Dip Exterior Galv.
Corrosion Information Corrosion Resistant Product Offering 16 Stainless Steel (SS) MiTek Stock No. Triple Zinc Hot-Dip Galv.
Product Information U.S. Standard Steel Gauge Equivalents in Nominal Dimensions Approximate Dimensions Gauge 3 7 10 11 12 14 16 18 20 22 Inches 1/4 3/16 9/64 1/8 7/64 5/64 1/16 3/64 1/32 1/32 Special & Custom Connectors Decimals (inches) Millimeters 6.0 4.5 3.4 3.0 2.7 2.0 1.5 1.2 1.0 0.8 Uncoated Steel 0.238 0.171 0.129 0.114 0.099 0.070 0.055 0.044 0.033 0.029 Galvanized Steel (G90) -0.186 0.138 0.123 0.108 0.078 0.063 0.052 0.040 0.033 Triple Zinc (G-185) --0.140 0.125 0.110 0.080 0.065 0.054 0.
General Information Product Notes 1) This catalog reflects the most current information available at the time of printing. However, we are continually improving our products through better engineering design and development and recommend visiting our website for the latest on-line version of the catalog at MiTek-US.com. MiTek reserves the right to change specifications, designs, and models at any time without notice and liability for such changes.
General Information Material MiTek selects steel for its various products in accordance with application needs and steel properties, including tensile strength, ductility, corrosion resistance, gauge, and weldability. See specific code evaluation reports or consult MiTek for additional steel information on specific products. products are manufactured from steel which meets ASTM A 653, ASTM A 1011, or ASTM A 36, ASTM A1018 or ASTM A666 standards.
Fasteners Fasteners Fasteners pg. 22-39 Bolts 38 Fastening Identification / Features 39 22-24 Screws 25-37 20 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Fasteners Copyright © 2020 MiTek Industries, Inc.
Fasteners N / NA Nails Fasteners Proper fasteners are a critical component in a sound wood frame structure. To ensure successful installations of its connectors, MiTek offers a full range of structurally-rated nails. All galvanized nails supplied by MiTek are Hot-dipped for greater corrosion resistance. Any MiTek connector requiring a NA16D-RS or NA20D nail is shipped with the nails attached to the connector in convenient poly bags. NA11 .131 x 1-1/2" N8-GC .
Fasteners N / NA Nails Fasteners DF/SP Allowable Shear per Nail (Lbs.)1,2,4,5 Dimensions (in) Finish3,7 HDG GC SS8 Bright Size 8d x 1-1/2 10d x 1-1/2 10d Common 16d x 2-1/2 16d Common 20d x 2-1/2 8d x 1-1/2 10d x 1-1/2 10d Common 16d Common 8d x 1-1/2 10d x 1-1/2 8d Common 10d Common 16d Common 8d Common 10d Common 16d Sinker 16d Ring Shank 16d Common 20d Common MiTek USP Stock No.
Fasteners Fasteners MiTek® TECO™ 33º Collated Nails MiTek® TECO™ 33° collated pneumatically driven nails feature a color coded head-ID stamp system that makes it easy to verify the proper nail has been used. The 33° collated nails can serve as an alternate to hand-driven installation of the following nails and may be used with many MiTek products.
Fasteners WS Hex Head Interior Structural Wood Screws Fasteners The WS Wood Screw is a self-drilling screw used for numerous interior framing applications. For use in wood-to-wood and steel-to-wood applications. Head stamped to indicate length for easy inspection.
Fasteners Fasteners WSWH Washer Head Interior Structural Wood Screws The MiTek Pro Series Washer Head is the ideal screw for interior Multi-Ply EWP and dimensional wood connections. The specific lengths of the WSWH allow for one-sided connections on multi-ply beams and girder trusses.
Fasteners WSWH Washer Head Interior Structural Wood Screw Application Fasteners Attaching 2x Ledger-to-Wall Studs Application 2 Layers of 5/8" Gypsum Wallboard Stud Wall MiTek’s WSWH Washer Head Structural Wood Screw can be used to attach a ledger to studs directly, through 1/2" APA rated sheathing or through one or two layers of 5/8" gypsum wallboard (drywall).
Fasteners Fasteners WSWH Washer Head Interior Structural Wood Screw Application Joining Multi-Ply Dimensional Lumber Beams Application The MiTek Pro Series WSWH Structural Wood Screws have been designed specifically for use in joining wood members of multiple-ply dimensional lumber beams. Using a standard 1/2'' low speed/high torque drill, install screws into the side of the outermost ply. As the threads fully engage the final ply, allow the underside of the washer head to pull the plies firmly together.
Fasteners WSWH Washer Head Interior Structural Wood Screw Application Fasteners Fastener Size Selection by Assembly Type (2 rows shown) A 1-1/2" B 1-1/2" 1-1/2" 1-1/2" C 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 2-7/8" Screw WSWH278 2-7/8" WSWH45 4-1/2" WSWH6 6" Side Loaded Beams Where floor joists are joined to the side of the beam (typically using a joist hanger), this load chart must be used to establish the proper pattern based on the design load as determined by the engineer and noted on th
Fasteners Fasteners WSWH Washer Head Interior Structural Wood Screw Application Joining Multi-Ply Engineered Wood (EWP) Beams Application The MiTek Pro Series WSWH Structural Wood Screws have been designed specifically for use in joining wood members of multiple-ply engineered wood beams (LVL, LSL & PSL). Using a standard 1/2'' low speed/high torque drill, install screws into the side of the outermost ply.
Fasteners WSWH Washer Head Interior Structural Wood Screw Applications Fasteners Fastener Size Selection by Assembly Type (2 rows shown) 1-3/4" A 1-3/4" 1-3/4" B 1-3/4" 1-3/4" 3-1/2" C 1-3/4" WSWH5 5" WSWH338 3-3/8" D 1-3/4" 1-3/4" 3-1/2" E WSWH634 6-3/4" 3-1/2" WSWH5 5" 3-1/2" F 1-3/4" 1-3/4" 1-3/4" 1-3/4" WSWH634 6-3/4" WSWH634 6-3/4" Side Loaded Beams Where floor joists are joined to the side of the beam (typically using a joist hanger), this load chart must be used to establish
Fasteners The MiTek Pro Series Hex Head is the ideal screw for numerous framing applications. It can be used in wood-to-wood and steel-to-wood applications. Features and Benefits: • 1/4" diameter • No predrilling • Type 17 point reduces installation torque and splitting • 3/8" hex drive • Length identification stamps on all WS heads Materials: 1/4" diameter Grade 5 steel Finish: Exterior Coat Codes: IBC, FL, LA Installation: • Screws are self-drilling.
Fasteners WSWH Washer Head Structural Exterior Wood Screws Fasteners The WSWH is an ideal alternative for the Pro or DIYer to traditional lag screws and through-bolts, for installing deck ledgers and more. It is easy to install and reduces labor on the jobsite. The large, flat washer head maximizes bearing area and allows for less interference after installation.
Fasteners Fasteners WS /WSWH Exterior Structural Wood Screw Application Attaching Deck Ledger to Rim Board Application The MiTek WS structural wood screws can be used to fasten deck ledgers to the rim board (AKA band/rim joist) of structures to meet the connection requirements of the International Residential Building Code (IRC). Both the standard hex head (WS-EXT) and washer head (WSWH-EXT) styles may be used for this purpose. Table R507.9.1.
Fasteners WSBH Bugle Head Structural Exterior Wood Screws Fasteners The WSBH is a multi-purpose structural wood screw ideal for a low profile appearance in wood-to-wood connections. This structural wood screw allows the Pro Contractor or DIYer to drive the head flush or countersink it below the wood surface. The WSBH is easy to install and a high strength alternative to traditional lags, bolts and pole barn nails.
Fasteners Fasteners LL LumberLok Exterior Structural Connector Screws The LumberLok Exterior Structural Connector Screw is a self-drilling screw that can be used with a number of MiTek connectors and also for wood-to-wood applications. The screws feature a T20* drive head with integral washer and gimlet point for ease of installation. The twin-lead threads drive in twice as fast as the single lead threads significantly reducing installation time.
Fasteners LL LumberLok Exterior Structural Connector Screws Fasteners Common Deck Connectors that are Compatible with LumberLok Structural Connector Screws This is not a complete list of MiTek connectors that are compatible with LumberLok Structural Connector Screws. Most connectors that are installed with nails can also be installed with LumberLok Structural Connector Screws.
Fasteners Fasteners B Bolts For customer convenience, we offer a wide range of bolts specified for the MiTek product line. Each bolt is shipped with two washers and one hex nut. L Materials: Bolts and nuts are standard hex head conforming to ASTM A 307 Grade A or SAE Grade 2 or better. Washers conform to American National Standard Type A plain steel, ANSI B.22.1.
Fasteners Fastening Identification / Features Always fill all (normal-size) round nail holes, unless otherwise noted. Seat Cleat® helps lock I-Joist into place for positive seating and nailing ease Do not nail through the Seat Cleat® Diamond Holes: Optional nailing for maximum listed capacity or for temporary hanger fastening during installation.
Concrete & Masonry Anchor Bolts Anchor Rod Chairs Anchoring Epoxy pg.
Concrete & Masonry Anchoring Epoxy Concrete & Masonry Product Offering Overview Cracked / Uncracked Concrete Masonry DOT & General Purpose Uncracked Concrete Bonding / Repair CIA-GEL 7000-C CIA-GEL 7000 CIA-GEL 6000-GP CIA-EA IB-9 Estimate how much epoxy your job needs. Quickly calculate the number of required cartridges using the Epoxy Quantity Estimator. Run our web application on your desktop, smart phone or tablet. The Estimator works with threaded rods or rebar.
Anchoring Epoxy Concrete & Masonry CIA-GEL 6000-GP Epoxy Concrete & Masonry CIA-GEL 6000-GP is a superior epoxy specifically designed for general purpose structural applications that require quick load times and for doweling applications requiring state DOT approval. It is a two-component (1:1 ratio) adhesive epoxy with 100% solids and is solvent free, moisture insensitive, non-sag and odorless.
Concrete & Masonry Concrete & Masonry DUC Ductile Undercut Anchors DUCs are mechanical anchors expanded into holes that have been undercut at the bottom using an undercutting drill bit. This creates a true bearing type anchor that performs like a cast-in-place headed anchor. Load is transferred into the concrete through bearing, not friction like traditional expansion anchors. Excellent performance in seismic and dynamic loading conditions.
Concrete & Masonry PFM Concrete Screw Anchors Screw-Bolt+ anchors are a one-piece, heavy duty screw anchor with a finished hex head. The patented thread design, designed for use with standard ANSI drill bits, reduces installation torque and enhances productivity. The steel threads along the anchor body tap into the hole during installation to provide keyed engagement and allow for reduced edge and spacing distances. Hex Head Washer Codes: IBC, FL, LA Copyright © 2020 MiTek Industries, Inc.
Power-Stud® HD5 Wedge Expansion Anchors Concrete & Masonry Concrete & Masonry The Power-Stud® HD5 anchor is a fully threaded, torque-controlled, wedge expansion anchor. Suitable base materials include normal-weight concrete, sand-lightweight concrete and grouted concrete masonry. Nut and washer are included.
Concrete & Masonry THR Threaded Rods THR’s support the deck oriented code requirements for mechanically reinforced railing post and deck to house ledger board attachments. Materials: ASTM A36 steel, also conforms to ASTM F1554, Grade 36 Finish: Hot-dip galvanized Concrete & Masonry L Installation: • Install into wet concrete with nut embedded or drill minimum 1/16" – 1/8" oversized hole depending on rod size and secure with anchor epoxy. Nut and washer included.
Concrete & Masonry ARC Anchor Rod Chairs Concrete & Masonry When attached to the forms, the ARC allows for easy and precise placement of anchor rods prior to pouring concrete. The “chair” and nut are pre-assembled for quick installation.
Concrete & Masonry STB / STBL Anchor Bolts 1-3/4" min. edge distance Embossed ends provide guides for embedment angle and depth. An embedment line is embossed on the shaft for easy installation. Features rolled threads for high tensile strength.
Concrete & Masonry STB / STBL Anchor Bolts Concrete Block Applications – Prior to cell pour, install the STB or STBL in an upright position and at a 45° angle to the wall. (See illustrations.) Use the embossed angle guide on the end of the STB or STBL shaft as a guide. Install one horizontal #4 rebar at a depth of 4" and one vertical #4 rebar maximum 48" o.c. spacing. Fill all cells with concrete having a minimum 2,500 psi compressive strength.
Concrete & Masonry AB Anchor Bolts The AB anchor bolt provides an economical way to meet the prescriptive requirements of the 2018 IRC for securing mudsill plates to a concrete or masonry foundation. The bolt is manufactured from ASTM 1554 steel and has a hot-dip galvanized finish. A nut (ASTM A 563) and washer (ASTM F 844) are included. In some jurisdictions, a plate washer may be required. Check with your local Building Official.
Concrete & Masonry ATR All Thread Rods ATR All Thread Rod is a continuously threaded low carbon steel rod that may be used for anchoring MiTek’s holdowns, tension ties and wood structural panel shear walls to concrete. They can also be used for many other general purpose tension transfer fastening needs. Concrete & Masonry Materials: ASTM A307 Grade A Finish: None or Zinc Plated (See Chart) Installation: • A TR All Thread Rod can be cast-in-place or epoxied into concrete.
Concrete & Masonry CNW Coupler Nuts The MiTek CNW coupler nut is designed to join threaded rods to embedded anchor rods. They are also used in the Z4 Tie Down system to attach Z-Rods together (See Z4 Product Catalog). The coupler nut has an inspection hole with an internal positive stop that allows easy verification that the ends of both rods have been fully threaded.
Concrete & Masonry HN Hex Nuts The HN nut is a standard hex nut manufactured from low carbon ASTM A563 Grade A steel (Proof Load = 90 ksi) which makes it applicable for many common ASTM steel threaded rods of equivalent or lower strength. Concrete & Masonry Materials: ASTM A563 Grade A Finish: See chart Finish None MiTek USP Stock No. Ref. No. HN38 -HN12 -HN58 -HN34 -HN78 -HN1 -HN118 -- Dia. (in) 0.375 0.500 0.625 0.750 0.875 1.000 1.125 Code Ref. Finish Zinc Plated -- MiTek USP Stock No.
Concrete & Masonry FA Foundation Anchor For installation into concrete slabs. The FA3 features a split flange for nailing to both mudsill and stud for greater framing versatility. Materials: 16 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: See chart for code references Embossed lines provide guide for matching to edge of form board 1-1/2" 4-5/8" Concrete & Masonry Installation: • Use all specified fasteners. See Product Notes, page 18.
Concrete & Masonry FA Foundation Anchor 3-1/2" Materials: 16 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: See chart for code references 4-1/8" Installation: 5-3/16" • The FA4 can be mounted to the form board before placing the concrete or inserted into the wet concrete after it is poured. See Detail A installation. • Place the mudsill in position after the concrete cures.
Concrete & Masonry ST Foundation Anchors ST1-TZ – For installation into concrete slab or poured stemwalls. The ST1-TZ features a prebent base flange to assure proper anchoring into concrete ST2-TZ – For installation into concrete slab, poured stemwalls or concrete/masonry. The ST2-TZ features a prebent base flange to assure proper anchoring into concrete Installation: • Use all specified fasteners. See Product Notes, page 18. • Use a minimum of two anchors per mudsill.
Concrete & Masonry FWAN Foundation Wall Anchor The FWAN-TZ offers two methods of installation: 1. Centered Installation • Compatible with joist/blocking up to 3-1/2" wide • Highest load capacities for transfer of out-of-plane loads into floor framing • Rim board splices allowed anywhere along the wall 2.
Concrete & Masonry SRCP Sill Retrofit Connector Plate F2 F1 F3 Sill plate Foundation wall 6" WS3 structural wood screw The SRCP Sill Retrofit Connector Plate can be installed without shims anywhere the face of the sill plate is within 1/2" of the face of the foundation wall.
Concrete & Masonry SRC Sill Retrofit Connector Concrete & Masonry The SRC Sill Retrofit Connector has been engineered as a ductile retrofit for older buildings in high seismic zone regions that require additional reinforcement. It can be installed where there is minimal space between the floor framing and top of the foundation wall. The SRC can also be used to reinforce buildings in high velocity wind zones.
Concrete & Masonry SFA / SFJA Foundation Anchors SFA – Mudsill anchors for retrofit applications. Features a slotted bend line for easy adjustment when foundation walls are slanted Uplift F1 SFJA – Ties floor joists directly to foundations with bolt fastening Concrete & Masonry Materials: 12 gauge Finish: G90 galvanizing 1/2" max gap distance Installation: • Use all specified fasteners. See Product Notes, page 18. • A design professional must specify anchor bolt type, length, and embedment.
Concrete & Masonry KGLB / KGLBT / KHGLB Laminated Beam Seats Uplift KGLB – Single bolt, bearing only F2 KGLBT – Double bolt with structural tee provides uplift and horizontal resistance 1/2" min clearance W 3" F2 Concrete & Masonry KHGLB – Double bolt design provides uplift and horizontal resistance T L Bearing plate Materials: Flanges – 1/4" steel Bearing Plate – See chart for “T” dimension Anchor Dowels – 3⁄4" x 12" rebar Finish: Primer Options: Consult MiTek for non-catalog variations.
