Use and Care Manual

186
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Lumber Hangers
Lumber Hangers
MiTek
®
Product Catalog
2" min
8" min
8" min
HD Masonry Face Mount Hangers
The HD series Face Mount hangers can be used to connect roof framing
members, trusses, and oor joists to masonry walls.
Materials: 14 gauge
Finish: G90 galvanizing
Installation:
• Masonry screws shall be Powers
®
Tapper+
®
HWH 3/16" x 1-3/4".
Typical HD
top installation
(ush to top only)
Typical HD
corner installation
(ush to edge and top)
Typical HD
edge installation
(ush to edge only)
W
H
D
Qty Qty
Type
8
Field Edge Top Corner Field Edge Top Corner
HD26 HU26 14 1-9/16 3-1/2 2-1/2 4 3/16" x 1-3/4" 4 10d x 1-1/2 1000 495 670 335 145 70 145 45
HD28 HU28 14 1-9/16 5-1/4 2-1/2 8 3/16" x 1-3/4" 6 10d x 1-1/2 2000 990 1340 665 595 295 595 195
HD210 HU210 14 1-9/16 7-3/16 2-1/2 14 3/16" x 1-3/4" 6 10d x 1-1/2 3110 1545 2085 1035 595 295 595 195
HD212 -- 14 1-9/16 9-13/16 2-1/2 20 3/16" x 1-3/4" 10 10d x 1-1/2 3640 1805 2440 1210 595 295 595 195
HD26-2 HU26-2 14 3-1/8 5-1/4 2-1/2 12 3/16" x 1-3/4" 6 10d 3000 1490 2015 1000 1170 580 850 380
HD28-2 HU28-2 14 3-1/8 7-1/8 2-1/2 14 3/16" x 1-3/4" 6 10d 3500 1735 2350 1165 1170 580 850 380
HD210-2 HU210-2 14 3-1/8 9 2-1/2 20 3/16" x 1-3/4" 10 10d 5000 2480 3355 1665 1950 645 850 420
HD212-2 HU212-2 14 3-1/8 11 2-1/2 24 3/16" x 1-3/4" 12 10d 5750 2850 3860 1915 2340 645 850 420
HD44 HU44 14 3-9/16 3-5/16 2-1/2 4 3/16" x 1-3/4" 2 10d 1000 495 670 335 145 70 145 45
HD46 HU46 14 3-9/16 5-1/16 2-1/2 12 3/16" x 1-3/4" 6 10d 3000 1490 2015 1000 1170 580 850 380
HD48 HU48 14 3-9/16 6-15/16 2-1/2 14 3/16" x 1-3/4" 6 10d 3500 1735 2350 1165 1170 580 850 380
HD410 HU410 14 3-9/16 8-13/16 2-1/2 20 3/16" x 1-3/4" 10 10d 5000 2480 3355 1665 1950 645 850 420
HD412 -- 14 3-9/16 10-13/16 2-1/2 24 3/16" x 1-3/4" 12 10d 5750 2850 3860 1915 2340 645 850 420
HD26-3 HU26-3 14 4-5/8 4-1/2 2-1/2 12 3/16" x 1-3/4" 6 10d 3000 1490 2015 1000 1170 580 850 380
HD28-3 -- 14 4-5/8 6-3/8 2-1/2 14 3/16" x 1-3/4" 6 10d 3500 1735 2350 1165 1170 580 850 380
HD210-3 HU210-3 14 4-5/8 8-1/4 2-1/2 20 3/16" x 1-3/4" 10 10d 5000 2480 3355 1665 1950 645 850 420
HD212-3 HU212-3 14 4-5/8 10-1/4 2-1/2 24 3/16" x 1-3/4" 12 10d 5750 2850 3860 1915 2340 645 850 420
HD5210 -- 14 5-3/8 7-7/8 2-1/2 20 3/16" x 1-3/4" 10 10d 5000 2480 3355 1665 2305 645 850 420
HD5212 -- 14 5-3/8 9-7/8 2-1/2 24 3/16" x 1-3/4" 12 10d 5750 2850 3860 1915 2765 645 850 420
HD66 HU66 14 5-1/2 4-1/16 2-1/2 12 3/16" x 1-3/4" 6 10d 2350 1165 1575 780 1380 645 850 420
HD68 HU68 14 5-1/2 5-15/16 2-1/2 14 3/16" x 1-3/4" 6 10d 3500 1735 2350 1165 1380 645 850 420
HD610 HU610 14 5-1/2 7-13/16 2-1/2 20 3/16" x 1-3/4" 10 10d 5000 2480 3355 1665 2305 645 850 420
HD612 HU612 14 5-1/2 9-13/16 2-1/2 24 3/16" x 1-3/4" 12 10d 5750 2850 3860 1915 2765 645 850 420
1) Allowable loads assume the use of Powers® Tapper+® HWH 3/16" x 1-3/4".
2) Fasteners to be installed per manufacturer's recommendations.
3) Field installation indicates that the uppermost and outermost fasteners are a minimum of 8" from the top and side of the masonry wall.
4) Edge installation indicates that the hanger is installed flush with the edge of the masonry wall.
5) Top installation indicates that the hanger is installed with the hanger flush with the top of the wall.
6) Corner installation indicates that the hanger is installed in the corner of the masonry wall flush to the edge, and the top fastener is less than 2" from the top.
7)
Minimum 6" wide grout-filled concrete masonry units with a minimum compressive strength of 1,500 psi (10.3 MPa).
8)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2 long, 10d nails are 0.148 dia. x 3" long.
New products or updated product information are designated in
blue font
.
Code
Ref.
--
Uplift (160%)Joist/Beam
Masonry
7
Download (100%)
MiTek USP
Stock No.
Steel
Gauge
DF/SP Allowable Load (Lbs.)
1,4,5,6
Dimensions (in)
Fastener Schedule
2
Tapper+® HWH
Screw AnchorRef No.
Typical HD
eld installation
2" min