Manualshelf

Use and Care Manual

ManualsBrandsMiTek ManualsBuilding Hardware1-1/2 in. x 1-1/2 in. x 1-1/4 in. G185 16-Gauge Framing Angle (1-Pack)
211212213214215216217218219220
212
MiTek
®
Product Catalog
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
EWP Hangers
EWP Hangers
I-Joist Charts Face Mount Hangers
Dimensions (in)
Ref. No. W H D A Qty Type Qty Type 100% 115% 125% 100% 115% 125%
IHFL23112
IUS2.37/11.88 -- 18 2-5/16 11-3/16 2-1/2 1-1/8 -- 10 10d -- -- 1200 1370 1475 50 1040 1185 1275 40
Min 10 10d 1250 1405 1515 1100 1235 1330
Max 24 16d 3530
3960 3960
2675 2705 2725
Min 12 1440 1640 1770 1245 1420 1530
Max 14 1680 1915 2065 1455 1660 1785
Min 12 10d 1500 1685 1815 1320 1480 1595
Max 28 16d 4115 4440 4440 2675 2705 2725
Min 14 1680 1915 2065 1455 1660 1785
Max 16 1920 2190 2360 1660 1895 2040
Min 14 10d 1750 1965 2120 1540 1730 1865
Max 30 16d 4410 4440 4440 2675 2705 2725
Min 14 10d 1750 1965 2120 1540 1730 1865
Max 30 16d 4410 4440 4440 2675 2705 2725
THFI2595
IUS2.56/9.25,
IUS2.56/9.5
-- 18 2-5/8 9-1/2 2-1/2 1-3/8 -- 8 10d -- -- 960 1095 1180
125
845
965 995 100
IHFL25925
-- -- 18 2-1/2 9-1/8 2-1/2 1-1/8 -- 8 10d -- -- 960 1095 1180 50 830 945 1020 40
Min 10 10d 1250
1375 1375 1085 1085 1085
Max 24 16d 3530 4000 4320 2875 2905 2920
THFI25118 IUS2.56/11.88 -- 18 2-5/8 11-7/8 2-1/2 1-3/8 -- 10 10d -- -- 1200
1265 1265 125 995 995 995 100
IHFL25112
-- -- 18 2-1/2 11-1/8 2-1/2 1-1/8 -- 10 10d -- -- 1200 1370 1475 50 1040 1185 1275 40
Min 10 10d 1250
1375 1375 1085 1085 1085
Max 24 16d 3530
3960 3960
2875 2905 2920
Min 12 10d -- -- 1440 1640 1770 1265 1445 1555
Max 14 10d -- -- 1680 1915 2065 1480 1685
1815
Min 12 10d 1440 1640 1770 1245 1420 1530
Max 14 10d 1680 1915 2065 1455 1660 1785
Min 12 10d 1500 1685 1815 1320 1480 1595
Max 28 16d 4115 4440 4440 2875 2905 2920
Min 14 1680 1915 2065 1455 1660 1785
Max 16 1920 2190 2360 1660 1895 2040
Min 14 10d 1750 1965 2120 1540 1730 1865
Max 30 16d 4410 4440 4440 2875 2905 2920
Min 10 10d 1250
1375 1375 1085 1085 1085
Max 24 16d 3530 4000 4320 3010 3035 3055
Min 10 10d 1250 1375 1375
1085 1085 1085
Max 24 16d 3530
3960 3960
3010 3035 3055
Min 12 10d 1500 1685 1815 1320 1480 1595
Max 28 16d 4115 4440 4440 3010 3035 3055
Min 14 10d 1750 1965 2120 1540 1730 1865
Max 30 16d 4410 4440 4440 3010 3035 3055
Min 10 10d 1250
1375 1375 1085 1085 1085
Max 24 16d 3530 4000 4320 3105 3435 3455
Min 10 10d 1250
1375 1375 1085 1085 1085
Max 24 16d 3530
3960 3960
3105 3125 3125
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) IHFL (18GA) ─ install (2) 10d (0.148") x 1-1/2" nails through diamond dimple holes into the bottom chord of I-Joist member for a total uplift of 220 lbs.