Concrete & Masonry KGH Floor Girder Hangers Connects girder beams to foundation walls and eliminates the need to block out pockets or inserts while forming foundation. Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • H dimension assumes 2x mudsill. For 3x or larger mudsill, please contact factory. • The 1-1⁄2" hole, centered in the saddle, allows for installation over any protruding foundation bolts. This is not required.
Holdowns Holdowns Holdowns Foundation Straps Holdowns pg. 66-79 73-77 66-69, 72 78-79 Tension Ties 70-71 64 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Holdowns Copyright © 2020 MiTek Industries, Inc.
Holdowns PHD / DTB Holdowns PHD predeflected holdowns feature the predeflected base, minimizing deflection while providing uplift resistance. Installs with screws eliminating the need for predrilling and potential fastener slip. No thru bolts to countersink. DTB-TZ is a light capacity holdown for single 2x installations. Materials: See chart Finish: G90 galvanizing; DTB-TZ – G-185 galvanizing Installation: • Use all specified fasteners. See Product Notes, page 18.
Holdowns UPHD Holdowns Engineered for high capacity with minimum deflection and low eccentricity. Installs with screws eliminating the need for predrilling and potential fastener slip. No thru bolts to countersink. Materials: See chart Finish: Primer Codes: IBC, FL, LA H Installation: • Use all specified fasteners. See Product Notes, page 18. • Place holdown over anchor bolt and drive screws into post. • Tighten anchor bolt nuts finger tight to base plus 1/3 to 1/2 additional turns with a wrench.
Holdowns TD / TDX Holdowns TD – Different welded configurations and sizes achieve a great deal of versatility within the TD series. Moisture barrier may be required TDX – The TDX2 and TDX5 feature formed designs, all others are welded. All are self-jigging. All models, except TD2, TD5, and TD7, feature a self-jigging design with code required end distances built in. (End distance = 7 bolt diameters from the top of the sill to the center of the first bolt hole in the studs or post.
Holdowns Fastener Schedule4 Dimensions (in) MiTek USP Steel Stock No. Ref. No. Gauge TD5 TD7 TD9 TD15 TDX2-TZ Copyright © 2020 MiTek Industries, Inc.
HTT Tension Ties Holdowns Secures multi-ply studs or posts to mudsills or foundation. Nail fastening makes for a convenient connection to studs or posts in cramped retrofit installations. Holdowns Materials: See chart Finish: G90 galvanizing Codes: See chart for code references Installation: • Use all specified fasteners to attach the strap portion of the connector to the side of stud, post, joist, purlin, or beam. Secure the base to the concrete or masonry wall with specified anchor bolt.
Holdowns LTS / LTTI Tension Ties LTS series – The LTS19 is designed for nail-on installation to 2x joists or studs, and the LTS20B provides a nail or bolt fastening option. The LTS20B will accommodate wood I-Joists if 10d (0.148") x 1-1⁄2" nails are used instead of the specified 16d nails. W Hanger not shown W 2-1/2" 6-1/4" L 3-3/4" L LTTI31 – An open web joist tension tie designed for use with masonry or concrete construction.
Holdowns Holdown Offset Anchor Bolt Notes Allowable loads and deflection values for holdowns such as TD, PHD, TDX, HTT and UPHD are based on installation with the anchor bolt aligned directly below the centerline of the holdown. The maximum tolerances for anchor bolt offset are described below. Full height stud or post per plan Designer should consider that installation of a holdown raised above the sill plate may result in higher deflections.
Holdowns TA Foundation Straps Foundation Straps offer an economical, one-piece method of achieving a continuous load path from a 2 x 8 or 2 x 14 dimensional rim joist through concrete block to foundation. All models require a 6" embedment into concrete footings. 2 x 10 rim joist Materials: 12 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options 6" min. Installation: • Use all specified fasteners. See Product Notes, page 18.
Holdowns LSTAD / STAD Foundation Straps The coined dimples below the embedment line allow for increased concrete bonding. These holdowns retain high uplift capacity even when installed at corners of foundation stemwalls. Ideal for use with built up 2x end posts. Edge distance 1/2" min from corner RJ after the model indicates LSTAD or STAD for rim joist applications as in STAD8RJ. Rim joist models provide for a 17" clear span without the loss of strap nailing.
LSTAD / STAD Foundation Straps Holdowns Copyright © 2020 MiTek Industries, Inc.
Holdowns HPAHD / PAHD Foundation Straps Designed to anchor wood framing to poured concrete foundations.
Holdowns HPAHD / PAHD Foundation Straps HPAHD22 / PAHD42 Load Table Concrete Stemwall Minimum Thickness (in) Dimensions (in) MiTek Stock No. Ref. No. Ga. W L IE D DF/SP Allowable Tension Loads (Lbs.)5 Fastener Schedule1 Uncracked Cracked Code Type10 Corner2 Midwall3,4 Corner2 Midwall3,4 Ref.
Holdowns HPA / PA / PAI Purlin Anchors HPA series – For installation into poured concrete walls, foundations, or masonry. The HPA is the heavy-duty version of the PA anchor. PA series – For installation into poured concrete or concrete block walls and foundations. PAI series – For wood I-Joist applications. An expanded 3" on-center nail spacing reduces splitting along I-Joist flange.
HPA / PA / PAI Purlin Anchors Holdowns Wind and ASCE Seismic Design A & B PA18 PA18 PA23 PA23 L (in) Masonry Ref. No. Concrete MiTek Stock No. 18-1/2 4 6 23-3/4 4 6 Fastener Schedule Ledger / Plate Size None 2x & 3x 4x None 2x & 3x 4x Min 4,5,7,8 Qty Type Uncracked Concrete Cracked Concrete 12 16d 2975 2770 15 16d Bolts Fastener Schedule Allowable Tension 160% 3720 2770 Min 4,5,7,8 Qty 12 11 10 Type 16d Min 4,5,7,8 Masonry Qty 2680 2 Allowable Tension 160% Bolt Dia.
Caps & Bases Caps & Bases Caps & Bases pg. 82-105 88-91 Column Caps 99-105 Post Anchors 82-85, 92 Post Bases 86-87, 98 Post Caps 80 93-97 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Caps & Bases Copyright © 2020 MiTek Industries, Inc.
Caps & Bases PA / PAE / PAU Post Anchors Uplift Post Anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1" stand-off plate to elevate wood posts above concrete surfaces as required by building code.
Caps & Bases PA / PAE / PAU Post Anchors Post/ Column Size MiTek USP Stock No. Ref. No. PA44 4x4 4 x 4 Rough 4x6 -- Post Anchor Bolt W H L Nails Uplift1 Bolts Dia. Dia.
Caps & Bases RPB Retrofit Post Base RPB-TZ post base attaches 4x4 or larger wood posts to concrete or wood surfaces after the post is in place. Can be installed with 1 or 2 RPB-TZs (single or double). Post may also be installed on our CPB composite post base product which provides a 1" stand off as required in untreated wood installations.
Caps & Bases WAS / WE Wet Post Anchors Uplift WAS – A formed base providing a 1" stand-off with high bearing capacity. Uplift F1 F2 F2 F1 F1 Download Min edge distance = 1.5 x H 2 Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA IRC R317.1.4, IBC 2304.12.2.2, IRC R407.3, IBC 2304.10.7 Min edge distance = 1.5 x H 2 Typical WAS installation Typical WE installation W1 L H1 H1 11-3/16" W2 1" H2 H2 Post Size MiTek Stock No. Ref.
Caps & Bases EPB Elevated Post Bases The EBP44T-TZ Elevated Post Base is an economical solution for supporting 4x4 posts at the minimum 1 inch above the concrete foundation as required by the building code. For applications where uplift loads are not present, the EPB44T-TZ can be installed directly into a hole predrilled in a pier block or concrete foundation as shown in Figure A below. To resist uplift loading, the EPB44T-TZ must be cast into concrete or epoxied into place as shown in Figure B below.
Caps & Bases EBG / EPB / EPBH Elevated Post Bases Uplift These post bases allow installers to pre-align posts and preset post heights above concrete floors or footings. By eliminating post-to-concrete contact, moisture damage is reduced. Elevated post bases are ideal for building carports, decks or porches. All series feature convenient nail fastening to post. 1" max.
Caps & Bases KCB Column Bases Provides high structural capacity and installs with bolts providing an architectural appearance. Uplift Materials: See chart Finish: KCB (5/8" bolt models) – G90 galvanizing; KCB (3/4" bolt models) – Primer Options: KCB models available in rough/full size. See chart for Corrosion Finish Options Codes: IRC R407.3, IBC 2304.10.7 3" min. edge distance Installation: • Use all specified fasteners. See Product Notes, page 18.
Caps & Bases KCBQ Column Bases High capacity column base fastens to column with MiTek’s WS structural wood screws. Uplift Materials: 10 gauge Finish: G90 galvanizing Options: KCBQ models available in rough/full sizes See chart for Corrosion Finish Options Codes: IRC R407.3, IBC 2304.10.7 3” min. edge distance Installation: • Use all specified fasteners. See Product Notes, page 18. • MiTek’s WS2 structural wood screws, 1/4" dia. x 2" long, are supplied with KCBQ Column Bases.
Caps & Bases CBE Column Bases 12 gauge base for carports, patios, or other residential framing. Materials: 12 gauge Finish: G90 galvanizing Codes: IBC, FL, LA IRC R407.3, IBC 2304.10.7 Uplift 1.5 x embedment (typical for all edges) Installation: • Use all specified fasteners. See Product Notes, page 18. • Not recommended for fence posts or other unrestrained (not fixed or fastened at top) applications. These bases are not designed to resist overturning (moment) loads.
Caps & Bases CBSQ Column Bases These column bases install using MiTek’s WS2-EXT structural wood screws, reducing installation time and cost. Designed for high uplift in high wind or seismic applications. Includes a stand-off plate to protect the wood from ground contact moisture as required by building code. Uplift Bearing Materials: See chart Finish: G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: IRC R317.1.4, IBC 2304.12.2.2, IRC R407.3, IBC 2304.10.
Caps & Bases D Post Anchors Secures nominal sized posts to wood surfaces for light-duty applications. Uplift Materials: 18 gauge Finish: G90 galvanizing; D44-TZ & D46R-TZ - G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA F2 F1 F1 F2 Installation: • Use all specified fasteners. See Product Notes, page 18. • Not recommended for fence posts or other unrestrained (not fixed or fastened at top) applications.
Caps & Bases BC / BCS / C Post Caps Uplift BC – One-piece design for double 2x’s to a 4x post F2 BCS – One-piece design connects 2-ply or 3-ply beams to the tops of 4x4 or 6x6 post.
Caps & Bases EPCM / PCM Post Caps PCM – Provides a positive connection for medium-duty, post-to-beam applications W1 L2 Uplift EPCM – End column caps F2 Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA H1 F1 F2 F1 3-3/4" W2 L1 Installation: • Use all specified fasteners. See Product Notes, page 18. • PCM 16 gauge post caps should not be substituted for PCM 12 gauge post caps unless approved by the Engineer of Record.
Fastener Schedule2 Dimensions (in) MiTek USP Stock No. Ref. No. Steel Gauge Beam Post Post Beam DF/SP Allowable Loads (Lbs.) Uplift1 W1 W2 H1 L1 L2 F1 F2 Qty Type Qty Type 160% 160% 160% Corrosion Finish Caps & Bases EPCM / PCM Post Caps Code Ref.
Caps & Bases PB / PBES / PBS Post Caps PB – Two-piece design Uplift PBES / PBS – Two-piece design with extended side plates and wrap around post design. Easy retrofit installations Uplift F1 F2 F2 F2 F1 Uplift F1 F1 F2 F2 F1 F2 F1 Materials: 18 gauge Finish: G90 galvanizing; PB44-6TZ & PB66-6TZ – G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18.
Caps & Bases PBC Post Beam Corner Connectors The PBC series is a one-piece connector designed to secure two mitered beams on a corner post while providing uplift capacity. Materials: 18 gauge Finish: G-185 galvanizing Codes: IBC, FL, LA Uplift F1 F2 Installation: • Use all specified fasteners. See Product Notes, page 18. • Install PBC on outside corner of post forming tabs to inner side of post. • Assumes beam members are bevel cut at corner.
Caps & Bases CPB Composite Post Bases The CPB is made of corrosion resistant composite material compatible with preservative treated lumber. Provides code required 1" stand-off and can be used with rough lumber sizes. Materials: High Strength composite Codes: IRC R317.1.4, IBC 2304.12.2.2, IRC R407.3, IBC 2304.10.7 Installation: • Attach base to post with (4) 10d HDG nails. • Attach post to concrete using 1/2" diameter rod into concrete and extend into wood member.
Caps & Bases KLCC Lally Column Caps Lally Column Caps connect lally columns to wood beams. Fits 3-1/2" and 4" diameter lally columns. Materials: 12 gauge Finish: Primer Installation: • Use all specified fasteners. See Product Notes, page 18. • Fit KLCC onto lally column. Position wood beam in KLCC saddle and fasten. Typical KLCC installation L H W KLCC MiTek USP Stock No. KLCC45-35 Fastener Schedule DF/SP Allowable 1,2,3,4 Loads (Lbs.) S-P-F Allowable 1,2,3,4 Loads (Lbs.
Caps & Bases KCCQ / KECCQ Column Caps Designed to be installed without the need to drill bolt holes, simplifying installation and maintaining the wood cross section. Installs with MiTek’s WS structural wood screws offering high uplift capacity. KCCQ – Standard column cap KECCQ – End column version Materials: See chart Finish: Primer Options: See chart for Corrosion Finish Options and Specialty Options on page 102.
Caps & Bases Fastener Schedule4 Dimensions (in) Beam MiTek USP Stock No. Ref. No. Column or Post DF/SP Allowable Loads (Lbs.)3 Bearing1 Uplift2,8 Steel Gauge W1 W2 H L Qty Type Qty Type 100% 160% Corrosion Finish KCCQ / KECCQ Column Caps Code Ref. Center Column Caps KCCQ71-4 CCQ7.1-4SDS2.5 3 7-1/4 3-5/8 6-1/2 11 16 WS3 14 WS3 48125 7065 KCCQ71-6 CCQ7.1-6SDS2.5 3 7-1/4 5-1/2 6-1/2 11 16 WS3 14 WS3 48125 7065 KCCQ71-71 CCQ7.1-7.1SDS2.
KCCQ / KECCQ Column Caps Caps & Bases Specialty Options: •K ECCQ – Straps may be rotated 90° with no reduction in published capacity on special orders where the W2 dimension is less than or equal to the W1 dimension. When W2 is greater than W1 uplift loads may be reduced, consult MiTek Engineering support. W1 L1 L H • KCCQO/KECCQO – Cap only, no strap design for field welding to pipe or other columns. H • KCCQOB – For + beam connections.
Caps & Bases KCC / KECC Column Caps KCC – Standard column cap. KECC – End column version. Materials: See chart Finish: Primer Options: See chart for Corrosion Finish Options. See page 105 for Specialty Options. All nominal lumber sizes are available for rough/full size lumber. Codes: IBC, FL, LA Typical KECC44 end cap installation Installation: • Use all specified fasteners. See Product Notes, page 18. • Bolt holes should be a minimum of 1/32" to a maximum of 1/16" larger than the bolt diameter.
Caps & Bases KCC / KECC Column Caps Dimensions (in) Caps & Bases MiTek USP Stock No.
Caps & Bases KCC / KECC Column Caps Refer to Options for Multiple-Beam Bolted Column Caps Special Order Worksheet for ordering instructions at MiTek-US.com on KCC/KECC Column Caps web page. W1 L L1 L H1 H H2 H W1 W1 W2 Optional KECC rotated straps 90° KCCOB KCCO W1 4" Typ. W3 L H2 H3 H1 H2 H1 H2 L 4" Typ.
Angles & Straps Angles & Straps Angles 108-111, 113-115 112, 118-119 Header Hangers 118 Knee Braces 135 Lateral Joist Connectors 120 Ornamental Connectors 125 Straps 121-134 Stud Plate Ties 116-117 106 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc. All Rights Reserved Angles & Straps Clips pg.
Angles & Straps Copyright © 2020 MiTek Industries, Inc.
Angles & Straps A / AC / JA / MP Framing Angles MP – 18 gauge. Field adjustable from 45° to 180° (flat) Load direction A3 – 18 gauge. Eliminates toenailing and increases strength AC – 16 gauge. Features staggered nail patterns which reduces wood splitting and allows installation on both sides of the supported member JA – 14 or 16 gauge.
A / AC / JA / MP Framing Angles Angles & Straps Dimensions (in) MiTek USP Stock No. Ref. No. Fastener Schedule Header 3,4 Joist Steel Gauge W1 W2 L Qty Type Qty Type 18 1-7/16 1-7/16 2-3/4 4 10d x 1-1/2 4 10d x 1-1/2 S-P-F DF/SP 1,2 1,2 Allowable Loads (Lbs.) Allowable Loads (Lbs.
Angles & Straps MP / MPA / MPF Multi-Purpose Framing Angles 1-1/2" MP34 – Framing angle without tabs 1-7/16" MPA1 – Tabs enable two and three-way connections MP4F – Connects 2x framing with floor sheathing up to 5/8" 4-1/2" MP6F – Connects 3x framing with floor sheathing up to 3/4".
