Use and Care Manual

111
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Angles & Straps
Angles & Straps
MiTek
®
Product Catalog
MP / MPA / MPF Multi-Purpose Framing Angles
Ref. No. Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
6 8d x 1-1/2 6 8d x 1-1/2 F1
600 615 615 615 515 515 515 515
6 8d x 1-1/2 6 8d x 1-1/2 F2
600 685 735 750 515 585 630 630
6 8d x 1-1/2 6 8d x 1-1/2 F3 280 320 350
435
180 205 225 290
6 8d x 1-1/2 3 8d x 1-1/2 A1
300 340 370 370 260 295 310 310
6 8d x 1-1/2 3 8d x 1-1/2 B1
300 340 370 385 260 295 315 325
6 8d x 1-1/2 3 8d x 1-1/2 C1
255 255 255 255 215 215 215 215
6 8d x 1-1/2 6 8d x 1-1/2 A2
440 440 440 440 350 370 370 370
6 8d x 1-1/2 6 8d x 1-1/2 B2
240 240 240 240 200 200 200 200
6 8d x 1-1/2 6 8d x 1-1/2 C2
330 330 330 330 280 280 280 280
4 8d x 1-1/2 4 8d x 1-1/2 F1
400 455 490
525
345 390 420 440
4 8d x 1-1/2 4 8d x 1-1/2 F2
400 455 490 590 345 390 420 495
4 8d x 1-1/2 4 8d x 1-1/2 F3 185 215 230 295 120 140 150 190
6 8d x 1-1/2 6 8d x 1-1/2 V 590 670 720 750 505 575
615
645
6 8d x 1-1/2 6 8d x 1-1/2 H 590 670 720 750 505 575
615
645
6 8d x 1-1/2 6 8d x 1-1/2 V 590 670 720 750 505 575
615
645
6 8d x 1-1/2 6 8d x 1-1/2 H 585 585 585 585 505
575 615 645
6 8d 6 8d V 590 670 720 750 505 575
615
645
6 8d 6 8d H 590 670 720 750 505 575
615
645
6 8d 6 8d V 590 670 720 750 505 575
615
645
6 8d 6 8d H 585 585 585 585 505
575 615 645
6 8d x 1-1/2 6 8d x 1-1/2 V 590 595 595 595 505 510 510 510
6 8d x 1-1/2 6 8d x 1-1/2 H 590 595 595 595 505 510 510 510
6 8d x 1-1/2 6 8d x 1-1/2 V 590 595 595 595 505 510 510 510
6 8d x 1-1/2 6 8d x 1-1/2 H 590 595 595 595 505 510 510 510
6 8d 6 8d V 590 595 595 595 505 510 510 510
6 8d 6 8d H 590 595 595 595 505 510 510 510
6 8d 6 8d V 590 595 595 595 505 510 510 510
6 8d 6 8d H 590 595 595 595 505 510 510 510
1) Allowable loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) Refer to drawings for installation type and definition of the various load directions.
3) If installing MP4F or MP6F over plywood, use 8d common nails for 100% of table load.
4) Loads are shown per angle. When using a single anchor, joist must be constrained from rotation.
5) Stainless steel ring shank nails must be used with stainless steel connectors to achieve tabulated allowable loads.
6)
NAILS:
8d x 1-1/2 nails are 0.131" dia. x 1-1/2" long, 8d nails are 0.131" dia. x 2-1/2" long
New products or updated product information are designated in
blue font
.
IBC,
FL,
LA
Code
Ref.
Fastener Schedule
5,6
Corrosion
Finish
DF/SP
Allowable Loads (Lbs.)
1,3,4
S-P-F
Allowable Loads (Lbs.)
1,3,4
Steel
Gauge
Direction
of Load
2
A35
MiTek USP
Stock No.
Installation
Type
2,4
Joist or PlateHeader or Stud
MPA1
Figure 1
Figure 2
Figure 3
18
Type 1
Type 2
MP6F LTP5 20
MP34
Type 1
Type 2
Type 1
Type 2
MP4F LTP4 20
Type 1
Type 2
A34 18 Figure 4
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• Bend tabs only once.