Use and Care Manual

210
MiTek
®
Product Catalog
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
EWP Hangers
EWP Hangers
THD / THDH Face Mount Hangers
THD – Medium capacity hanger for LVL, LSL, and PSL beams
THDH – Heavy capacity hanger for LVL, LSL, and PSL beams
Materials: See EWP Face Mount Hangers charts, pages 218-220
Finish: G90 galvanizing
Op tions: Rough/ Full sizes available for THD series. THD
hangers with widths greater than 3" can have one ange
inverted with no load reduction. Specify left (L) or (R) ange.
See Specialty Options chart.
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• THD – Drive bend line nails into header at 45° to achieve
listed loads.
• THDH – Drive joist nails into header at 30° to 45° to achieve
listed loads.
Specialty Options Chart
– refer to Specialty Options pages 320-321 for additional details.
Option
MiTek USP
Series
Skewed
1,3,4
Sloped Seat
2
Sloped / Skewed
1,2,3,4
Inverted Flange
THDH N/A
1
)
Skewed han
g
ers with skews
g
reater than 15° ma
y
have all
j
oist nailin
g
on outside flan
g
e. All skewed THDH han
g
ers have
j
oist nails on one side onl
y
.
2
)
Slo
p
ed or slo
p
ed / skewed han
g
ers with slo
p
es
g
reater than 15° ma
y
have additional
j
oist nails.
3
)
THDH models - Skewed han
g
ers t
yp
icall
y
re
q
uire a bevel cut. A s
q
uare cut o
p
tion ma
y
be available as a custom.
4
)
THD models - For skewed han
g
ers, the re
q
uired cut t
yp
e
(
s
q
uare or bevel
)
of
j
oist member ma
y
var
y
based on skew an
g
le
and width of han
g
er. Some s
q
uare cut han
g
ers will re
q
uire custom
p
ricin
g
due to welded back
p
late.
See Sloped Seat and Skewed
Ex. THDH410_SK45R_BV_SL30D
THD
THDH
Ordering
Range
Allowable
Loads
THDH
THD
THD
Add
IF, one flange,
right
(R) and left (L),
Ex. THD410_IFR
1˚ to 45˚ 1˚ to 45˚ See Sloped Seat and Skewed
N/A
65% of table load
85% of table load.
50% of table uplift load.
100% of table load.
65% of table load when
nailing into the support
members end grain.
85% of table load
Add
SK, angle required,
right
(R) or left (L), and
square cut
(SQ) or bevel cut (BV)
to product number.
Ex. THDH410_SK45R_BV
Add
SL, slope required,
and up
(U) or down (D),
to product number.
Ex: THDH410_SL30D
65% of table load
N/A52% of table load
52% of table load.
50% of table uplift load.
Not available in widths < 3".
Widths >
3" can have
one flange inverted.
Some model designs
may vary from
illustration shown
Typical THDH
installation
Typical THD
installation
Typical THDH double
shear installation
Typical bend line nailing
installation
THD410
THDH
Drive joist nails into
header at 30° to 45° to
achieve listed loads.
H
D
W
H
D
W
Raised dimple
allows 30° to
45° nailing
2-1/2"
Drive bend line nails
into header at 45º to
achieve listed loads
Bend line nailing
where applicable
Obround hole
nailing
where applicable
THD7210
W
3"
Bend line
nailing
D
H
A