Angles & Straps MP / MPA / MPF Multi-Purpose Framing Angles Fastener Schedule 5,6 Header or Stud Joist or Plate Steel Installation MiTek USP 2,4 Qty Type Qty Type Stock No. Ref. No. Gauge Type Figure 1 MPA1 A35 18 Figure 2 Figure 3 MP34 A34 18 Figure 4 DF/SP S-P-F 1,3,4 1,3,4 Allowable Loads (Lbs.) Direction Allowable Loads (Lbs.
Angles & Straps RBC Roof Boundary Clip F1 Framing plate designed to connect roof blocking to a wall top plate. Up to 3/4" gap Materials: 20 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • Field adjustable from 0º to 45º. • Bend angle only once.
Angles & Straps ML Angles ML angles are multi-purpose angles that install easily with MiTek’s WS15 structural wood screws. The staggered fastener pattern allows for back-to-back installations. Materials: 12 gauge Finish: G-185 galvanizing Codes: IBC, FL, LA W F1 H Typical ML26-TZ installation Installation: • Use all specified fasteners. See Product Notes, page 18. • MiTek WS15 structural wood screws (1/4" dia. x 1-1/2" long) are not supplied with ML angles.
Angles & Straps B / BL Corner Braces These multi-purpose braces are designed to provide reinforcement for 90° wood-to-wood connections. Some model designs may vary from illustration shown Materials: 12 gauge Finish: G90 galvanizing L Installation: • Use all specified fasteners. See Product Notes, page 18. MiTek USP Stock No. B23 B24 BL3 BL4 BL6 BL8 B66 B88 Ref. No.
Angles & Straps ANJ Heavy Angles The ANJ44S is a 7 gauge heavy duty angle intended to securely attach a post and beam together. Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc F2 Materials: 7 gauge Finish: Hot-dip galvanized 4" Corrosion Finish Installation: • Install with (2) 1/2" x 2-1/2" HDG lag screws into each leg. Steel Ref. No. Gauge W -7 3-1/2 H 4 L 4 1 DF/SP Allowable Loads (Lbs.
Angles & Straps RSPT / SPT / TSP Stud Plate Ties RSPT – 18 or 20 gauge SPT – 20 gauge TSP – 16 gauge. Optional diamond holes for various uplift capacities with Min and Max nailing configurations Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA Uplift F1 Uplift F4 Typical RSPT6-2 installation Installation: • Use all specified fasteners. See Product Notes, page 18. • T SP Min Nailing – Fill all round holes.
Angles & Straps SPT / SPTH / SPTHW Stud Plate Ties SPT – 20 gauge. Ties single and double plates to studs SPTH – Heavier 18 gauge version of SPT SPTHW – 18 gauge. Attaches plate to studs over 1/2" sheathing Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. Typical SPTWH installation H H H W Fastener Schedule2 Copyright © 2020 MiTek Industries, Inc.
Angles & Straps SFC Framing Clips Framing clips replace end cripples under window sills. Materials: 16 gauge Finish: G90 galvanizing Uplift Installation: • Use all specified fasteners. See Product Notes, page 18. Dimensions (in) F1 Fastener Schedule Sill Stud 2 DF/SP 1 Allowable Loads (Lbs.) Typical SFC6 installation F1 Uplift MiTek USP Steel Code Stock No. Ref. No. Gauge W H D Qty Type Qty Type 100% 115% 125% 160% Ref.
Angles & Straps SDPT Strap Post Ties Connects 2x4 stair posts and 4x4 posts to deck rim joist or stair stringers. Materials: 14 gauge Finish: G-185 galvanizing 1-1/2" Installation: • Use all specified fasteners. See Product Notes, page 18. • Install units in pairs on 2x4 (SDPT5-TZ) or 4x4 (SDPT7-TZ) post. Space the connectors 5" apart from center to center on the post. Use through bolts to fasten connectors to rim joist or stringer. Do not use lag bolts. Fasten to post with specified nails (see chart).
Angles & Straps LJC / LJQ Lateral Joist Connectors The LJC-TZ and LJQ-TZ Lateral Joist Connectors transfer lateral loads at the top foundation to the floor joists. The fastening patterns meet I-joist manufacturer recommendations. LJC-TZ – fastens the top side of the sill plate to the underside of the floor joist preventing splitting of the bottom chord flanges, and can be installed after the floor system has been installed.
Angles & Straps HRS / HTP / KST / KSTI / LSTA / LSTI / MSTA / MSTC / ST Strap Ties HRS – 12 gauge, 1-3/8" or 3-1/4" wide strapping 2-1/16" W Some model designs may vary from illustration shown 1-1/2" LSTA – 20 or 18 gauge, light-capacity 1-1/4" wide strapping LSTI – 3-3/4" wide strap ties provide tension load path for truss top chords. The nail pattern accommodates open web trusses with double top chord 3-1/4" 1-1/2" 1-3/8" MSTC – 3" wide strapping.
HRS / HTP / KST / KSTI / LSTA / LSTI / MSTA / MSTC / ST Strap Ties Angles & Straps Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: See chart for code references MiTek USP Stock No.4 KST116 LSTA9 LSTA12 LSTA15 LSTA18 LSTA21 LSTA24 KST29 KST213 KST216 LSTA30 LSTA36 MSTA9 MSTA12 MSTA15 MSTA18 MSTA21 MSTA24 LSTI49 LSTI73 ST9 ST12 ST18 ST22 MSTA30 MSTA36 MSTA48 KST218 KST224 HTP37-TZ Ref. No.
Angles & Straps Fastener Schedule6,7 Dimensions (in) MiTek USP Stock No. HRS6 HRS8 HRS12 KST227 KST237 KST248 KSTI226 KSTI236 KSTI248 KSTI260 KSTI272 HRS416-TZ KST260 KST272 Steel Ref. No.
Angles & Straps KHST / KRPS / PS Strap Ties KRPS – Meets IBC, IRC, & L.A. City requirements for notched plates where pipes placed in partitions PS – Piling Straps connect wood pilings to floor girders.
Angles & Straps L / LH / T / TH Straps L / T – 14 gauge medium-capacity straps fasten with either nails or bolts L LH / TH – 7 gauge heavy-capacity bolt-on strap Materials: See chart Finish: G90 galvanizing; LH / TH – Primer; TH12-HDG – Hot-dip galvanized Options: See chart for Corrosion Finish Options. Available for special order in black primer coated finish. H W H W Installation: • Use all specified fasteners. See Product Notes, page 18. • Straps are not load rated. L T6 MiTek USP Stock No.
Angles & Straps CMST / CMSTC / RS Coiled Strapping Coiled strapping enables cut-to-length convenience for a variety of immediate job site needs. End length Optional nails (wood shrinkage may occur and cause strap to buckle outward) CMST – 3" wide strapping features diamond nail holes to provide nailing options and reduce wood splitting CMSTC – 3" wide strapping is designed for high load conditions.
Angles & Straps CMST / CMSTC / RS Coiled Strapping Rim Joist Installation MiTek USP Stock No. Ref. No. RS250 CS20 RS20-R CS20-R, CSHP20 Steel Coil Gauge Length 250' 20 RS200 -- RS100 CSHP18 RS18-R -- RS150 25' 200' 18 100' 25' CS16 150' 16 RS16-R RS14-100 CS16-R 25' CS14 100' 14 RS14-R CS14-R 25' Cut Length S-P-F / Hem Fir Fastener Schedule3,4 Min End Length Qty.
Angles & Straps MSTCB Pre-Bent Straps Minimum (2) 2x or 4x The MSTCB Pre-Bent Strap is designed to fasten vertical studs to a beam or ridge beam member below where the beam depth will not allow complete fastener attachments with a standard product. 3" Minimum (2) 2x or 4x Materials: 14 gauge Finish: G90 galvanizing Stud Stud fastening Fastening Minimum length 22" Installation: • Use all specified fasteners. See Product Notes, page 18.
Angles & Straps HFS Compression & Tension Straps The HFS Hardy Frame® Saddle is a 14 gauge steel channel intended to be used as a splice at locations where plumbing or other vertical penetrations destroy the structural integrity of a wall’s top plates. Materials: 14 gauge Finish: G60 galvanizing Codes: IBC, FL, LA Typical HFS installation to underside of double top plates. Installation: • Use all specified fasteners. See Product Notes, page 18.
Angles & Straps HTW / KTS / LFTA / LTW / MTW Twist Straps Twist straps tie framing members to resist tension forces.
Angles & Straps HTW / KTS / LFTA / LTW / MTW Twist Straps MiTek USP 4 Stock No. Steel Ref. No. Gauge LTW12 LTS12 LTW16 LTS16 L L1 L2 18 1-1/4 12 4-1/2 4-1/2 18 1-1/4 16 6-1/2 6-1/2 Qty 12 Type 10d x 1-1/2 12 10d 12 10d x 1-1/2 12 10d 12 10d x 1-1/2 12 10d 12 10d x 1-1/2 12 10d 1 Uplift 160% S-P-F 1 Allowable Loads (Lbs.
Angles & Straps MSTAM / MSTCM Masonry Straps The MSTAM and MSTCM Strap Ties are designed to connect a wood structure above to a masonry wall below. Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: FL Installation: • Use all specified fasteners. See Product Notes, page 18. 5/8" 1-1/2" 1-1/2" L 3" minimum L 3" minimum 12-1/2" minimum 3" 3" 14" minimum W MSTCM40 Fastener Schedule Dimensions (in) Ref. No.
Angles & Straps HTWM Masonry Twist Straps The HTWM Twist Straps are designed for truss to concrete or masonry connections. Offers uplift resistance with variable heel height and positioning applications. W Materials: 14 gauge Finish: G90 galvanizing Codes: FL L1 L Installation: • Use all specified fasteners. See Product Notes, page 18. • Strap may be attached to either side of grouted masonry or concrete wall with a minimum of (1) #5 horizontal rebar.
Angles & Straps KHSA / KSA Connector Straps KSA – 12 gauge seismic horizontal tension tie Connector strap KHSA – 3 gauge. Designed for installation with bolts only Materials: See chart Finish: KSA – G90 galvanizing; KHSA – Primer Codes: IBC, FL, LA O Allowable loads 0 18° max D1 15° max D2 Hanger Installation: • Use all specified fasteners. See Product Notes, page 18. • KSA36 can be field adjusted for smaller beam widths.
Angles & Straps KVB / KVBI Knee Braces KVB – Installs with MiTek’s WS3 structural wood screws for higher load capacity. It can be retrofit into existing framing KVBI – Installs with common nails. Designed to be used with I-Joist purlins L Materials: 12 gauge Finish: G90 galvanizing Codes: IBC, FL, LA 2" Installation: • Use all specified fasteners. See Product Notes, page 18. • MiTek’s WS3 structural wood screws are included with KVB shipments.
Lumber Hangers Lumber Hangers Face Mount Hangers Hanger Selection Guide Masonry Hangers Panel & Purlin Hangers Slope/Skew Hangers Strap Hangers Top Mount Hangers Fire Wall Hangers Top Mount Fire Wall Hangers Face Mount Fire Wall Hangers Adjustable Connectors EWP Hanger Selector Guide EWP Installation Face Mount Hangers Top Mount Hangers Slope/Skew Hangers Glulam Beam Connectors Face Mount Hangers Hinge Connectors Seismic Straps Top Mount Hangers 136 139-165, 181-184 138 185-193 177-181 173-176 172 166-
Lumber Hangers Lumber Hangers Copyright © 2020 MiTek Industries, Inc.
Lumber Hangers JL Face Mount • • • • CSH 18 • • • • • JLIF 18 • • • SUH 16 • • • • • • • • • • • • • HD 14 • 14 • DTB 14 • • • • HDQIF 14 • • • • FWH 14 • • • • FWHBP 12 • • • 12 • FWHH 12 • • • • • 18 • • 18 • • KLB 14 • • • • • • HL Stringer Floor Truss 4x Glulam 315 - 330 184 -- 675 - 2,420 140, 142-150, 154-162 -- 890 181 -- 1,285 - 1,710 140, 142-143, 154-155 -- 465 - 1,520 139, 142-143, 154-155 -- 500
Lumber Hangers JL / JLIF / SUH Face Mount Joist Hangers MiTek offers a wide variety of light-gauge face mount joist hangers to accommodate application and installation preferences. JL series – 20 gauge, 2x dimensional joist hangers JLIF series – 18 gauge, 2x dimensional joist hangers.
Lumber Hangers HUS / JUS / MUS Slant Nail Face Mount Joist Hangers The HUS, JUS and MUS hanger series offers double shear nailing. MiTek’s dimple allows for 30° to 45° nailing through the joist into the header resulting in higher loads and less nailing. Slant nailing allows for higher load values, fewer nails, and faster installation. Materials: JUS – 18 gauge; MUS – 18 gauge; HUS – 14 or 16 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options. See HUS Specialty Options Chart.
Lumber Hangers HD Heavy-Duty Face Mount Hangers HD hangers are heavy-duty face mount hangers utilizing round and diamond holes to achieve design flexibility and maximum loads for use with headers, joists, and trusses. Materials: 14 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options. All nominal lumber sizes are available rough/full size lumber.
Fastener Schedule3 Dimensions (in) Joist Size MiTek USP Stock No. Steel Ref. No.
Fastener Schedule3 Dimensions (in) Joist Size Copyright © 2020 MiTek Industries, Inc.
Fastener Schedule3,4 Dimensions (in) Joist Size (2) 2 x 4 (2) 2 x 6 MiTek USP Stock No. JUS24-2 Ref. No.
Fastener Schedule3,4 Dimensions (in) Joist Size (2) 2 x 12 (2) 2 x 14 3-1/8 8-9/16 2 Uplift1 HUS210-2 HUS210-2 14 3-1/8 9-1/8 2 1 -- 8 16d 8 16d 2170 2465 2660 HUS210-2IF HUSC210-2 14 3-1/8 9-1/8 2 1 -- 8 16d 8 16d 2170 2465 2660 2420 Min 14 2155 2430 2610 1170 Max 20 Min 14 Max 20 14 3-1/8 9 2-1/2 A 1 Min/ Max -- Qty 8 1-1/8 -- 16 1-1/8 Type 16d 10d 16d 16d 16d Qty 6 Type 16d 6 10d 6 10 6 10d 2000 2245 2420 2350 2670 2880 2420 3080 3475 372
Fastener Schedule3,4 Dimensions (in) Joist Size MiTek USP Stock No. JUS36 3x6 3x8 3 x 10 SUH36 Ref. No. LUS36 U36 Steel Gauge W H D 18 2-9/16 5-1/4 2 16 2-9/16 5-5/16 Header DF/SP Allowable Loads (Lbs.
Fastener Schedule3,4 Dimensions (in) Joist Size 3 x 16 (2) 3 x 8 MiTek USP Stock No. Ref. No.
Fastener Schedule 3,4 Dimensions (in) Joist Size MiTek USP Stock No.
Fastener Schedule3,4 Dimensions (in) Joist Size MiTek USP Stock No. JUS46 LUS46 SUH46 4x6 4x8 U46 H D 18 3-5/8 5 2 16 3-9/16 4-13/16 2 Floor A Min/ Max Qty Type Qty 1 -- 4 16d 4 1-1/8 -- DF/SP Allowable Loads (Lbs.
Fastener Schedule3,4 Dimensions (in) Joist Size MiTek USP Stock No. JUS410 Steel Gauge 18 Ref. No. LUS410 W 3-5/8 H 8-7/8 D 2 SUH410 U410 16 3-9/16 8-3/8 HUS410 HUS410 14 3-5/8 HUS410IF HUSC410 14 3-5/8 HD410 4 x 12 HU410 Lumber Hangers DF/SP Allowable Loads (Lbs.
Fastener Schedule3 Dimensions (in) Joist Size MiTek USP Stock No. HD414 HU414 HD414IF 4 x 18 Ref. No.
Fastener Schedule2,3 Dimensions (in) Joist Size MiTek USP Stock No. Ref. No.
Lumber Hangers Face Mount Hangers – DF/SP Allowable Loads Fastener Schedule2 Dimensions (in) Joist Size MiTek USP Stock No. HD810 Ref. No.
Fastener Schedule3 Dimensions (in) Joist Size 2x4 D A 20 1-9/16 3 1-1/2 15/16 -- 4 18 1-9/16 3-1/8 1-1/2 -- -- 4 18 1-9/16 3-1/8 1-3/4 1 -- 4 JL24 LU24 -- JUS24 LUS24 SUH24 U24 16 1-9/16 3-1/4 2 1-3/16 HD26 HU26 14 1-9/16 3-1/2 2-1/2 1-1/8 -Min Max Qty 4 4 JL26 LU26 20 1-9/16 4-3/4 1-1/2 15/16 -- 6 JL26IF-TZ LUC26Z 18 1-9/16 4-1/2 1-1/2 -- -- 6 JUS26 LUS26 18 1-9/16 4-13/16 1-3/4 1 -- 4 MUS26 MUS26 18 1-9/16 5-1/16 2 1 -- 6 SU
Fastener Schedule3 Dimensions (in) Joist Size MiTek USP Stock No. W H D A Min/ Max Qty LU28 20 1-9/16 6-3/8 1-1/2 15/16 -- 10 -- 18 1-9/16 6-1/8 1-1/2 -- -- 8 JL210 LU210 20 1-9/16 8-1/4 1-1/2 15/16 -- 14 JL210IF-TZ LUC210Z 18 1-9/16 8-1/4 1-1/2 -- -- 11 Ref. No.
