Use and Care Manual

116
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Angles & Straps
Angles & Straps
MiTek
®
Product Catalog
RSPT / SPT / TSP Stud Plate Ties
RSPT – 18 or 20 gauge
SPT – 20 gauge
TSP – 16 gauge. Optional diamond holes for
various uplift capacities with Min and Max
nailing congurations
Materials: See chart
Finish: G90 galvanizing
Options: See chart for Corrosion Finish Options
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes,
page 18.
• TSP Min Nailing – Fill all round holes.
• TSP Max Nailing – Fill all round and
diamond holes.
• HDG nails may be required when
fastening to treated sill plates.
Typical SPT24
installation
SPT22
Typical RSPT6-2
installation
RSPT6-2RSPT6
Typical RSPT4 single
plate installation
Typical RSPT4 double
plate installation
RSPT4
H
W
Reinforcement
ribs
Holding
cleat
Ref. No. W H L Qty Type Qty Type
RSPT4 RSP4 20 1-1/2 4-1/8 -- 4 8d x 1-1/2 4 8d x 1-1/2 460 255 300 -- --
SPT22 SP1 20 1-9/16 4-3/8 3-1/2 4 10d 4 10d 735 535 275 -- --
SPT24 SP2 20 1-9/16 5-5/8 3-1/2 6 10d 6 10d 1090 535 275 -- --
SPT44 -- 20 3-9/16 6-3/4 6-1/2 6 16d 6 16d 1315 845 275 -- --
RSPT6 SSP 18 1-1/2 5-7/16 -- 4 10d x 1-1/2 4 10d x 1-1/2 650 -- -- -- --
RSPT6-2 DSP 18 2-3/4 5-7/16 -- 8 10d x 1-1/2 6 10d x 1-1/2 900 -- -- -- --
3 10d x 1-1/2 3 10d x 1-1/2 465 -- -- -- --
10d x 1-1/2 830
10d 870
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) SPT22, SPT24, and SPT44: the nails fastened to the wide face of the stud must be driven 30° from the perpendicular
on the horizontal plane.
3)
NAILS:
8d x 1-1/2 nails are 0.131" dia. x 1-1/2" long, 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long,
10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
1-5/8 7-7/8 --
235
IBC,
FL,
LA
Code
Ref.
DF/SP
Allowable Loads (Lbs.)
TSP TSP 16
Uplift
1
160%
F1
160%
F4
160%
Dimensions (in)
Corrosion
Finish
Plate
MiTek USP
Stock No.
2
Steel
Gauge
Fastener Schedule
3
Stud
F2
160%
F3
160%
210365 1909 10d x 1-1/2 6
H
L
W
5-7/16"
1-1/2"
5-7/16"
2-3/4"
TSP
H
1-5/8"
W
Additional
diamond holes
for max nailing
Standard round
holes for
min nailing
Typical TSP top plate
installation (max nailing)
Typical TSP-TZ mudsill
installation (min nailing)
Uplift
F1
F1
F2
F2
Uplift
F1
F1
F2
F2
Uplift
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
F3
F2
F1
F4
Uplift
Uplift