IHF (16GA) ─ uplift capacity for hangers installed without joist nails is 65 lbs.
3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
Load tables address hanger/header/fastener limitations only. Joist limitations must be determined for each installation.
New products or updated product information are designated in blue font.
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-3/8
10d x 1-1/2 330
15-7/16 2-1/2 2 10d x 1-1/2 330
IHF2616
-- --
-- --
260
IHF26925
-- -- 16 2-5/8 9-1/16 2-1/2 2 10d x 1-1/2 260
16 2-5/8 13-3/8 2-1/2
260
260
260
2 10d x 1-1/2 330
3302 10d x 1-1/2-- 16 3-1/8 3 x 11-1/4 10-13/16
IHF15112-2
MIU3.12/11
2-5/8 x 14
2-5/8 x 16
IHF15925-2
MIU3.12/9 -- 16 3-1/8
16 2-5/8
9-3/16 2-1/2
2-1/2
2-1/2 x 16
2-5/8 x
9-1/4 - 9-1/2
2-5/8 x
11-1/4 - 11-7/8
IHFL2514
-- -- 18 2-1/2 13-7/16
15-1/2
IHFL2516
IUS2.56/16 -- 18 2-1/2
IHF2516
MIU2.56/16 -- 16 2-1/2
3 x 9-1/4
IHF2614
40
2-1/2 -- -- 50
2-1/2 2 10d x 1-1/2 330
10d2-1/2 -- -- 50
260
1-1/8
1-1/8
1-1/8
26015-1/2 2-1/2 2 10d x 1-1/2 330
2-5/16 x 11-7/8
2-5/16 x 14
2-5/16 x 16
2-5/16 x 18
2-1/2 x
9-1/4 - 9-1/2
330
330
330
40
260
40
260
260
260
260
2-1/2 x 14
THFI2514 IUS2.56/14
2-1/2 13-7/16
100
2-1/2 11-1/8 2-1/2 2 10d x 1-1/2
IHF25112
MIU2.56/11 -- 16
2-5/8 14 2-1/2-- 18
2-1/2 9-1/8 2-1/2 2 10d x 1-1/2
2-1/2 x
11-1/4 - 11-7/8
40
330
260
2 10d x 1-1/2 330
IHF26112
-- -- 16 2-5/8 11-1/16 2-1/2 2
IHF2514
MIU2.56/14 -- 16
IUS2.37/16
IHF2318
MIU2.37/18 -- 16
IHF25925
MIU2.56/9 -- 16
2-1/2
IHF2314
MIU2.37/14 -- 16 2-5/16
50
IHF2316
MIU2.37/16 -- 16 2-5/16 15-9/16 2-1/2 2 10d x 1-1/2 330
10d2-5/16 15-9/16 2-1/2 -- --
IHFL2316
10d x 1-1/2
Joist Size
(in)
MiTek USP
Stock No.
Min/
Max
Uplift
1,2
160%
Uplift
1,2
160%
260
IHFL2314
IUS2.37/14 -- 18 2-5/16 13-1/2 2-1/2 -- -- 5010d
IHF23112
MIU2.37/11 -- 16 2-5/16 11-3/16
IBC,
FL,
LA
330
125
Code
Ref.
Web
Stiff
Reqd Ga
Fastener Schedule
3
DF/SP Header
Allowable Loads (Lbs.)
S-P-F Header
Allowable Loads (Lbs.)
Header
Joist
2
2 10d x 1-1/2 330
13-1/2 2-1/2 2 10d x 1-1/2
-- 18
2-5/16 17-1/8 2-1/2 2
Continued on next page
H
W
D
A