Fastener Schedule3,4 Dimensions (in) Joist Size (2) 2 x 4 (2) 2 x 6 MiTek USP Stock No. JUS24-2 Ref. No.
Fastener Schedule3,4 Dimensions (in) Joist Size (2) 2 x 12 8-9/16 2 1-1/8 -- 16 HUS210-2 14 3-1/8 9-1/8 2 1 -- 8 16d 8 16d 1905 2170 2340 HUS210-2IF HUSC210-2 14 3-1/8 9-1/8 2 1 -- 8 16d 8 16d 1905 2170 2340 1945 Min 14 1895 2140 2295 1030 Max 20 Min 14 Max 20 14 3-1/8 9 2-1/2 1-1/8 Type 16d 10d 16d 16d Qty 6 Type 16d 6 10d 6 10 6 10d 100% 115% 125% 160% 1625 1850 1925 1875 1760 1975 2130 2070 2345 2535 975 1945 2710 3055 3195 1715 1895 2140 2295
Fastener Schedule3,4 Dimensions (in) Joist Size MiTek USP Stock No. JUS36 3x6 3x8 3 x 10 SUH36 Ref. No. LUS36 U36 Header W H D A Min/ Max Qty Type Qty Type 18 2-9/16 5-1/4 2 1 -- 4 16d 4 16d 16 2-9/16 5-5/16 SPF Allowable Loads (Lbs.
Fastener Schedule3,4 Dimensions (in) Joist Size 3 x 16 MiTek USP Stock No. W H D A Min/ Max 2 1-1/8 -- SUH314 U314 16 2-9/16 10-9/16 HD314 HU314 14 2-9/16 11-5/16 2-1/2 1-1/8 HD314IF HUC314 14 2-9/16 11-5/16 2-1/2 HD316 HU316 14 2-9/16 13-5/16 2-1/2 1-1/8 HD316IF (2) 3 x 8 Ref. No.
Fastener Schedule3,4 Dimensions (in) Joist Size MiTek USP Stock No. JUS210-3 (3) 2 x 12 (3) 2 x 14 Ref. No.
Fastener Schedule3,4 Dimensions (in) Joist Size MiTek USP Stock No. JUS46 4x6 4x8 LUS46 H D 18 3-5/8 5 2 16 SPF Allowable Loads (Lbs.
Fastener Schedule3,4 Dimensions (in) Joist Size 4 x 12 MiTek USP Stock No. JUS410 Steel Gauge 18 Ref. No.
Fastener Schedule3 Dimensions (in) Joist Size MiTek USP Stock No. HD414 HU414 HD414IF 4 x 18 Ref. No.
Fastener Schedule3 Dimensions (in) Joist Size MiTek USP Stock No. Ref. No.
Lumber Hangers Face Mount Hangers – SPF Allowable Loads Fastener Schedule2 Dimensions (in) Joist Size MiTek USP Stock No. Ref. No.
HL Light Gauge Purlin Hangers Lumber Hangers TF These top mount hangers are designed for supporting floor joists or 2x dimensional lumber. The top mount style allows builders to drop in joists or purlins quickly. Materials: 18 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18.
HDO Heavy-Duty Top Mount Hangers Lumber Hangers Primarily used to hang joists or headers in medium load conditions. These hangers provide higher load values with less nailing. 1-1/4" TF Materials: 12 gauge Finish: G90 galvanizing Options: All nominal lumber sizes are available for rough/full size lumber. See Specialty Options Chart. Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • Check top flange dimensions to ensure compatibility with header widths.
Lumber Hangers KHW / SW / SWH Welded Top Flange Hangers SW – Light-duty hanger SWH – Medium-duty hanger KHW – Heavy-duty hanger installs with NA20D nails for higher load capacities Materials: SW top flange - 12 gauge; stirrup - 12 gauge; SWH top flange - 7 gauge; stirrup - 12 gauge; KHW top flange - 3 gauge; stirrup - 10 gauge Finish: Primer Options: All nominal lumber sizes are available for rough/ full size lumber. See Specialty Options below.
Fastener Schedule4 Dimensions (in) Header Beam/ Joist Size 2x4 2x6 2x8 2 x 10 2 x 12 2 x 14 MiTek Stock No.
Lumber Hangers Top Mount Hanger Charts Fastener Schedule4 Dimensions (in) Header Beam/ Joist Size (2) 2 x 10 (2) 2 x 12 (2) 2 x 14 (2) 2 x 16 4x4 4x6 4x8 4 x 10 Lumber Hangers H D L TF Top Face Uplift1 Roof Type Qty Type 100% 115% 125% 160% WP210-2 7/12 3-1/8 9-1/8 2-1/2 7 2-1/2 2 -- 16d 2 10d 3305 3305 3305 135 HDO210-2 HU210-2TF, HUS210-2TF 12 3-1/8 9-1/8 2-1/4 -- 2-1/2 4 10 16d 6 10d 4575 4575 4575 1275 HDO210-2IF HUC210-2TF, HUSC210-2TF 12 3-1
Top Mount Hanger Charts Lumber Hangers Fastener Schedule5 Dimensions (in) Header Beam/ Joist Size MiTek Stock No. Qty Ref. No. Steel Gauge W H D L TF DF/SP Allowable Loads (Lbs.
Lumber Hangers JH Multi-Purpose Strap Hanger These strap-style hangers are designed to support trusses, joists, or purlins. JH models may be bent along the flange allowing builders to use the hangers in top mount, face mount, or combination applications. Materials: 18 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18.
Lumber Hangers RR Ridge Rafter Hanger The RR Ridge Rafter supports rafter pitches up to 7:12 (30°). Nesting top flange for back-to-back installation on 2x support beams. Materials: 18 gauge Finish: G90 galvanizing Uplift Installation: • Use all specified fasteners. See Product Notes, page 18. • The rafter end at the ridge must be plumb cut to achieve published loads. • Optional diamond nail holes can be used to fasten RR to end of rafter before setting rafter into place.
Lumber Hangers LSSH Slope/Skew Hangers The LSSH series connects rafters to ridge beams in vaulted roof structures. This series is field adjustable to meet a variety of skew and/or slope applications. Slopes and skews 0° to 45°. W2 W1 W2 Materials: See chart Finish: G-185 galvanizing Options: See Chart for Corrosion Finish Options Codes: IBC, FL, LA LSSH15-TZ = 5-1/16" All other sizes = 8-7/8" Installation: • Use all specified fasteners. See Product Notes, page 18. 3" Steps: 1.
Lumber Hangers SKH / SKHH Skewed 45° Hangers SKH – Standard 45° skew hanger allows for a 40° to 50° skew range, without hanger modification SKHH – For heavier applications Materials: 14 or 16 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: See chart for code references SKH26L left skew SKH26R right skew D Installation: • Use all specified fasteners. See Product Notes, page 18. • The hangers listed are for standard sizes and will accommodate a 40° to 50° skew range.
Lumber Hangers SKH / SKHH Skewed 45° Hangers D D H H W Typical SKH2520R-2 staggered I-Joist installation right skew Fastener Schedule2 Dimensions (in) Beam/Joist Size Joist DF/SP Allowable Loads (Lbs.) Floor Ref. No. Ga. W H D Qty Type Qty Type Roof S-P-F Allowable Loads (Lbs.
Lumber Hangers KF / PHG Panel Hangers KF – Fastens to joist ends quickly with nails TF PHG – Features a gripper design to hold the joist in place with out nailing during the assembly process Locator windows Materials: 18 gauge Finish: G90 galvanizing Codes: IBC, FL, LA H D W Installation: • Use all specified fasteners. See Product Notes, page 18. • In panelized construction, installers are allowed to nail through both the sheathing and the hanger top flange with (1) 10d nail.
Lumber Hangers JPF Purlin Hangers Materials: 20 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • Diamond holes allow optional header nailing. • Joist nails must be driven at a 30° to 45° angle through the purlin into the header to achieve listed loads. Slant/double shear nails must be used to achieve listed load values. • 16d sinkers (0.148" dia.
Lumber Hangers JDS Purlin Hangers Materials: 18 gauge Finish: G90 galvanizing Codes: See chart for code references Top opening of starburst prong provides a witness hole Installation: • Use all specified fasteners. See Product Notes, page 18. • Joist nails must be driven at a 30° to 45° angle through the purlin into the header to achieve listed loads. Slant/double shear nails must be used to achieve listed load values.
Lumber Hangers TUS / DTUS Undersaddle Hangers TUS – For a single-ply purlin Uplift DTUS – For a single-ply purlin with a 2-ply saddle dimension F2 F2 Materials: 20 gauge Finish: G90 galvanizing Patents: U.S. Patent No. 8,966,857 B2 F2 Installation: • Use all specified fasteners. See Product Notes, page 18. • Attaches with standard 1-1/2" joist hanger nails that can be installed with a positive placement nail gun or be hand driven.
Lumber Hangers FHD Panel Hangers 3-3/4" The FHD26 hanger straddles the header and receives a joist from both sides. 3-1/8" Materials: 18 gauge Finish: G90 galvanizing H Installation: • Use all specified fasteners. See Product Notes, page 18. • In panelized construction, installers are allowed to nail through both the sheathing and the hanger top flange with (1) 10d nail. The nail should be centered in the top flange and be no closer than 1/4" from the back or front edge of the top flange.
Lumber Hangers ADTT-TZ Adjustable Deck Tension Tie Deck collapses are often caused by failure of the connection where the deck is attached to the main structure due to little or no lateral capacity. ADTT-TZ is an Adjustable Deck Tension Tie designed to effectively transfer the out of plane lateral loads of the deck to the house structure.
Lumber Hangers DTB Deck Tie Back The DTB-TZ Deck Tie Back provides positive anchorage between the deck framing and the exterior wall with a load carrying capacity that exceeds building code requirements. When used in conjunction with MiTek’s triple-zinc or gold-coat joist hangers, the DTB-TZ transfers the lateral loads into the exterior wall while the joist hangers support the vertical loads. The DTB-TZ can also be used to reinforce the connection between the rail post and the deck.
Lumber Hangers ERB / FB / FRB Fence Brackets ERB24 – Designed to mount prefabricated fence sections and works with 2x4 horizontal section rails. 3/4" FB26 – Secures 2x6 rails to wood posts. W FRB24 – Secures continuous 2x4 rails to wood posts. Pre-punched holes allow installers to splice 2x4 rail ends within the bracket. H H W Materials: See chart Finish: G-185 galvanizing Typical ERB24-TZ installation Typical FB24-TZ installation ERB24-TZ FB24-TZ Installation: • Use all specified fasteners.
Lumber Hangers UMH Universal Masonry Hangers A versatile solution for hanging beams from masonry walls. Face mount design allows hanger to be used with beam heights from 16" to 24". Available in a variety of widths for solid sawn, glulam, or engineered lumber beams. Materials: 3 gauge Finish: Primer Codes: FL 5-1/4" min edge distance Bond beam with (1) #5 rebar continuous 15-1/2" (2) 3/4" x 5" concrete screws (see footnote 2) Installation: • Use all specified fasteners. See Product Notes, page 18.
Lumber Hangers HD Masonry Face Mount Hangers The HD series Face Mount hangers can be used to connect roof framing members, trusses, and floor joists to masonry walls. Materials: 14 gauge Finish: G90 galvanizing Installation: • Masonry screws shall be Powers® Tapper+® HWH 3/16" x 1-3/4". 2" min 2" min 8" min 8" min Typical HD field installation Typical HD edge installation (flush to edge only) HD28 HD210 DF/SP Allowable Load (Lbs.
LGUM / HGUM Masonry Girder Hangers Lumber Hangers A LGUM and HGUM Masonry Girder Hangers are high-capacity beam/ girder hangers designed for installation to masonry or concrete walls. The LGUM and HGUM hangers use MiTek’s WS structural wood screws (supplied) to attach the beam to hanger and screw anchors (supplied) to attach to the masonry or concrete wall. These hangers eliminate the need for constructing beam pockets.
MPH Masonry Hangers Lumber Hangers These hangers are designed to support standard lumber joists, I-Joists, or beams. Easy installation into concrete block walls makes the MPH an attractive alternative to fabricating seats in masonry (or attaching ledgers) to support joists or beams. Install with (2) 16d duplex nails in grouted cell L 3-3/4" Materials: 12 gauge Finish: Primer Options: All nominal lumber sizes are available for rough full size lumber. See Specialty Options Chart on page 189.
1-3/4 x 14 1-3/4 x 16 MPH1714 MPH1716 WMU1.81/14 WMU1.81/16 12 12 1-13/16 1-13/16 14 16 7 7 2 2 16d duplex 16d duplex 2 2 10d x 1-1/2 10d x 1-1/2 3000 3000 3040 3040 3065 3065 1) Masonry compressive strength shall be minimum 1500 psi. 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d duplex nails are 0.162" dia.
Lumber Hangers HWUH Heavy-Duty Welded Universal Hangers Versatile heavy-duty top flange hanger attaches to both wood and masonry. Unique design allows builders to use one style hanger on the job when the structure has a variety of support materials. 10" 3-1/2" Materials: Top Flange – 3 gauge; Stirrup – 7 gauge Finish: Primer Options: See Specialty Options Chart on page 191 3-1/2" H Installation: • Use all specified fasteners. See Product Notes, page 18.
(2) 2 x 16 HWUH216-2 -- 3-1/8 16 Masonry Wood Masonry 2 6 2 1/2" x 6" J-Bolt 10d 1/2" x 6" J-Bolt 4 3060 4615 3060 10d 3060 4615 3060 3060 4615 3060 1030 955 1030 1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted. Lumber Hangers 2) NAILS: 10d nails are 0.148" dia. x 3" long. HWUH Heavy-Duty Welded Universal Hangers Fastener Schedule Beam/ Joist Size MiTek USP Stock No. 4x6 Ref. No.
Lumber Hangers NFM Narrow Flange Masonry Hangers NFM – Standard design 5-1/2" NFM_U – High uplift design H Materials: Top Flange – 3/8" steel; U-strap – 7 gauge Finish: Primer Options: See Specialty Options Chart on page 193 Codes: See chart for code references Installation: • Use all specified fasteners. See Product Notes, page 18. • Designed for both concrete walls and grout-filled reinforced CMU walls. W Typical NFM installation Typical NFM_U installation Steel Gauge MiTek USP Stock No.
3) J-Bolt shall be cast-in-place and have a minimum 6" embedment and not less than 4" from the edge of concrete. 4) In addition to the J-Bolt, "U" models also require a 3/4" dia. ITW Ramset/Redhead Dyna Bolt sleeve anchor or equal with minimum 5" embedment depth installed in the face. Bolt shall be installed in accordance with installation specifications provided by ITW Ramset. 5) Bolts shall conform to ASTM A 307 or better. 6) NAILS: 10d nails are 0.148" dia.
FWH Fire Wall Hangers Fire Wall Hangers The Fire Wall Hanger is designed for attaching truss, I-joist, solid sawn lumber, or engineered wood floor framing members to double wall top plates or minimum 2-ply 2x solid sawn header fire rated wood frame walls. The advanced design allows the installation of the FWH before the 5/8" gypsum wallboard (drywall) is attached and permits the building project to be completely framed-up, and weather-tight before the gypsum wallboard sheathing work starts.
FWH Fire Wall Hangers Fire Wall Hangers Typical FWH solid sawn header installation Typical FWH stud wall with (2) layers of 5/8" gypsum wallboard installation Typical FWH stud wall installation Fastener / Allowable Load Table Fastener Schedule5 Installation Type Top Face Qty Qty Type Qty 6 Without 5/8" gypsum wallboard or structural sheathing 6 6 After (1) layer of 5/8" gypsum wallboard is installed 6 After (2) layers of 5/8" gypsum wallboard are installed 6 Two-sided after (2) layers of 5/8"
Fire Wall Hangers FWHBP Fire Wall Hangers for Beams and Purlins MiTek has expanded the FWH Fire Wall Hanger series to include the higher load carrying capacity FWHBP, the Fire Wall Hanger for Beams and Purlins. The FWHBP transfers the load into the supporting wall thru bearing on the top plates and directly attaching to the stud pack or post below.
Fire Wall Hangers FWHBP Fire Wall Hangers for Beams and Purlins 4 Dimensions (in) Joist Size MiTek USP Stock No. 3-1/2 x 11-7/8 FWHBP35118 H 11-7/8 3-1/2 x 14 FWHBP3514 13-15/16 3-1/2 x 16 FWHBP3516 3-1/2 x 18 FWHBP3518 3-1/2 x 20 FWHBP3520 19-15/16 3-1/2 x 22 FWHBP3522 21-15/16 3-1/2 x 24 FWHBP3524 23-15/16 5-1/4 x 11-7/8 FWHBP52118 11-7/8 5-1/4 x 14 FWHBP5214 13-15/16 5-1/4 x 16 FWHBP5216 Ref. Steel No. Gauge W1 W23 DF/SP Allowable Loads (Lbs.
Fire Wall Hangers FWHH Heavy-Duty Fire Wall Hangers The MiTek FWHH Heavy-Duty Fire Wall Hanger is designed to support beams and purlins at header locations. The higher capacity of the FWHH is achieved through top flange bearing along with added face and beam/purlin nailing. As with the FWH hanger, the advanced design allows you to install the hangers before the drywall is attached, allowing your project to be completely framed-up and weather-tight before the drywall sheathing shows up on site.
3-1/2 x 22 FWHH3522 21-15/16 3-1/2 x 24 FWHH3524 23-15/16 1) Uplift Loads have been increased 60% for wind or seismic loads; no further increase shall be permitted. 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long. Fire Wall Hangers FWHH Heavy-Duty Fire Wall Hangers Fastener Schedule3 Dimensions (in) Joist Header Joist Size (in) 5-1/4 x 9-1/4 MiTek Stock No. FWHH52925 Ref. Steel No.
Fire Wall Hangers FWHFM Fire Wall Hangers for Face Mount Applications The FWHFM hanger fastens to the wide face of a balloon framed SCL column thereby eliminating the additive perpendicular-to-grain bearing stresses in the wall top and bottom plates seen with platform framing. The advanced design allows you to install the hangers before the gypsum wallboard (drywall) is attached, allowing your project to be completely framed-up and weather-tight before the gypsum wallboard sheathing shows up on site.
Fire Wall Hangers FWHFM Fire Wall Hangers for Face Mount Applications 3 Dimensions (in) Fastener Schedule Joist Joist Size (in) 3-1/2 x 9-1/4 MiTek USP Stock No. FWHFM35925 Ref. Steel No.
EWP Hangers Wood I-Joist Installation to Wood Sloped I-Joists Use sloped seat hangers and beveled web stiffeners whenever the slope exceeds the following: 1/2:12 for seat bearing lengths of 2-1/2" or less; 3/8:12 for bearing lengths between 2-1/2" and 3-1/2"; and 1/4:12 for bearing lengths in excess of 3-1/2". Fasteners Install only the specified nails. The flanges of wood I-Joists may split if larger diameter nails or longer nails are installed. Do not install nails larger than 16d common wire nails (0.
FWH Fire Wall Hangers Fire Wall Hangers The Fire Wall Hanger is designed for attaching truss, I-joist, solid sawn lumber, or engineered wood floor framing members to double wall top plates or minimum 2-ply 2x solid sawn header fire rated wood frame walls. The advanced design allows the installation of the FWH before the 5/8" gypsum wallboard (drywall) is attached and permits the building project to be completely framed-up, and weather-tight before the gypsum wallboard sheathing work starts.
FWH Fire Wall Hangers Fire Wall Hangers Typical FWH solid sawn header installation Typical FWH stud wall with (2) layers of 5/8" gypsum wallboard installation Typical FWH stud wall installation Fastener / Allowable Load Table Fastener Schedule5 Installation Type Top Face Qty Qty Type Qty 6 Without 5/8" gypsum wallboard or structural sheathing 6 6 After (1) layer of 5/8" gypsum wallboard is installed 6 After (2) layers of 5/8" gypsum wallboard are installed 6 Two-sided after (2) layers of 5/8"
Fire Wall Hangers FWHBP Fire Wall Hangers for Beams and Purlins MiTek has expanded the FWH Fire Wall Hanger series to include the higher load carrying capacity FWHBP, the Fire Wall Hanger for Beams and Purlins. The FWHBP transfers the load into the supporting wall thru bearing on the top plates and directly attaching to the stud pack or post below.
Fire Wall Hangers FWHBP Fire Wall Hangers for Beams and Purlins 4 Dimensions (in) Joist Size MiTek USP Stock No. 3-1/2 x 11-7/8 FWHBP35118 H 11-7/8 3-1/2 x 14 FWHBP3514 13-15/16 3-1/2 x 16 FWHBP3516 3-1/2 x 18 FWHBP3518 3-1/2 x 20 FWHBP3520 19-15/16 3-1/2 x 22 FWHBP3522 21-15/16 3-1/2 x 24 FWHBP3524 23-15/16 5-1/4 x 11-7/8 FWHBP52118 11-7/8 5-1/4 x 14 FWHBP5214 13-15/16 5-1/4 x 16 FWHBP5216 Ref. Steel No. Gauge W1 W23 DF/SP Allowable Loads (Lbs.
Fire Wall Hangers FWHH Heavy-Duty Fire Wall Hangers The MiTek FWHH Heavy-Duty Fire Wall Hanger is designed to support beams and purlins at header locations. The higher capacity of the FWHH is achieved through top flange bearing along with added face and beam/purlin nailing. As with the FWH hanger, the advanced design allows you to install the hangers before the drywall is attached, allowing your project to be completely framed-up and weather-tight before the drywall sheathing shows up on site.
3-1/2 x 22 FWHH3522 21-15/16 3-1/2 x 24 FWHH3524 23-15/16 1) Uplift Loads have been increased 60% for wind or seismic loads; no further increase shall be permitted. 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long. Fire Wall Hangers FWHH Heavy-Duty Fire Wall Hangers Fastener Schedule3 Dimensions (in) Joist Header Joist Size (in) 5-1/4 x 9-1/4 MiTek Stock No. FWHH52925 Ref. Steel No.
Fire Wall Hangers FWHFM Fire Wall Hangers for Face Mount Applications The FWHFM hanger fastens to the wide face of a balloon framed SCL column thereby eliminating the additive perpendicular-to-grain bearing stresses in the wall top and bottom plates seen with platform framing. The advanced design allows you to install the hangers before the gypsum wallboard (drywall) is attached, allowing your project to be completely framed-up and weather-tight before the gypsum wallboard sheathing shows up on site.
Fire Wall Hangers FWHFM Fire Wall Hangers for Face Mount Applications 3 Dimensions (in) Fastener Schedule Joist Joist Size (in) 3-1/2 x 9-1/4 MiTek USP Stock No. FWHFM35925 Ref. Steel No.
EWP Hangers Support Height & Lateral Stability Hangers for joists without web stiffeners must support the I-Joist’s top flange and provide lateral resistance with no less than 1⁄8" contact. be 60% of the joist height for stability during construction. If this cannot be accomplished, potential joist rotation must be resolved by other means.
Face Mount Top Mount Stringer Glulam Floor Truss 4x Truss (2x) I-Joist Beam/Joist/Rafter (rect shapes) Rim Joist Glulam Floor Truss 4x • • • • • • • • • • 960 - 1,680 960 - 1,680 205, 212 IHFL 18 • • 960 - 1,920 960 - 1,920 206, 211-213 • IHF 16 • HUS 16 • • Post • • Wall • 18 Nailer • THFI • • • • • HD 14 • • • HDQIF 14 • • • • • • • • • • • DF/SP 100% 1,890 - 3,190 207, 213 • 1,000 - 4,410 1,000 - 4,410 206, 211-213 • 2,760 - 5,58
EWP Hangers THFI Face Mount I-Joist Hangers The THFI is a face mount hanger designed to attach EWP I-joist members to wood headers. The unique design of the THFI combines the installation ease of a top mount hanger with the installation flexibility of a face mount hanger. Because the side flanges extend to the top chord of the I-joist, web stiffeners are not required.
EWP Hangers IHFL / IHF Face Mount I-Joist Hangers IHFL (18GA) and IHF (16GA) series face mount hangers feature speed prongs for temporary placement and seat cleats to grab the bottom flange of the supported I-joist. Diamond holes in header and joist allow for optional Max nailing for customized fastening to match allowable load needed.
EWP Hangers THF Face Mount I-Joist Hangers Designed to provide lateral support for the top chords of I-Joists in depths up to 16". Materials: See EWP Face Mount Hangers charts, page 217 Finish: G90 galvanizing Options: See Specialty Options chart Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • Web stiffeners are required for I-Joist installations.
EWP Hangers HD Face Mount Hangers Designed to support LVL, LSL, and PSL beams and headers in medium load conditions. Ma terials: See EWP Face Mount Hangers charts, pages 218-220 Finish: G90 galvanizing Options: See Specialty Options chart Codes: See chart for code references Installation: • Use all specified fasteners. See Product Notes, page 18. • Min Nailing – Fill all round nail holes. • Max Nailing – Fill all round and diamond nail holes.
EWP Hangers HDQIF Inverted Flange Face Mount Hangers Inverted flange face mount hangers fasten to LVL, LSL and PSL beams and headers with WS Wood Screws. A Ma terials: See EWP Face Mount Hangers charts, pages 218-220 Finish: G90 galvanizing Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • MiTek’s WS15 (1/4" dia. x 1-1/2" long) and WS3 (1/4" dia. x 3" long) structural wood screws are supplied with HDQIF hangers.
EWP Hangers THD / THDH Face Mount Hangers THD – Medium capacity hanger for LVL, LSL, and PSL beams THDH – Heavy capacity hanger for LVL, LSL, and PSL beams Materials: See EWP Face Mount Hangers charts, pages 218-220 Finish: G90 galvanizing Op tions: Rough/ Full sizes available for THD series. THD hangers with widths greater than 3" can have one flange inverted with no load reduction. Specify left (L) or (R) flange. See Specialty Options chart. Codes: IBC, FL, LA Installation: • Use all specified fasteners.
EWP Hangers I-Joist Charts Face Mount Hangers Fastener Schedule3 Dimensions (in) Joist Size (in) 1-1/2 x 9-1/4 - 9-1/2 1-1/2 x 11-1/4 - 11-7/8 MiTek USP Stock No. Ref. No. IHFL15925 IUS1.56/9.5 Web Stiff Reqd Ga -- 18 W H 1-1/2 9-1/16 D A 2-1/2 1-1/8 IHF15925 MIU1.56/9 -- 16 1-1/2 9-1/16 2-1/2 1-1/8 IHFL15112 IUS1.56/11.88 -- 18 1-1/2 11-1/16 2-1/2 1-1/8 IHF15112 MIU1.
EWP Hangers I-Joist Charts Face Mount Hangers Fastener Schedule3 Dimensions (in) Joist Size (in) MiTek USP Stock No. IHFL23112 2-5/16 x 11-7/8 Ref. No. IUS2.37/11.88 Web Stiff Reqd Ga -- W 18 2-5/16 H 11-3/16 D A 2-1/2 1-1/8 IHF23112 MIU2.37/11 -- 16 2-5/16 11-3/16 2-1/2 1-1/8 IHFL2314 IUS2.37/14 -- 18 2-5/16 13-1/2 2-1/2 1-1/8 IHF2314 MIU2.37/14 -- 16 2-5/16 13-1/2 2-1/2 1-1/8 IHFL2316 IUS2.37/16 -- 18 2-5/16 15-9/16 2-1/2 1-1/8 IHF2316 MIU2.
EWP Hangers I-Joist Charts Face Mount Hangers 3 Dimensions (in) Joist Size (in) MiTek USP Stock No. Ref. No. Web Stiff Reqd Ga Fastener Schedule 2 Header Joist W H D A 3-1/4 x 9-1/4 IHF16925-2 -- -- 16 3-3/8 9-1/16 2-1/2 1-1/8 3-1/4 x 11-1/4 IHF16112-2 -- -- 16 3-3/8 10-3/4 2-1/2 1-1/8 -- 18 3-1/2 8-5/8 2-1/2 1-1/8 3-1/2 x 9-1/4 - 9-1/2 IHFL35925 IUS3.56/9.5 IHF35925 MIU3.56/9 -- 16 3-1/2 8-5/8 2-1/2 1-1/8 IHFL35112 IUS3.56/11.
EWP Hangers SCL Charts Face Mount Hangers Fastener Schedule2,3 Dimensions (in) Joist Size (in) 1-3/4 x 5-1/2 MiTek USP Stock No. HUS175 Ref. No. HU1.81/5 HD1770 HU7 Header Web Stiff Reqd x Ga 16 W 1-13/16 H 5-3/8 x 14 1-13/16 7-1/8 D 3 A 2 Min/ Max Qty Type Qty -14 16d 6 Min -- x 16 1-13/16 7-1/8 x 14 1-13/16 9-1/8 3 2 -Min HD17925 HU9 1-3/4 x 9-1/2 Uplift1 Uplift1 Code 100% 115% 125% 160% 100% 115% 125% 160% Ref.
Fastener Schedule 2,3 Dimensions (in) Joist Size (in) MiTek USP Stock No. Ref. No. Header Web Stiff Reqd Ga W H x 14 2-3/4 13-3/16 D A Min/ Max Qty Type Qty Min 2-11/16 x 14 - 16 HD2714 HU2.75/14 -- x 12 2-3/4 12-1/4 HD410 -- x 14 3-9/16 8-13/16 4 2-1/2 -- 12 66 16d 16 14 DF/SP Header Allowable Loads (Lbs.) S-P-F Header Allowable Loads (Lbs.
EWP Hangers SCL Charts Face Mount Hangers Fastener Schedule2,3 Dimensions (in) Joist Size (in) MiTek USP Stock No. Ref. No. Web Stiff Reqd Ga Header W H D A -- x 14 5-3/8 9-7/8 HDQ5212IF THD612 THDH612 8 16d S-P-F Header Allowable Loads (Lbs.) 2465 2780 2980 1305 2165 2445 2620 1040 3695 4170 4470 2765 3250 3665 3930 2430 16d 24 12 HUCQ5.
EWP Hangers TFI / TFL / THO Top Mount Hangers TFI / THO – Engineered for I-Joist to header applications. Offers full lateral support of the I-Joist top chord, eliminating the need for web stiffeners in most applications. Raised dimple nailing guides help assure correct 45° nailing into the I-Joist bottom flange. The THO’s feature the patented Seat Cleat® that allows for quick, positive seating. The Seat Cleat® will hold the I-Joist in place, eliminating spring back during nailing in the bottom flange.
EWP Hangers BPH / HBPH Top Mount Hangers These hangers are used to support LVL, LSL, and PSL beams and headers in medium-to-heavy load conditions. Materials: BPH – 12 gauge; HBPH – 10 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • Refer to the top mount chart for applications requiring web stiffeners.
EWP Hangers HLBH Beam Hangers Heavy-duty hanger for LVL, LSL, and PSL beams. Materials: 7 gauge Finish: Primer Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • For welded installations, see page 325. • 16d ring shank nails are supplied with HLBH hangers. Typical HLBH installation Nailer Options – chart represents maximum allowable loads for hangers used on wood nailers. Reference page 203.
EWP Hangers PHM / PHXU Top Flange Hangers Used to connect LVL, LSL, and PSL beams to headers in medium load conditions using standard nails. L TF Materials: See EWP Top Mount Hangers charts, pages 221-229 Finish: Primer; PHXU – G90 galvanizing Codes: IBC, FL, LA Patents: U.S. Patent No. 6,463,711 B1 – PHXU H Installation: • Use all specified fasteners. See Product Notes, page 18. • For welded installations, see page 325.
EWP Hangers Top Mount Hanger Charts Joist Size (in) 1-1/2 x 9-1/4 1-1/2 x 9-1/2 1-1/2 x 11-1/4 1-1/2 x 11-7/8 Ref. No.
EWP Hangers Top Mount Hanger Charts Joist Size (in) Top Face Qty Qty Type Qty W H D L TF -- 18 2-1/8 16 2 -- 1-1/2 4 2 10d 2 10d x 1-1/2 1585 1585 1585 1260 1245 1585 130 TFL2395 ITS2.37/9.5 -- 18 2-5/16 9-1/2 2 -- 1-1/2 4 2 10d 2 10d x 1-1/2 1585 1585 1585 1260 1245 1585 130 TFL23118 ITS2.37/11.88 -- 18 2-5/16 11-7/8 2 -- 1-1/2 4 2 10d 2 10d x 1-1/2 1585 1585 1585 1260 1245 1585 130 TFL2314 ITS2.
EWP Hangers Copyright © 2020 MiTek Industries, Inc.
EWP Hangers Top Mount Hanger Charts Joist Size (in) MiTek USP Stock No. Ref. No. THO35112 BPH35112 3-1/2 x 11-1/4 HBPH35112 THO35118 ITS3.56/11.
EWP Hangers Top Mount Hanger Charts Joist Size (in) MiTek USP Stock No. TFI420 3-1/2 x 20 3-1/2 x 22 3-1/2 x 24 Ref. No. HIT420, MIT420 Copyright © 2020 MiTek Industries, Inc. All Rights Reserved 3-1/2 x 28 3-1/2 x 30 3-1/2 x 32 4 - 4-3/16 x 9-1/2 4 - 4-3/16 x 11-7/8 4 - 4-3/16 x 14 H D L TF Top Face Qty Qty Type Qty Type LVL PSL LSL Uplift2 DF DF/SP Code SPF I-Joist4 DF/SP 160% Ref.
EWP Hangers Top Mount Hanger Charts Joist Size (in) MiTek USP Stock No. BA4.12/16 x PHM4216 WP4.12 H=16 x 4-1/2 - 4-5/8 x 9-1/2 THO23950-2 MIT4.28/9.5, BA4.28/9.5 x PHM2395-2 WP4.28X H=9.5 x 4-1/2 - 4-5/8 x 11-7/8 THO23118-2 MIT4.28/11.88, BA4.28/11.88 x PHM23118-2 WP4.28X H=11.
EWP Hangers Top Mount Hanger Charts Joist Size (in) MiTek USP Stock No. HBPH55925 5-1/4 x 9-1/4 PHXU55925 HLBH55925 Ref. No. HB5.50/9.25 HWP5.37 H=9.25, HWPH5.37 H=9.25 HGLTV5.37 H=9.25 HBPH5595 5-1/4 x 11-1/4 5-1/4 x 11-1/2 5-1/4 x 12 Copyright © 2020 MiTek Industries, Inc.
EWP Hangers Top Mount Hanger Charts Fastener Schedule 5 Header Joist Dimensions (in) Joist Size (in) 5-1/4 x 20 7 x 7-1/4 7 x 9-1/4 MiTek USP Stock No. Type Qty Type LVL x 10 5-1/2 20 3-1/2 -- 3 6 16 16d 10 16d 6185 6185 6185 4910 -- 6185 2705 PHXU5520 HWPH5.37 H=20 x 7 5-1/2 20 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120 HLBH5520 HGLTV5.
EWP Hangers Top Mount Hanger Charts Joist Size MiTek USP (in) Stock No. Ref. No. BPH7118 HBPH7118 7 x 18 x -- x HWP7.12 H=18, HWPH7.
EWP Hangers TMP / TMPH Adjustable Rafter-To-Plate Connectors The TMP and TMPH are designed to make rafter-to-plate connections and eliminate time-consuming bird’s-mouth notching or bevel plate installation. Both series are available in I-Joists sizes, as well as standard 2x sizes.
EWP Hangers LSSH Slope/Skew Hangers W2 The LSSH series connects rafters to ridge beams in vaulted roof structures. This series is field adjustable to meet a variety of skew and/or slope applications. Slopes and skews 0° to 45°. W1 W2 Materials: See chart Finish: G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA LSSH15-TZ = 5-1/16" All other sizes = 8-7/8" Installation: • Use all specified fasteners. See Product Notes, page 18. Steps: 1.
Glulam Beam Connectors Glulam Beam Connectors LGU / MGU / HGU Girder Hangers LGU, MGU, and HGU’s are high capacity girder to girder face mount connectors. Fastens with MiTek’s WS structural wood screws for ease of installation. Fasteners are placed high on connector to permit the connection of a deep carried member to a shallower carrying member. Very useful where tops of beams must be flush.
Glulam Beam Connectors GHF Glulam Face Mount Hangers 2-1/8" Materials: See chart Finish: Primer Options: See Specialty Options Chart on page 234 H Installation: • Use all specified fasteners. See Product Notes, page 18. • MiTek’s WS structural wood screws are supplied with GHF hangers. Copyright © 2020 MiTek Industries, Inc.
Glulam Beam Connectors Specialty Options Chart – refer to Specialty Options pages 320-321 for additional details Skewed1,3 Option Sloped Seat 2 Sloped / Skewed 1,2 Inverted Flange 1˚ to 45˚ See Sloped Seat and Skewed Not available in widths less than 4-1/2" Allowable Loads 100% of table load. 75% of uplift load on skews greater than 15˚. 100% of table load 80% of table load 75% of uplift load on skews greater than 15˚. 100% of table load.
Glulam Beam Connectors KEG / KLEG / KMEG Bolted Glulam Beam Hangers TF L 4" KLEG – (4) bolt light-duty hanger. 3" 11-1/4" 3" KMEG – (6) bolt medium-duty hanger. H KEG – (8) bolt heavy-duty hanger. 3" 3" Materials: See chart Finish: Primer Options: See Specialty Options Chart Codes: IBC, FL, LA L TF 4" 8-1/4" H 3" 3" 3" D W Dimensions (in) Top Flange U-Strap Copyright © 2020 MiTek Industries, Inc. All Rights Reserved MiTek USP Stock No. Ref. No.
Glulam Beam Connectors Glulam Beam Connectors KGB / KHGB / KHHB Glulam Top Mount Hangers These hangers cover medium-to-heavy glulam beam and purlin applications. 2-1/2" KHHB – Medium capacity hanger KGB – Medium-to-heavy capacity hanger KHGB – Heavy capacity hanger H Materials: 7 gauge Finish: Primer Codes: IBC, FL, LA W Installation: • Use all specified fasteners. See Product Notes, page 18. • MiTek’s WS3 structural wood screws are supplied with hangers.
Glulam Beam Connectors KGLT / KHGLT Glulam Beam Hangers L KGLT – Medium capacity hanger L 2-1/2" 3-1/2" 2-1/2" 6-3/4" KHGLT – Heavy capacity hanger H Materials: See chart Finish: Primer Options: See Nailer Options chart below and Specialty Options Chart on page 238 Codes: IBC, FL, LA H 6" 5" W W Typical KGLT5 installation KGLT KHGLT Installation: • Use all specified fasteners. See Product Notes, page 18. • Beam height dimension (H) must be specified when ordering.
Glulam Beam Connectors Glulam Beam Connectors KGLT / KHGLT Glulam Beam Hangers Specialty Options Chart – refer to Specialty Options pages 320 and 322-323 for additional details Range Skewed1,3 1˚ to 50˚ Allowable Loads 50% of uplift load on skew greater than 15˚ Option Ordering Sloped Seat 1˚ to 45˚ 2,3 KGLT – 4,110-lb Max KHGLT – 7,000-lb Max Add SK , angle required, Add SL, slope required, right (R) or left (L) , and and up (U) or down (D), square cut (SQ) or to product number.
Glulam Beam Connectors KGLS / KGLST / KHGLS / KHGLST Glulam Saddle Hangers 4 Fastener Schedule Joist Header Supported Glulam Beam MiTek USP Size (in) Stock No. Ref. No. W KGLS35 GLS3-5 3-1/4 KGLST35 -- 3-1/4 KGLS37 GLS3-7 3-1/4 KGLST37 -- 3-1/4 KGLS39 GLS3-9 3-1/4 KGLST39 -- 3-1/4 KGLS55 GLS5-5 5-1/4 KGLST55 -- 5-1/4 KGLS57 GLS5-7 5-1/4 KGLST57 -- 5-1/4 3-1/8 5-1/8 KHGLS5 6-3/4 Copyright © 2020 MiTek Industries, Inc.
Glulam Beam Connectors Glulam Beam Connectors KHC Hinge Connectors Supports a glulam beam off of another glulam beam. Refer to the Optional Horizontal Loading Chart for design variations. PD F1 Materials: See chart Finish: Primer Codes: IBC, FL, LA PT 3" Installation: • Use all specified fasteners. See Product Notes, page 18. • To allow for wood shrinkage, position bolts in slots away from the bearing seat. • For dapped beams, reduce the “H” dimension by the “PT” dimension for each dap.
Glulam Beam Connectors KHC Hinge Connectors Glulam Beam Connectors Allowable Download Chart (2) Rotation Bolts3 Per Beam Dimensions (in) Beam Width (in) 5-1/8 6-3/4 8-3/4 10-3/4 MiTek Stock No. Suffix 55 56 57 59 75 76 77 79 95 96 97 99 115 116 117 119 Ref. No.
Truss & Rafter Truss & Rafter Truss & Rafter Angles Girder Tiedowns Hurricane Ties pg. 244-265 255-256 251-254, 257-259 256, 262-264 244 Strap Connector 265 Truss Anchors 244-250 Truss Structural Wood Screw 260-261 242 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Truss & Rafter Copyright © 2020 MiTek Industries, Inc.
Truss & Rafter NOP Moisture Barrier Plates Moisture Barrier Plates protect the bottom chords of trusses from moisture damage caused by direct contact with concrete. These plates eliminate the need for more expensive treated wood plates. W L Materials: See chart Finish: G90 galvanizing NOP1 Truss & Rafter Installation: • Use all specified fasteners. See Product Notes, page 18.
Truss & Rafter HLPTA Embedded Truss Anchor The HLPTA75 is designed and tested to provide higher lateral capacity and net uplift. Offers greater pullout resistance and is compatible with bond beam reinforcing. Concrete tie wall Tie beam reinforcing Materials: 18 gauge Finish: G90 galvanizing Codes: See chart for code references Patent: U.S. Patent No.
Truss & Rafter HTA / HHTA / HTAR Embedded Truss Anchors HTA – 16 or 18 gauge W Uplift HTAR – 16 or 18 gauge with attached moisture barrier F1 F2 HHTA – 14 gauge F2 F3 H Truss & Rafter Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options on page 247 Codes: FL Installation: • Use all specified fasteners. See Product Notes, page 18. • Embed 4" into concrete tie beam or masonry bond beam.
Truss & Rafter HTA / HHTA / HTAR Embedded Truss Anchors W W Uplift F3 H 4" Embedment 4" Embedment 1-1/2" HHTA20 HHTA16 Copyright © 2020 MiTek Industries, Inc. All Rights Reserved Ref. No.
Truss & Rafter DHTA Embedded Truss Anchors The DHTA embedded truss anchor series offer high uplift capacity with a two-strap design. The straps are attached to MiTek’s NOP style plate which ensures proper placement of straps while also providing a moisture barrier between the top of the wall and the truss. W Uplift F1 Truss & Rafter H F3 F2 Materials: DHTAxx-18 – 18 gauge; DHTAxx – 16 gauge Finish: G90 galvanizing Codes: FL 4" Embed Installation: • Use all specified fasteners.
Truss & Rafter DTC Embedded Truss Anchors The DTC series attaches trusses to concrete or masonry walls. Innovative seat design gives added lateral resistance while still providing a moisture barrier. Uplift F1 F2 F2 Materials: 16 gauge Finish: G90 galvanizing Codes: FL F1 Truss & Rafter Installation: • Use all specified fasteners. See Product Notes, page 18. • Embed 4" into concrete tie beam or masonry bond beam. • Installations should be spaced no closer together than 8" center-to-center.
Truss & Rafter TA / TAR Embedded Truss Anchors TA – Anchors are rated for both uplift and lateral loads. They can be installed straight or field-bent around truss or rafter members. An embossed embedment line assures accurate embedment depth. W TAR – Riveted anchors provide a moisture barrier in addition to uplift and lateral resistance all in one product. Uplift Truss & Rafter Materials: 14 gauge Finish: G90 galvanizing Installation: • Use all specified fasteners. See Product Notes, page 18.
Truss & Rafter RFUS Uplift Girder Ties The RFUS is a multi-purpose engineered solution for attaching trusses to concrete or masonry walls. Screw Anchor fastening eliminates mislocated cast-in-place anchor bolts and allows retrofit installations. Uplift Materials: 10 gauge Finish: Primer Codes: FL Fastener Schedule Rafter/Truss MiTek USP Steel Stock No. Ref. No. Gauge RFUS FGTR 10 No.
Truss & Rafter UGTS / USC Uplift Girder Ties UGTS – 2-screw anchor shorter design when space is limited Lintel Block with (1) #5 continuous rebar USC – 4-screw anchor high load design Truss & Rafter Materials: 10 gauge Finish: Primer Codes: FL Pitch 4/12 – 8/12 7-1/2 min edge distance 8" concrete block with minimum (1) #5 rebar each cell continuous to footing with standard hook at bolt locations 3/4" anchors. Use 2 or 4 as required for uplift Installation: • Use all specified fasteners.
Truss & Rafter LUGT Girder Tiedowns 6-3/4" The LUGT series is an adaptable tiedown for girder trusses and offers several installation options to accommodate different framing conditions. It is an ideal retrofit solution to reinforce truss connections to transfer high wind loads to supporting walls and can be used on either concrete or CMU block walls. Sizes available for 2-ply, 3-ply and 4-ply trusses.
Truss & Rafter MUGT15 Girder Tiedown Designed for higher uplift resistance for concrete block construction. The MUGT15 can accommodate variable truss bearing depths. Install a minimum of (12) 10d nails into back Install a minimum of (4) 10d nails into the top Truss & Rafter Materials: 12 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Installation: • Use all specified fasteners. See Product Notes, page 18. • When straps are wrapped over the truss, install nails in backside of truss.
Truss & Rafter HGAM Hurricane Gusset Angles Uplift Designed for attaching gable end trusses to wood top plates and masonry walls. F1 For installation into grouted concrete tie beam or masonry bond beam. Provides lateral and uplift resistance. F3 F1 F2 Embossed gussets improve lateral load resistance 3-1/2" Materials: 14 gauge Finish: G90 galvanizing Codes: FL Moisture barrier not shown Rafter/Truss Steel Gauge Qty Type2 Ref. No.
Truss & Rafter RTM Hurricane Retrofit Connector Designed as a retrofit connector for trusses installed on top plates. Can also be used as a holdown for a roof or floor system. 5" Uplift Materials: 18 gauge Finish: G90 galvanizing Codes: FL 1-9/16" F3 F1 3-1/2" F1 F2 Truss & Rafter 8-15/16" Installation: • Use all specified fasteners. See Product Notes, page 18. • Concrete screws are not supplied with RT16M connector.
Truss & Rafter LUGT Girder Tiedowns The LUGT series is an adaptable tiedown for girder trusses and offers several installation options to accommodate different framing conditions. It is an ideal retrofit solution to reinforce truss connections to transfer high wind loads to supporting walls. Sizes available for 1-ply, 2-ply, 3-ply and 4-ply trusses.
MUGT Girder Tiedown Truss & Rafter Designed for higher uplift resistance for wood frame construction. The MUGT15 can accommodate variable truss bearing depths. Install a minimum of (12) 10d nails into back Install a minimum of (4) 10d nails into the top Truss & Rafter Materials: 12 gauge Finish: G90 galvanizing Codes: IBC, FL, LA 14-5/8" Install a minimum of (6) 10d nails into the face Installation: • Use all specified fasteners. See Product Notes, page 18.
UGTQ Universal Girder Tiedown Truss & Rafter The Universal Girder Tiedown, UGTQ, is a high capacity tiedown designed to resist uplift loads on multi-ply roof trusses. The UGTQ installs with MiTek’s WS structural wood screws and is fastened on one side for single connector installations or opposite sides for two connector installations. The UGTQ is available in left and right models for installation near the end of girders.
Truss & Rafter WSTS Truss Structural Wood Screw The MiTek® Pro Series WSTS Truss Structural Wood Screw can be used to resist uplift and lateral loads for truss/rafter-to-plate and stud-to-plate connections. The WSTS is tested in accordance with ICC-ES AC233 and AC13 and meets 2018 IRC and IBC code requirements. Truss & Rafter TM Features and Benefits: • Reverse thread angle on opposite ends of screw creates increased withdrawal where it’s needed for higher capacity and greater uplift resistance.
Truss & Rafter WSTS Truss Structural Wood Screw 22° 15° 0° 1-3/4" +/– 1/4" 25° 2-3/4" 2-3/4" 3/4" +/– 1/4" 3/4" +/– 1/4" 25° 25° 22° 15° 0° 22° 15° 0° Typical WSTS6 truss between wall studs installation Typical WSTS6 double top plate-to-stud installation Typical WSTS6 top plate-to-end wall truss installation Typical WSTS45 stud-to-single bottom plate installation Typical WSTS45 stud-to-single bottom plate installation Figure 1A Figure 1B Figure 2 Figure 3 Figure 4 Figure 5 Specific
Truss & Rafter HC / HCPRS / HHCP / LFTA / RT / TSP Hurricane Ties These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.
Truss & Rafter HC / HCPRS / HHCP / LFTA / RT / TSP Hurricane Ties Materials: See chart Finish: G90 galvanizing; HHCP4-TZ – G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: S ee chart for code references MiTek Stock No. Steel Ref. No. Gauge Qty RT3A H3 4 DF/SP Allowable Loads (Lbs.)1 S-P-F Allowable Loads (Lbs.
Truss & Rafter HC / HCPRS / HHCP / LFTA / RT / TSP Hurricane Ties Uplift F3 F4 F1 Truss & Rafter F2 Typical RT3A truss/rafter to plate installation Typical RT4 truss/rafter to plate installation Typical RT5 truss/rafter to double plate installation Typical RT6 truss/rafter to plate installation Typical RT7 truss/rafter to double plate installation Uplift F3 F4 F1 F2 Typical RT7A truss/rafter to double plate installation Typical RT7AT 2x4 bottom chord installation Typical RT8A stud to double
Truss & Rafter RUSC Retrofit Strap Connector The RUSC Retro Uplift Strap Connector provides a wood-to-wood uplift connection attaching trusses with a 2x4 bottom chord to a double stud in the wall below. MiTek’s WS3 structural wood screws are utilized for fast installation. The connector can be installed after roof sheathing has been installed. Materials: 10 gauge Finish: Primer Codes: FL Installation: • Use all specified fasteners. See Product Notes, page 18. • The RUSC shall be installed in pairs.
Plated Truss Plated Truss Plated Truss pg. 268-295 Alternate Installations 287 Blocking Supports 294 Drag Strut Connectors 282 Face Mount Hangers Field Splice Kits 268-272 295 Girder Hangers 283-286 Hip/Jack Connectors 281-282 294 Skewed Nail Plate 280 Spacers/Braces 288-289 Strap Hangers 273-279 Supplementary Bearing Plates Truss Clips 266 290 291-294 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Plated Truss Copyright © 2020 MiTek Industries, Inc.
Plated Truss MUS / HUS Slant Nail Truss Hangers A The MUS / HUS hanger series offers double shear nailing. MiTek’s raiseddimple allows for 30° to 45° nailing through the joist into header, resulting in higher loads and less nailing.
Plated Truss THD Heavy-Duty Face Mount Truss Hangers A Medium-to-heavy capacity face mount hanger. Some THD models are available with a min/max installation option. Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA H Additional diamond holes for max nailing W Typical THD28 installation D THD210 Bend line nailing H Drive bend line nails into header at 45° to achieve listed loads.
Plated Truss THDH Heavy-Duty Truss Hangers Materials: 12 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options and page 271 for Specialty Options chart Codes: IBC, FL, LA Bend line nailing where applicable H Plated Truss D W Typical THDH installation MiTek USP Stock No. Drive bend line nails into header at 45° to achieve listed loads.
Fastener Schedule3 Dimensions (in) Truss2 Header MiTek USP Stock No. Floor Ref. No. W H D A Roof S-P-F Allowable Loads (Lbs.
Plated Truss THDHQ Girder Truss Hangers The THDHQ hangers are designed to attach multi-ply girder trusses together using MiTek’s WS structural wood screws for higher design load capacity. THDHQ hangers can also be used to attach structural composite lumber (SCL). A H Materials: 12 gauge Finish: G90 galvanizing Codes: IBC, FL, LA D Installation: • Use all specified fasteners. • MiTek’s WS structural wood screws are supplied with THDHQ hangers.
Plated Truss MSH Adjustable Strap Hangers A The MSH is field adjustable. The flanges can be used in top mount, face mount, or combination installations. An open back design allows installation after a member is placed in position. A A Materials: See chart Finish: G90 galvanizing Options: See chart for Corrosion Finish Options on pages 274-275 and Nailer Options Chart below Codes: IBC, FL, LA 23" 22" H H B Installation: • Use all specified fasteners. See Product Notes, page 18.
Plated Truss MSH Adjustable Strap Hangers MiTek USP Stock No. MSH29 MSH213 Ref. No.
Plated Truss MSH Adjustable Strap Hangers 2x Lumber or Trusses MiTek USP Stock No. MSH222 Ref. No. THAI222 MSH1713 -- Fastener Schedule2 Header Joist Dimensions (in) Steel Gauge Joist Material & Width W D H 18 1-5/8 1-3/4 23 A B Mounting Condition 1-13/16 10-13/16 18 1-13/16 1-3/4 14-7/16 1-13/16 10-3/4 1-3/4" LVL or I-Joist MSH1722 2" wide I-Joist 2-5/16" wide I-Joist MSH2322 MSH322 MSH413 MSH418 Copyright © 2020 MiTek Industries, Inc.
Plated Truss MSHL/R Skewed Truss Hangers The MSHL/R is a versatile 45° skewed hanger with multiple installation options. It can be installed on a supporting girder truss as well as solid-sawn and structural composite lumber headers. Materials: See chart Finish: G90 galvanizing Codes: See chart for code references Typical MSH213R installation Typical MSH213L installation Right skew Installation: • Install the required number of fasteners according to the load table.
Plated Truss MSSHL/R Severely Skewed Hangers MiTek’s MSSH217 hanger accommodates a skew range of 60° to 85° (30° maximum off the girder) without the need for a more expensive custom design hanger. Face nail to webs or bend the flange strap over the chord. Available in left (L) or right (R) configurations.
Plated Truss MSHA Adjustable Strap Skewed Hangers MiTek’s MSHA Series hanger offers the most flexible field solution for truss-to-truss connections accommodating a range of skews and challenging web-chord geometry often found in truss framing. Eliminating the need for special orders, the MSHA Series hanger provides economical solutions for 1-ply or 2-ply roof trusses and 1-ply floor trusses skewed between 22-1/2° to 75°.
MSHA Adjustable Strap Skewed Hangers Plated Truss Installation Sequence for Skews > 22½°: Align back edge of carried member with the slotted holes on the acute side Rotate acute side to desired angle Step 2: Utilizing a piece of scrap fastened to the hanger on the obtuse side, bend the hanger to the desired angle. Step 1: Install acute side top and/or face header nails. Fastener Schedule4 Dimensions (in) 2x Trusses MiTek USP Stock No. MSHA29L/R Ref. No.
Plated Truss SNP Skewed Nail Plate The SNP3 Skewed Nail Plate is designed for connecting square cut corner jack trusses at skews from 0° to 90°, as depicted in Figure 1 below. An alternate installation for front side attachment at skews 0° to 45° is depicted in Figure 2 below. 3-1/2" 3-1/2" Materials: 16 gauge Finish: G90 galvanizing Codes: See chart for code references Installation: • Bend angle only once. 3-3/8" • 8d common (0.131" dia. x 2-1/2" long) nails may be used in lieu of 8d (0.
Plated Truss HHC / HJC / HJHC / HTHJ Hip/Jack Connectors HHC – Designed to support hip/hip truss/rafter. Contact MiTek when using in multi-ply applications HJHC – Allows for hip/hip support and hip/jack/hip installations HJC / HTHJ – Used to simultaneously hang a combination of hips and jacks off girder trusses. These hangers fit both left-hand and right-hand applications.
Plated Truss BN Breakfast Nook Hangers Designed to carry four mono trusses in one connector, it reduces installation time and cost. Provides a tested, load rated connection. Standard configuration spacing: 22-1/2°, 45°, 45°, 45°, 22-1/2°. The design also includes field adjustable nailing tabs. 22-1/2° 22-1/2° Materials: 14 gauge Finish: Primer Codes: IBC, FL, LA 45° 45° Nailing tabs adjust to fasten 22-1/2° mono trusses 45° BN264 Standard configuration Installation: • Use all specified fasteners.
Plated Truss GTWS High Uplift Girder Truss Hangers The GTWS series girder-to-girder hangers feature high uplift capacities along with high gravity load ratings. Materials: 10 gauge Finish: G90 galvanizing Codes: FL Supported truss end vertical min 2x6 required. Ensure truss plate is installed flush bottom and min 3" in height (to resist end grain splitting) 16" Installation: • Use all specified fasteners. See Product Notes, page 18.
Plated Truss GT / GTD / GTS Girder Truss Hangers The GT primarily hangs girder trusses off other girder trusses, although a wide variety of other heavy-duty installations apply. L Materials: Back Plate – 3 gauge; Strap – 7 gauge Finish: Primer Options: All models available in LVL sizes, use M in place of T, as in GT2M4B Codes: See chart for code references H 9-1/4" Installation: • Use all specified fasteners. See Product Notes, page 18. • Minimum heel height is 9-1/4" for GT hangers.
Plated Truss GT / GTD / GTS Girder Truss Hangers H H W2 5-1/2" W1 GTS top view (left shown) 4-1/2" Fastener Schedule2,3,6 Ref. No. W1 W2 L H B Qty Bolt Dia.
Plated Truss GTQ / GTQM Girder Truss Hangers The GTQ / GTQM hangers connect to multi-ply girder truss with MiTek’s WS structural wood screws offering high load capacities. Design features minimum and maximum fastening installation options to accommodate various sizes of vertical web. GTQM’s are designed for LVL sizes, for example GTQM218. 18" Materials: 7 gauge Finish: G90 galvanizing 6-1/4" Plated Truss 4-1/2" W Installation: • Install all MiTek’s WS structural wood screws as specified.
Plated Truss Alternate Installations Backer block installation Wood blocking used to achieve full design load value of a face mount hanger attached to a carrying member. Blocking to be designed by truss designer or engineer of record. • Wood blocking should be of similar size/grade as the truss member to which it is attached. The blocking should be designed to act as one unit with truss members. • Truss designer shall approve blocking size/grade, fasteners required, and application.
Plated Truss Truss Brace & Spacer (Stabilizer™) The Stabilizer™ Truss Brace & Spacer provides temporary construction bracing in the roof and ceiling planes, as well as permanent lateral bracing for webs as specified by your truss engineering. 24 o.c. Odd spacing The Stabilizer™ is easily installed by embedding the patented MII 20 teeth on the top flange straight into the edge of the truss member to be braced with a framing hammer.
Plated Truss TS / TSX Truss Spacers Truss spacers give framers fast and accurate spacing for trusses, rafters, or floor joists. The TS and TSX eliminate the need to mark layouts on bearing plates, improve installation speed, and help eliminate spacing errors. These spacers are light weight and compact. Materials: See chart Finish: G90 galvanizing Installation: • Use (1) 8d nail per end to fasten units to trusses, rafters, or floor joists.
Plated Truss SBP Supplementary Bearing Plates Use the SBP instead of extra truss plies or nail-on scabs to distribute concentrated truss reactions and avoid top plate crushing. The two-piece design accommodates any number of girder plies. A wraparound design gives superior uplift resistance, and reinforcement ribs effectively distribute bearing loads. Works with both single and double 2x4 or 2x6 top plates.
Plated Truss FTC / FTCF Floor Truss Clips FTC clips slide easily onto the top or bottom chord and provides a guide to help position and support the second truss during assembly 4-3/8" FTCF clips easily install after the trusses are installed W2 Materials: 18 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Patents: U.S. Patent No. 5,653,079 H W1 1-1/8" 2" Installation: • Use all specified fasteners. See Product Notes, page 18.
Plated Truss VTT Valley Truss Tie VTT Valley Truss Tie is designed to transfer loads from a valley truss into the supporting structure below. It also resists the sliding forces from downward loads when the valley truss is set upon a sloped lower roof. The ability to resist the sliding force eliminates the need for support wedges under the valley truss bottom chord or special order valley roof trusses with a bevel-cut bottom chord.
Plated Truss STC Truss Clips The STC provides uplift resistance by securing trusses to top plates. Slotted nail holes allow for horizontal movement as scissor trusses deflect. 1-1/4" slots Materials: 12 gauge Finish: G90 galvanizing Codes: IBC, FL, LA Uplift F1 Installation: • Use all specified fasteners. See Product Notes, page 18. • When installing, do not fully set nails. • Locate nails into the center of slots to allow for horizontal movement.
Plated Truss HTC Heavy Truss Deflection Clip Slotted design allows truss to deflect without imposing load on wall below. F2 F2 Materials: 16 gauge Finish: G90 galvanizing Codes: IBC, FL, LA 3-1/4" Installation: • Use all specified fasteners. See Product Notes, page 18. • Do not fully set nails. Fastener Schedule Plate 1-15/16" DF/SP 1 Allowable Loads (Lbs.) Without Gap Type 10d x 1-1/2 HTC4 Typical HTC4 installation 5 Qty 3 1" 3-1/2" 4 Truss/ Rafter MiTek USP Steel Top Side Stock No. Ref.
Plated Truss FS / FSS Truss Field Splice Kits Job site splicing of long trusses is made easier with Truss Field Splice Kits. The FS and FSS (for scissors trusses) includes a pair of plates, bolts, nuts, and a Splice Clip for top chord alignment. Allowable loads are sometimes limited by tension in the net section of the wood. Choose the bottom chord size and species that will satisfy the tension requirement. Analyze tension in the web to determine the required size.
Deck & Fences Deck & Fences Deck & Fences Angles pg. 298-305 302 Deck Connectors 298-300, 302 Fence Hardware 303-305 296 301 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Deck & Fences Copyright © 2020 MiTek Industries, Inc.
Deck & Fences ADTT-TZ Adjustable Deck Tension Tie Deck collapses are often caused by failure of the connection where the deck is attached to the main structure due to little or no lateral capacity. ADTT-TZ is an Adjustable Deck Tension Tie designed to effectively transfer the out of plane lateral loads of the deck to the house structure. Features: • E xceeds “Hold-down Device” requirements per 2018 IRC, Section 507.9.2 [Figure R507.9.
Deck & Fences DTB Deck Tie Back Deck Tie Back reinforces the connection of rail posts to a deck. Also provides lateral strength of deck-to-ledger attachment by securing deck to house framing. 6" Materials: 14 gauge Finish: G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA IRC R507.1 CL Installation: • Use all specified fasteners. See Product Notes, page 18. • Install with MiTek’s THR 1/2" threaded rod or equivalent.
Deck & Fences CSH Concealed Stringer Hanger The CSH-TZ concealed stringer hanger provides a method of connecting a stair stringer with a hidden hanger. The seat of the hanger is adjustable to match the slope of the stair stringer. 1-7/16" 1-1/2" The reversible design allows the connector to be used on the left, right, or interior stringers. The CSH-TZ may be used with MiTek’s SCA Stair Angles for a complete, easy-to-use stair framing solution.
Deck & Fences SCA Stair Angles Stair angles simplify stair construction. There is no need to calculate and notch stair stringers. Stronger and safer than wood blocking, and the angle and fasteners are hidden from view. Materials: 12 gauge Finish: G-185 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA 1-3/8" MiTek USP Steel L Stock No. Ref. No. Gauge (in) Qty Type Typical SCA9-TZ installation 1-3/8" SCA9-TZ Typical SCA10-TZ installation DF/SP 1 Allowable Loads (Lbs.
Deck & Fences DC Deck Clip Connects deck boards to joists without face nails or screws. Eliminates rust stains on decks, as well as splintering or wood rot caused by screw or nail “craters”. The DC50-TZ works like tongue-in-groove flooring and is easy to install. Raised dimples on the clip provide consistent spacing between deck boards. Materials: 20 gauge Finish: G-185 galvanizing Options: See chart for Corrosion Finish Options 1) Use with 1-1/8" or thicker wood decking. 2) NAILS: 8d x 1-1/2 nails are 0.
Deck & Fences PRT Pipe Rail Ties PRT15-TZ – is for 1-5/8" vertical pipe posts (1-7/8" outside pipe diameter). Can be field bent 90° for outside corner installations. 2-1/2" PRT2-TZ / PRT2H-TZ – is for 2" vertical pipe posts (2-3/8" outside pipe diameter). Can be field bent 90° for outside corner installations. 6-3/8" 1-1/2" PRTIC2-TZ – is for inside corner installations. For 2" vertical pipe posts (2-3/8" outside pipe diameter).
Deck & Fences ERB / FB / FRB Fence Brackets ERB24 – Designed to mount prefabricated fence sections and works with 2x4 horizontal section rails 3/4" FB26 – Secures 2x6 rails to wood posts W FRB24 – Secures continuous 2x4 rails to wood posts.
Deck & Fences PCP Plastic Post Caps These seamless caps keep water off post tops, protecting wood from moisture damage. The PCP’s plastic construction is corrosion-proof and paintable. Not available in rough or full lumber sizes. Materials: Hi-impact plastic Finish: Gray color Post / Column MiTek USP 1 Stock No. Size 4x4 PCP44 6x6 PCP66 Dimension (in) Ref. No. DPPC4BK DPPC6BK Typical PCP44 installation Code Color Ref.
General Hardware General Hardware 314-315 Corner Tie 316 D.I.Y. Products 309 Drywall Clip 308 Insulation Supports 308 Mending Plates 317 Nail Plates 317 Plywood Clips 308 Protection Plates 310 Shelf Brackets 316 Straps 311-312 Stud Shoes 312 Wall Bracing 313 Wall Ties 316 306 MiTek® Product Catalog Copyright © 2018 MiTek Industries, Inc. All Rights Reserved General Hardware Bridging pg.
General Hardware Copyright © 2018 MiTek Industries, Inc.
General Hardware PC / RC Plywood Clips Steel plywood clips. All models feature embossed dimples to provide 1/8" gap. Provides 1/8" gap Materials: PC – 20 gauge; RC – 18 gauge Finish: G90 galvanizing Maximum Span Span MiTek USP 1 Rating Stock No. RC38-250 24 PC716 32 40 48 PC1532 PC12 PC1932 PC58 PC34 Ref. No. PSCL3/8 PSCL7/16 PSCL15/32, PSCA15/32 PSCL1/2 PSCL19/32 PSCL5/8 PSCL3/4 1 Plywood PC's Thickness Per Code (in) Span Ref.
General Hardware TT D.I.Y. Products Connectors for homeowner / D.I.Y. Projects. TTA12-TZ – an angle connects two 1x wood members at 90º angles. Uplift TTA2-TZ – an angle connects two 2x wood members at 90º angles. F2 TTB22-TZ – a bracket connects two intersecting 2x wood members at 90º angles. TTC24-TZ – a corner tie connects 2x wood members at 90º to the corner of a 2x4 post. Mirror design allows for post to be oriented in either direction.
General Hardware ICPL / KNS / PL Protection Plates Easy-to-install plates protect plumbing and power/communication wiring from nail or screw penetration. 16 gauge steel conforms to protection shield plate requirements of the National Electrical Code and International Plumbing Code. ICPL58 – Installs with nails. W H KNS1 / PL4 – Prongs allow for quick installation.
HFS Compression & Tension Straps General Hardware The HFS Hardy Frame® Saddle is a 14 gauge steel channel intended to be used as a splice at locations where plumbing or other vertical penetrations destroy the structural integrity of a wall’s top plates. 4-1/2" max 4-1/2" max Materials: 14 gauge Finish: G60 galvanizing Codes: IBC, FL, LA Typical HFS installation to underside of double top plates. Installation: • Use all specified fasteners. See Product Notes, page 18.
KRPS Repair Straps General Hardware L Typical KRPS installation Installation: • Use all specified fasteners. See Product Notes, page 18. • Install one strap tie for each 2x plate. MiTek USP 3 Stock No. Steel Ref. No. Gauge KRPS18 RPS18 16 Corrosion Finish KRPS22 RPS22 16 Stainless Steel Gold Coat HDG Triple Zinc KRPS28 RPS28 16 W L 1-1/2 18-5/16 Notch Width (in) < 5-1/2 1-1/2 22-5/16 < 5-1/2 1-1/2 28-5/16 < 12 Fastener 2 Schedule DF/SP Allowable 1 Loads (Lbs.
General Hardware RWB / WB / WBC / WBT Wall Bracing Wall bracing products are engineered to meet the prescriptive 1x4 let-in brace code requirements. RWB – Flat bracing conveniently packaged in a handy roll out dispenser. Perfect for unexpected job site shortages. The 35-pound dispenser pack fits easily into a truck bed for transport. Pre-embossed snap-off points can be broken off by hand (wear gloves for safety).
General Hardware O / N Bridging O – The O series spans three joists in under/over installation. Prong teeth in the center help reduce nailing. N – The N series spans two joists per unit. Can be used for bridging or bracing I-Joists. See chart. Materials: See chart Finish: G90 galvanizing Codes: IBC, FL, LA Typical O installation Installation: • Use specified fasteners in models with fastener requirements.
General Hardware MB / MBG Bridging MBG – Grip tooth bridging. Features special teeth which grip joists and provide easy single-nail installation. Can be installed after subfloor is in place. MB16 – Snap-on, no-nail bridging can be placed in existing floor systems where joist movement is suspected. Two-piece construction creates a solid diagonal brace against joist movement. MB16 Installation: • Use specified fasteners in models with fastener requirements.
General Hardware SB Shelf Brackets This shelf bracket combines shelving capabilities and closet rod support in a one-piece design. 11" Materials: 13 gauge Finish: Zinc Plated 11" 12" 1 MiTek USP Steel Fastener Schedule Code Stock No. Ref. No. Gauge Ref. Qty Type SB12 SBV 13 8 10d -- SB12 Typical SB12 installation 1) NAILS: 10d nails are 0.148" dia. x 3" long. KSCT Corner Tie The Corner Tie secures three-way wood-to-wood connections.
General Hardware NP Nail Plates The NP Nail Plates are an ideal economical solution for attaching wooden members together in a non-structural connection. Also may be used as a prescriptive top plate splice per the International Residential Code (IRC). They are pre-punched for 8d common nails. W Wall framing Installation: • Use nails appropriate for intended use. Holes are sized for 8d common (0.131" dia. x 2-1/2" long) or 8d (0.131" dia.) x 1-1⁄2" nails.
Specialty Options Specialty Options pg. 320-325 Face Mount Hanger 321 Open Top Flange Hanger 322 Part Number System 325 Solid Top Flange Hanger Specialty Options & General Notes 323-324 325 Specialty Options Welded Top Flange Hanger 320 318 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Specialty Options Copyright © 2020 MiTek Industries, Inc.
Specialty Options Specialty Options & General Notes Finish: See specific hanger option tables. Welded hangers are painted with gray primer. Non-catalog hangers available in Hot-dip galvanized, use HDG after product number. Allowable Loads: For multiple options for the same connector, use the most conservative reduction to give the lowest design load. See specific hanger option tables for applicable load reductions and maximum tolerances.
Specialty Options Face Mount Hanger Specialty Details See the Specialty Options Chart for each hanger series for load reductions and hanger maximum range of skew, slope, etc. Skewed Hanger: • Consider SKH or SKHH hangers for 45° skews. • Joist nails on the closed side may be relocated to the open side by MiTek designer to ensure proper nailing. • Specify skew angle, type (square cut or bevel cut), and direction when ordering. Sloped Seat Hanger: • Consider LSSH series for sloped applications.
Open Top Flange Hanger Specialty Details Specialty Options See Specialty Options Chart for each hanger series for load reductions and hanger maximum range of skew, slope, etc. Skewed Hanger: • Joist nails may be located on obtuse angle side by MiTek designer to ensure proper nailing. • Specify skew angle, type (square cut or bevel cut), and direction when ordering.
Specialty Options Solid Top Flange Hanger Specialty Details Sloped/Skewed Hanger: • See nailing notes above for both Skewed Hanger and Sloped Seat Hanger. • Specify skew and slope angles as well as skew/slope directions, and skew type (square cut or bevel cut) when ordering. • Specify if hanger is to be high side flush, low side flush, or center flush. Sloped Top Flange Hanger: • Additional nail holes may be added to top angle by MiTek designer. • Specify top flange slope and direction when ordering.
Top Flange Hanger Nailer Options Specialty Options Specialty Options Copyright © 2020 MiTek Industries, Inc.
Specialty Options Welded Top Flange • Weld sizes and lengths shown on chart. • Weld-on applications produce maximum allowable load listed. Uplift loads do not apply to this application. • All welding should be done in accordance with the American Welding Society (AWS) Standard by a certified welder. Caution: Welding galvanized steel may produce harmful fumes and should only be performed in well-ventilated environments.
Cold-Formed Steel Connectors Cold-Formed Steel pg. 328-339 Angles 334 Concrete Screw Anchors 329 Fastening Information 328 Girder Tiedowns 338 336-337 Holdowns 330-333 339 Straps 335 Stud Plate Ties 338 CFS Connectors Hurricane Ties 326 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
Copyright © 2020 MiTek Industries, Inc.
Fastening Information Cold-Formed Steel Connectors MiTek recommends the use of hex head metal screws with a self-drilling tip, for ease of installation and strength. Screw diameter ranges from 0.190" to 0.250" and is specified for each connector in their corresponding load table. An important factor to consider when selecting a self-drilling screw is the material thickness specifically the combined side and main member thickness.
Cold-Formed Steel Connectors PFM Concrete Screw Anchors Screw-Bolt+ anchors are a one-piece, heavy duty screw anchor with a finished hex head. The patented thread design, designed for use with standard ANSI drill bits, reduces installation torque and enhances productivity. The steel threads along the anchor body tap into the hole during installation to provide keyed engagement and allow for reduced edge and spacing distances.
Cold-Formed Steel Connectors S/PHD Holdowns The S/PHD holdowns are high performance ductile holdowns used for providing a tension connection between CFS framing members and the foundation or other structural members. The pre-deflected design keeps deflection low. The S/PHD holdowns attach with #14 self-drilling screws making installation an ease, saving time and labor. Materials: S/PHD4, S/PHD6 – 14 gauge; S/PHD9 – 12 gauge Finish: G90 galvanizing Codes: IBC Installation: •U se all specified fasteners.
Cold-Formed Steel Connectors HTT14S / LTS20B Holdowns The LTS20B and the HTT14S tension ties are designed for both new construction and retrofit applications for concrete-to-steel connections and do not require an additional washer. LTS20B is a light capacity tension tie strap with a 1/4" load transfer plate. Materials: See chart Finish: Strap – G90 galvanizing; Plate – Primer Installation: • Use all specified fasteners. • A ttach the strap portion of the connector to the steel stud.
Cold-Formed Steel Connectors DTB/S Holdown The DTB/S-TZ may be used to resist tension loads installed to CFS members. Materials: 14 gauge Finish: G-185 galvanizing Installation: • Use all specified fasteners. • Install screws to attach DTB/S-TZ to framing member first. • Install with MiTek’s THR 1/2" threaded rod or equivalent. • Tighten anchor bolt nutsfinger tight to base plus 1⁄3 to 1⁄2 additional turns with wrench. L CL D W DTB/S-TZ Dimensions (in) MiTek USP Stock No.
Cold-Formed Steel Connectors TDS Holdowns W The TD8S, TD10S, and TD15S are high capacity holdowns which are designed for attachment to cold formed steel (CFS) framing members. Holdowns are secured at the base by attachment to an anchor bolt. 1-3/4" Materials: See chart Finish: Primer L Installation: • U se #10 self-tapping screws to attach the back or strap portion of the holdown to a steel stud. Install nut to secure the base of holdown to foundation with anchor bolt of specified diameter.
Cold-Formed Steel Connectors MP/S Skewable Angles MP/S angles are field-adjustable to attach members intersecting at angles. MP/S angles are load rated and provide adequate thickness and fastener quantity to the field fabricated clip angles. 2 1⁄4" 2 1⁄4" 2 1⁄4" 2 1⁄4" Materials: 18 gauge Finish: G90 galvanizing 5 7⁄8" Installation: • Use all specified fasteners. • Field-adjustable from 45°-180° (flat). Bend angle only once. • Joist must be constrained from rotation.
Cold-Formed Steel Connectors CMST / CMSTC / RS Coiled Strapping MiTek straps may be used to create a tension connection between multiple CFS members with the use of self-tapping screws. 3" 1-1/2" 3" 1-1/4" 2-1/4" 1/2" 3/4" 1" Materials: See chart Finish: G90 galvanizing 3/8" 1-1/2" Installation: • Use all specified fasteners. • Install equal amount of screws on each end of tension connection. 3/4" 1-3/4" 1-1/2 3" 3-1/2" CMST Dimensions Copyright © 2020 MiTek Industries, Inc.
Cold-Formed Steel Connectors HDO/S / HDOL/S Top Mount Bridle Hangers HDOL/S (14 ga) and HDO/S (12 ga) top mount bridle hangers are available in a wide variety of stock sizes to match the most common framing needs with economical solutions where custom or special order hangers were required before. The revolutionary design utilizes shear lag slots designed to maximize the capacity of the hangers while providing a safe and ductile connection.
Cold-Formed Steel Connectors FWH/S Fire Wall Hangers The FWH/S Fire Wall Hanger attaches to cold-formed steel wall framing to support cold-formed steel joists. A 2-layers 5/8" gypsum wallboard Materials: 14 gauge Finish: G90 galvanizing Options: See Specialty Options chart Installation: • I nstall prescribed type and number of self-drilling screws through the round holes into the wall track. Install (5) self-drilling screws through the hanger into one side of the joist using the round and slotted holes.
Cold-Formed Steel Connectors SPT Stud Plate Ties MiTek SPT4 and SPT6 Stud Plate Ties may be used to create a tension and bearing connection between multiple CFS members with self-tapping screws. Materials: 20 gauge Finish: G90 galvanizing H Installation: • Wrap SPT tie around top or bottom track. • Use all specified fasteners. W Dimensions (in) Fastener Schedule Allowable Uplift Loads 100% (Lbs.)1 MiTek USP Steel Stock No. Ref. No.
Cold-Formed Steel Connectors RT/S Hurricane Ties RT/S are designed to tie trusses and rafter to wall systems. RT/S are to resist uplift and lateral forces between framing members. Materials: 20 gauge Finish: G90 galvanizing 1-9/18" 1-9/16" 1-9/16" Installation: • Use all specified fasteners. • Designer shall determine if solid blocking is required.
MH Connectors Manufactured Housing Connectors Manufactured Housing pg. 342-349 347 Hangers 344 Installation Notes 342 Nails 343 Nail Plates 348 Plate Tie 347 Post Anchors 348 Protection Plates 349 Rafter Ties Stud Plate Ties 340 345-346 346 MiTek® Product Catalog Copyright © 2020 MiTek Industries, Inc.
MH Connectors Copyright © 2020 MiTek Industries, Inc.
Manufactured Housing Connectors MH Connectors Installation Notes Catalog installation notes should be followed when installing pneumatic nail hangers using alternative nails. All fasteners should be installed into nailing zones and maintain minimum 1" center-to-center spacing. Alternative nail quantity required for installation of pneumatic nail hangers can be determined using the table below.
Manufactured Housing Connectors MiTek® TECO™ 33º Collated Nails MH Connectors MiTek® TECO™ 33° collated pneumatically driven nails feature a color coded head-ID stamp system that makes it easy to verify the proper nail has been used. The 33° collated nails can serve as an alternate to hand-driven installation of the following nails and may be used with many MiTek products.
Manufactured Housing Connectors MH Connectors JN / JNE / MTHF Hangers MiTek’s “no hole” connectors are engineered for wood frame structures built in a factory environment. These connectors feature embossed “nailing zones” for faster and safer fastener installation. Materials: 18 or 20 gauge Finish: G90 galvanizing Codes: See chart for references Installation: • Install all specified fasteners using a pneumatic nailer. • Nailing zones are distinguished by embossed pattern.
Manufactured Housing Connectors RST3 Rafter Tie Materials: 18 gauge Finish: G90 galvanizing MH Connectors The RST3 rafter tie is designed to anchor trusses and rafters directly to the stud below. The ability to field-bend the RST3 permits fastening to either the wide or narrow face of the stud. L Installation: • Use all specified fasteners. • I f necessary, field bend the lower tab of the RST3 at 90° at the two bend slots. W • Not all fastener holes need to be filled.
Manufactured Housing Connectors MH Connectors MRT7 Rafter Tie The MRT7 Rafter Tie is engineered for wood frame structures built in a factory environment. These connectors feature embossed “nailing zones” for faster and safer fastener installation. Materials: 14 gauge Finish: G90 galvanizing Installation: • Install all specified fasteners using a pneumatic nailer. • Nailing zones are distinguished by embossed pattern.
Manufactured Housing Connectors MPF Multi-Lateral Plate Tie H Connects 2x framing with floor sheathing up to 5/8". Materials: 20 gauge Finish: G90 galvanizing Options: See chart for Corrosion Finish Options Codes: IBC, FL, LA 1" 4-1/4" Header or Stud Joist or Plate Steel Installation 2,4 Qty Type Qty Type Gauge Type Type 1 Typical MP4F installation 4,5 DF/SP 1,3 Allowable Loads (Lbs.) S-P-F 1,3 Allowable Loads (Lbs.
Manufactured Housing Connectors Porch design for any structure must account for the wind exposure. Porches present lots of sail area to catch the wind and can develop very high wind uplift in ordinary wind events. They must be securely tied to the foundation. MiTek engineers and manufactures products intended to provide a load path from the porch components to the foundation.
Manufactured Housing Connectors Plumbing / Electrical Protection Plates MH Connectors Easy-to-install plates protect plumbing and power/communication wiring from nail or screw penetration. ICPL58 – Installs with nails KNS1 / PL4 – Prongs allow for quick installation W Materials: 16 gauge Finish: ICPL516-TZ – G-185 galvanizing; All other – G90 galvanizing. Options: See chart for Corrosion Finish Options Installation: • Use all specified fasteners.
Lateral Systems Lateral Systems Lateral Systems pg. 352-354 Hardy Frame® CFS Moment Frames 353 Hardy Frame® Moment Frames 353 Hardy Frame® Shear Walls 352 Z4 Tie-Down Systems 354 Copyright © 2020 MiTek Industries, Inc.
Lateral Systems Copyright © 2020 MiTek Industries, Inc.
Lateral Systems Hardy Frame® Shear Walls Shear Wall Systems Hardy Frame® Code Evaluation Hardy Frames has been leading the pre-manufactured shear wall industry from its beginning. Hardy Frames were the first to be recognized by ICBO-ES and LA City, first to gain approval for multi-story applications, first Balloon Wall application and first to be recognized to comply with the 2003 and 2006 IBC and IRC Building Codes.
The First and Only Cold Formed Steel (CFS) Moment Frames The all new MiTek Hardy Frame® CFS Moment Frame and CFS Picture Frame are the industries first standardized, pre-engineered, pre-manufactured cold formed steel moment frames. Lateral Systems Shear Wall Systems Lighter and less cost than structural steel moment frames, our CFS product line provides high capacities, ductility and cost economics that complete a spectrum of MiTek shear wall solutions.
MiTek® Z4 Tie-Down System for Lateral Load 1. Z-Rod 2. Cinch nut 3. MiTek® Pro Series Screw 4. Bearing Plate Washer 5. Wood Framing To resist tension loads due to overturning moments in multi-story buildings the CNX Cinch Nut is installed over a Bearing Plate Washer at each level in a fast and easy application. At the upper-most level a Cinch Nut is installed over a Bearing Plate Washer above the top plates.
MiTek Services Division FOCUSED ON HELPING YOU GROW YOUR BUSINESS WITH HIGHLY SKILLED RESOURCES THAT SCALE AS YOUR REQUIREMENTS CHANGE. EXPAND YOUR CAPABILITIES WITHOUT ADDING STAFF. MiTek Industries, Inc. Providing integrated solutions to the construction industry.
MiTek Services Division FOCUSED ON HELPING YOU GROW YOUR BUSINESS WITH HIGHLY SKILLED RESOURCES THAT SCALE AS YOUR REQUIREMENTS CHANGE. EXPAND YOUR CAPABILITIES WITHOUT ADDING STAFF. MiTek Industries, Inc. Providing integrated solutions to the construction industry.
MiTek Services Division FOCUSED ON HELPING YOU GROW YOUR BUSINESS WITH HIGHLY SKILLED RESOURCES THAT SCALE AS YOUR REQUIREMENTS CHANGE. EXPAND YOUR CAPABILITIES WITHOUT ADDING STAFF. MiTek Industries, Inc. Providing integrated solutions to the construction industry.
MITEK IS MORE THAN JUST ENGINEERED PRODUCTS AUTOMATION Our comprehensive offsite design and fabrication solutions are changing the way the world is building. MiTek-US.com/Machinery SERVICES Scale your outputs (design, take-offs, estimating, job quotes, and more) without scaling your labor costs with MiTek® PlanServices™. MiTek-US.
MADE IN AMERICA. DESIGNED TO LAST. MiTek Structural Connectors are manufactured and distributed in 9 strategic locations in the United States. We are proud that our structural connector products are designed and made in the USA.
